Step 6: Easy Setup; Tel 13942296513 - Sony RDR-GX350 Service Manual

QQ
3 7 63 1515 0
Code numbers of controllable TVs
If more than one code number is listed,
try entering them one at a time until you
find the one that works with your TV.
Manufacturer
Sony
Hitachi
JVC
Panasonic
Philips
Samsung
Sanyo
Thomson
Toshiba
The remote performs the following:
Buttons Operations
TV [/1
Turns your TV on or
off.
TV 2 (volume)
Adjusts the volume
+/– of your TV.
TV PROG +/– Selects the
programme position
on your TV.
TV t (input
Switches your TV's
select) input source.
To operate the TV/DVD button
(for SCART connections only)
The TV/DVD button switches between TV
mode and DVD mode. Press the TV/DVD
button when in stop mode or no menu appears
on the TV screen. Point your remote at the
recorder when using this button.
TV mode: switch to this when you use the
TV's tuner mainly. When you start playback,
the input source for the TV is set to the
recorder automatically. When you press the
x (stop) button during playback, the
programme tuned by the TV or external
equipment appears.
DVD mode: switch to this when you use the
recorder's tuner mainly. When you press the
x (stop) button during playback, the
programme tuned by the recorder appears.
To check the current mode, press DISPLAY
TE
L 13942296513
(page 35).
22
Progressive
When you connect a progressive format
TV to this recorder using the
COMPONENT VIDEO OUT jacks,
select "Compatible."
HDD caution messages
Read the HDD caution messages, and
press ENTER.
4
Select "Finish Setup" using M/m, and
press ENTER.
"Easy Setup" is completed.
To return to the previous step
Press O RETURN.
z Hint
If you want to run "Easy Setup" again, select "Easy
Setup" in the "Basic" setup from "Initial Setup" in
the System Menu (page 110).
Setting up your set top box
receiver for the GUIDE Plus+
system
Follow the steps below to set up your set top
box receiver for the GUIDE Plus+ system.
Note that the OSD language, Clock and
Country are all set for the GUIDE Plus+
system when "Easy Setup" is completed.
1
Press GUIDE.
The GUIDE Plus+ system "Basic Setup"
appears.
www
.
24
http://www.xiaoyu163.com
If you have a Sony DVD player
or more than one Sony DVD
recorder
Code number
If the supplied remote interferes with your
01 (default)
other Sony DVD recorder or player, set the
24
command mode number for this recorder and
the supplied remote to one that differs from
33
the other Sony DVD recorder or player after
17, 49
you have completed "Step 6: Easy Setup."
The default command mode setting for this
06, 08
recorder and the supplied remote is DVD3.
71
You can check the current Command Mode
25 in the front panel display. For details, see
page 127.
43
The default command mode setting for this
38
recorder and the supplied remote is DVD3.
The remote does not function if different
command modes are set for the recorder and
remote. Set the same command mode.
Changing programme positions
of the recorder using the
remote
You can change programme positions of the
recorder using the number buttons.
Number
buttons
ENTER
Example: for channel 50
Press "5," "0," then press ENTER.
2
Select "Postal Code," and press
ENTER.
3
Enter your postal code using </M/m/
,, and press ENTER.
If "Country" is set to "Others," you
cannot enter a postal code and the
GUIDE Plus+ system will not search for
a host channel.
4
Select "External Receiver 1," and
press ENTER.
You can also select "External Receiver
2" or "External Receiver 3" if you have
connected additional set top box
receivers.
5
Press ENTER to select "Continue."
6
Select the set top box receiver type
using M/m, and press ENTER.
7
Select the provider using M/m, and
press ENTER.
8
Select the receiver brand using M/m,
®
and press ENTER.
If you select "Other providers," you can
select a receiver brand from a list of all
available brands.
If your receiver brand is not on the list,
select "???."
The receiver brand list is automatically
updated, so your receiver may be
available at a later date. Select your brand
when it becomes available. Until then,
use "???."
9
Select the connection you used for
your set top box receiver using M/m,
and press ENTER.
When the set top box receiver is
connected to the recorder using hookup
A with both an aerial cable and a SCART
cord, select either "Line1" or "Antenna."
The display asks for confirmation.
10
Press ENTER to select "Continue."
The Video Window switches to the
specified programme position.
x ao
y
i
http://www.xiaoyu163.com
8

Step 6: Easy Setup

Make the basic adjustments by following the
on-screen instructions in "Easy Setup."
Be careful not to disconnect the cables or exit
the "Easy Setup" function during this
procedure.
O RETURN
1
Turn on the recorder and your TV.
Then switch the input selector on your
TV so that the signal from the recorder
appears on your TV screen.
The "Language" display appears.
• If the "Language" display does not
appear, select "Easy Setup" in the
"Basic" setup from "Initial Setup" in
the System Menu (page 110).
2
Select a language for the on-screen
displays using M/m, and press
ENTER.
The initial settings message appears.
3
Select "Start" using M/m, and press
ENTER.
Follow the on-screen instructions to
make the following settings.
Q Q
3 6 7 1 3
11
Select "YES" using M/m, and press
ENTER.
The display asks for confirmation.
If the Video Window does not switch to
the specified programme position, select
"NO" and press ENTER until the Video
Window switches to the specified
programme position.
To receive GUIDE Plus+ system data
your recorder must be turned off
when not in use. If your recorder is
connected to a set top box receiver, be
sure to leave the set top box receiver
turned on. After initial setup, it may
take up to 24 hours to begin receiving
TV programme listings.
b
Note
You cannot set tuner system or "OSD
Language" to a country/region or language
that is not supported by the GUIDE Plus+
system.
If you cannot get the recorder to control
your set top box receiver
Check the connection and position of the set
top box controller (page 14).
If your set top box receiver still does not
operate with this recorder, refer to the
instructions supplied with your set top box
receiver and contact your cable or satellite
company to see if they can provide you with
a compatible set top box receiver.
b
Notes
• The list of external receivers controllable by the
GUIDE Plus+ system is updated constantly and is
distributed through GUIDE Plus+ system data
signals. Since the time your recorder has been
produced and the time you installed your recorder
for the first time, new external receiver codes
might have been added.
• If the external receiver is still not on the list or is
not controlled properly by the recorder, please
call Customer Support to report the brand and
model of your external receiver.
u163
.
1-5
2 9 9 4 2 8
Auto Channel Setting
If you connect a TV to this recorder not
using SMARTLINK, select "Auto
Scan." Then select your country/region
using </,, and press ENTER. The
programme position order will be set
according to the country/region you
select.
If you connect a TV to this recorder with
[/1 SMARTLINK, select "Download from
TV." Then select your country/region
using </,, and press ENTER. The
tuner preset data will be downloaded
from your TV to this recorder. (For
details, refer to the operating instructions
supplied with your TV.)
GUIDE
To skip this setting, select "Do not set."
</M/m/,,
To set the programme positions
ENTER
manually, see page 111.
Clock Setting
Select "Auto" when a programme
position in your local area broadcasts a
time signal. The "Auto Clock Setting"
display appears.
TV [/1
1
Select the programme position of the
station that carries a time signal
using </,.
2 Select "Start" using m, and press
ENTER.
If a clock signal cannot be found,
press O RETURN, and set the
clock manually.
Select "Manual" to set the clock
manually. The "Manual Clock Setting"
display appears.
1
Select the time zone for your area
using </,, and press m.
2
Select "On" if you are now on
summer time, and press ENTER.
3
Set the day, month, year, hour, and
minutes using </M/m/,, and
press ENTER to start the clock.
TV Screen Size (page 122)
If you have a wide-screen TV, select
"Wide (16:9)." If you have a standard
TV, select "Standard (4:3)." This will
determine how "wide-screen" images are
displayed on your TV.
1 5 0 5 8 2 9 9 4
To fix the set top box controller to your set
top box receiver
Once you have confirmed that the set top box
controller controls your set top box receiver,
fix it in place.
1
Remove the backing on the double-sided
tape.
2
Attach it so that the set top box controller
is directly above the remote control
sensor on your set top box receiver.
To change the basic GUIDE Plus+ settings
1
Press GUIDE.
The GUIDE Plus+ system "Home
Screen" appears.
2 Select "Setup" in the Menu Bar using M/
,, and press ENTER.
The GUIDE Plus+ setup menu appears.
3 Select "Basic Setup" using M/m, and
press ENTER.
4
Repeat from step 2 of "Setting up your
set top box receiver for the GUIDE
®
Plus+ system" on page 24.
m
co
9 9
2 8 9 9
,continued
23
25