Troubleshooting; Cleaning The Blender - Bosch MUM6N Series Operating Instructions Manual

Cleaning the bowl and tools
Fig. D
`~ìíáçå>
aç=åçí=ïÉÇÖÉ=éä~ëíáÅ=é~êíë=áå=íÜÉ=
ÇáëÜï~ëÜÉêI=~ë=íÜÉó=ÅçìäÇ=ÄÉ=
éÉêã~åÉåíäó=ÇÉÑçêãÉÇ=ÇìêáåÖ=íÜÉ=
ï~ëÜáåÖ=éêçÅÉëëK
Bowl and double whisk are dishwasher-proof.
Dismantle double whisk for cleaning.
– Pull whisks out of the holder.
– After drying the whisks, re-insert them,
ensuring that the gearing meshes fully.
Clean kneading hook with a brush under
running water. If required, use a little washing-
up liquid.
Important information
Before cleaning the bowl in the
dishwasher, take the drive shaft
out of the bowl.

Rotate the bowl and base upwards.

Rotate and remove drive shaft from the fins
in an anti-clockwise direction.

Pull out drive shaft.

After drying the parts, re-insert the drive
shaft.

Lock drive shaft in position by rotating
it in a clockwise direction.

Cleaning the blender

Fig. E
oáëâ=çÑ=áåàìêó=Ñêçã=ëÜ~êé=Ää~ÇÉë
aç=åçí=íçìÅÜ=Ää~ÇÉ=áåëÉêí=ïáíÜ=Ä~êÉ=
Ü~åÇëK=`äÉ~å=íÜÉã=ïáíÜ=~=ÄêìëÜK
`~ìíáçå>
aç=åçí=ìëÉ=~Äê~ëáîÉ=ÅäÉ~åáåÖ=
~ÖÉåíëK
aç=åçí=ÅäÉ~å=Ää~ÇÉ=áåëÉêí=áå=íÜÉ=
ÇáëÜï~ëÜÉêK=aç=åçí=äÉ~îÉ=Ää~ÇÉ=
áåëÉêí=áå=ï~íÉêK
Robert Bosch Hausgeräte GmbH
It is recommended to clean the blender
immediately after use. This will prevent residue
from drying on and attacking the plastic
(e. g. by essential oils in herbs).

Clean blender jug (without blade insert),
lid and funnel in the dishwasher.

Clean blade insert with a brush under
running water. Do not leave in water!
Tip: Pour water with a little washing-up liquid
into the attached blender (approx. half full).
Switch on the blender forseveral seconds
(setting M). Pour out the water and rinse out
the blender with clear water.

Troubleshooting

oáëâ=çÑ=ÉäÉÅíêáÅ=ëÜçÅâ
_ÉÑçêÉ=ïçêâáåÖ=çå=íÜÉ=~ééäá~åÅÉI=
éìää=çìí=íÜÉ=ã~áåë=éäìÖK
Appliance does not start

Check the power supply.

Check the mains plug.

Switch appliance to 0/off and then back
to the required setting.
When using the blender:

Screw the blender on tight as far
as possible.

Attach the blender cover and screw on
as far as possible.
When using the bowl/tools:

Attach protective cover to the blender
drive.
Blender does not start working or stops
during use, the drive is "humming".
The blender blade is blocked by one
of the ingredients.

Switch off the appliance and pull out
the mains plug.

Detach the blender and remove
the obstruction.

Re-attach the blender.

Switch on the appliance.
Important information
If the fault cannot be eliminated,
please contact customer service.
en
11