Scope Of Use; Assembly And Starting - Stanley 8216035SCR011 Instruction Manual

2. LAYOUT (Fig. 1)
1. Shroud
G
2. Pressure vessel
B
3. Wheel
4. Supporting foot
5. Quick-lock coupling (regulated compressed air)
6. Pressure gauge (for reading the preset pressure
by means of regulator)
7. Pressure regulator
8. ON/OFF switch
9. Transportation handle
10. Safety valve
11. Receiver condensation drainage tap
12. Pressure gauge (for reading the tank pressure)
13. Axle
14. Clip

3. SCOPE OF USE

The compressor is designed for generating compressed
air for tools operated by compressed air.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the machine is used
in commercial, trade or industrial businesses or for
equivalent purposes.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user/operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
4. POINTS TO NOTE WHEN SETTING
UP THE COMPRESSOR
● Examine the machine for signs of transit damage.
Report any damage immediately to the company
which delivered the compressor.
● The compressor should be set up near the working
consumer.
● Avoid long air lines and long supply lines (extensions).
● Make sure the intake air is dry and dust-free.
● Do not set up the compressor in damp or wet rooms.
● The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature from
+5°C to +40°C). There must be no dust, acids, vapors,
explosive gases or inflammable gases in the room.
● The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.

5. ASSEMBLY AND STARTING

Warning!
You must fully assemble the appliance before
using it for the first time.
5.1 Fitting the wheels (Fig. 3)
Fit the supplied wheels as shown in Fig. 3:
● Fig. 3a & 3b: Assembly of wheel kit
Assembly by sequence: a, b, c, d, e
5.2 Fitting the supporting foot (ref. 4)
Fit the supplied rubber stopper as shown in Fig. 4.
5.3 Voltage
The compressor is equipped with a mains cable with
shock-proof plug. This can be connected to any 230V
~ 50Hz shock-proof socket which is protected by a 16
A fuse. Before you use the machine, make sure that
the mains voltage complies with the specifications on
the rating plate. Long supply cables, extensions, cable
reels etc. cause a drop in voltage and can impede motor
start-up. In the case of low temperatures below +5°C,
motor start-up is jeopardized as a result of stiffness.
5.3.1 Connection of the mains plug (electrical
information for the BS plug)
Important!
The wires in the mains lead fitted to this product are
coloured in accordance with the code shown in fig. 5.
● This product is double insulated and therefore
does not require a connection to earth.
● The 3 pin plug must comply to BS1363/A.
● Fuse must comply to BS1362.
If for any reason the 13 amp plug fitted to this product
requires replacement it must be wired in accordance
with the following instruction:
Do not connect the brown (live) or blue (neutral)
to the earth pin marked 'E'
Connect the Blue wire to the terminal marked Neutral
(N). Connect the Brown wire to the terminal marked
Live (L). Ensure that the outer insulation is gripped by
the cord grip and that the wires are not trapped when
replacing the plug cover. The mains lead on this product
is fitted with a 13 amp (BS1363/A) plug. A 13 amp
(BS1362) fuse must be fitted in the plug.
If in doubt consult a qualified electrician
There are no user serviceable parts inside this product
except those referred to in the manual. Always refer
8
on the 3 pin plug.