Pioneer PRV-LX10 Service Manual page 142

1
4) Data on the Encoder board (Page 4)
The data on the Encoder board are displayed. If the [SIDE-A] key is pressed on this page, the error log for the Encoder
board can be checked.
A
An error record is expressed as shown below:
(Example) 2003/07/01 10:30:20 == 09 03 ==
The meaning of the error codes and correction measures are described below:
Code Content of Error
B
01 Data Read Timeout Error
02 Copy Protection Error
(task ID : 09(h))Illegal frame number Error Turn the power off then on again.
03
(task ID : 32(h))No digital signal Error
04 PCI Destination Address Timeout Error Turn the power off then on again.
05 PCI Map Timeout Error
C9 Hard Error
C
Reset Error
CA
(task ID : 0A(hex))Stream Buffer Full Error Turn the power off then on again.
CB Initialize Error
CC Standby Error
CD Command Error
CE Stream Timeout Error
CF Command Timeout Error
D0 Buffer Full Error
D2 Hard Error(Audio Enc.)
D3 Reset Error(Audio Enc.)
D
D4 Initialize Error(Audio Enc.)
D5 Standby Error (Audio Enc.)
D6 Command Error (Audio Enc.)
D7 Command Timeout Error (Audio Enc.) Turn the power off then on again.
DC Hard Error (Video Enc.)
DD Reset Error (Video Enc.)
DE Initialize Error (Video Enc.)
DF Standby Error (Video Enc.)
E0 Command Error (Video Enc.)
E1 DV Decode Error
E
E2 DV Encode Error
E3 FS Change Error (before)
E4 FS Change Error (after)
E5 Command Timeout Error (Video Enc.) Turn the power off then on again.
E6 Command Execute Error (Video Enc.) Turn the power off then on again.
5) Recording data (Page 5)
The internal data on recording are displayed.
6) Application data (Page 6)
The internal data on the application are displayed.
F
Note on the drive error log: The drive error log can be displayed in Test mode.
142
1
2
Error code (last 2 digits)
Task ID (used in some error codes)
Date and time of occurrence
Turn the power off then on again.
As the selected input signal is copy-protected, recording could not be performed.
When this error is generated even if the video signal from the disc created by the PRV-LX1
is to be recorded, replace the AVIB board.
Because no digital signal is input to the selected digital input connectors, recording could not
be performed. When this error is generated even if the digital signal is confirmed to be input
to the DV connectors, etc., replace the AVIB board.
Turn the power off then on again.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Turn the power off then on again.
Turn the power off then on again.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Check wiring or connections. If the problem persists after corrective measures are taken, replace the AVIB board.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
Turn the power off then on again.
PRV-LX10
2
3
Correction Measures
3
4
4