IMPORTANT–Please Read and Follow! • Make sure that incoming voltage is the same Your safety and the safety of others is as unit rating. An electric rating plate very important. specifying voltage, frequency, wattage, amperage, and phase is attached to the We have provided many important safety messages in this manual and on your product.
Page 4
• The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Specifications Description VCWB301/Standard Mount VCWB301/Flush Mount Overall width 30” (76.2 cm) Overall height from bottom 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. Overall depth from rear To rear edge of side trim: 22-3/16” (56.4 cm) 23-13/16” (60.5 cm) To front of door: 24-1/32”...
Cutout Dimensions 2” x 4” Mounting Board [1-1/2” (3.8 cm) x 3-1/2” (8.9 cm)] Attached to anti-tip mounting bracket Note: If unit is installed deeper than 24” (61.0 cm), then shim behind anti-tip bracket thickness by the same amount 1-1/2” 1-1/2”...
Cabinet Information Professional models fit “semi-flush” in standard 24” (61.0 cm) deep cabinet openings. The door face protrudes 2-1/16” (5.2 cm) from the cabinet face. The handle protrudes an additional 2-1/2” (6.4 cm) into the room. Wall 1-13/16” 3/4” (4.6 cm) (1.9 cm) full end panel...
Page 9
Cabinet Information Professional models fit “semi-flush” in standard 24” (61.0 cm) deep cabinet openings. The door face protrudes 2-1/16” (5.2 cm) from the cabinet face. The handle protrudes an additional 2-1/2” (6.4 cm) into the room. Wall 1-13/16” (4.6 cm) 3/4”...
Page 10
Cabinet Information Wall 1-13/16” 3/4” (4.6 cm) (1.9 cm) space if 24” 24” full end (61.0 cm) (61.0 cm) panel standard cabinet TOP VIEW standard depth is used cabinet depth 2-1/16” (5.2 cm) Partial overlay Door offset cabinet door...
Cabinet Information (with Flush Mount Trim) Professional models with Flush Mount Trim fit “flush” in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except 2-1/2” (6.3 cm) handle depth. Wall 1” 3/4” (2.5 cm) (1.9 cm) full end panel 25”...
Page 12
Cabinet Information (with Flush Mount Trim) Professional models with Flush Mount Trim fit “flush” in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except 2-1/2” (6.3 cm) handle depth. 1” (2.5 cm) space if 25” Wall (63.5 cm) cabinet depth is used 3/4”...
Page 13
Cabinet Information (with Flush Mount Trim) Wall 3/4” (1.9 cm) space if 24” (61.0 cm) standard cabinet depth is used 24” (61.0 cm) TOP VIEW standard cabinet depth 24-3/4” (62.9 cm) Door Wine cellar and Cabinet door cabinet door flush...
Custom Side Panel Dimensions (with Flush Mount Trim) NOTE: Adding a 3/4” (1.9 cm) side panel adds an additional 3/4” (1.9 TOP VIEW cm) to the overall width of the product for each side panel used. Requires 1” Z-Bracket side panel hardware kit (Kit model 3/4”...
IMPORTANT: If the power cord is damaged, must be secured in place with a solid it must be replaced by a Viking qualified soffit or wood block. technician or a Viking Range Corporation representative in order to avoid hazard.
General Information • Most of the unit’s weight is at the top. WARNING Extra care is needed when moving the unit to prevent tipping. TIP OVER HAZARD Appliance is top heavy • Do not remove protective film until unit is and tips easily when in operating position.
Home Security System Connection NOTE: Contact a qualified electrician or authorized agent from alarm company to connect your home security system to the wine cellar. Home security system connection must be hooked up before the unit is installed. 1. Remove the four mounting screws attaching the unit compartment cover to the cabinet. (2 per side) 2.
Securing Your Wine Cellar (3 options) WARNING ELECTRICAL SHOCK HAZARD Disconnect power at breaker or turn power disconnect switch to OFF position before performing any installation procedure. Failure to do so can result in death or electrical shock. OPTION 1 If a solid soffit is 1”...
Page 20
Securing Your Wine Cellar Before moving the wine cellar in place, confirm the finished dimensions, electrical location, minimum door and shelf clearances, and door panel instructions. 1. Position wine cellar in front of cutout. 2. Verify operation by plugging power cord in receptacle.
Kickplate Installation The kickplate consists of a two (2) part assembly: one top louvered panel and one bottom solid panel. Install the kickplate with louvered section on the top. Flooring must allow the kickplate to be removed. To install: 1. Insert the bottom (solid) panel into the open end of the top (louvered) panel. The holes in the bottom panel should line up with the slots in the top panel.
Door Stop/Hinge Adjustment DOOR STOP 1. Using a 3/16” Allen wrench, remove door stop pin located in bottom hinge. 2. The pin is factory set 110°. For 120° swing, move the pin to the utmost forward stop hole. For 90° swing, move the pin to the utmost rear stop hole. HINGE ADJUSTMENT 1.
• Name of dealer from whom purchased Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range, LLC at 1-888-845-4641 or write to:...
Page 24
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 or visit the Viking Web site at vikingrange.com F20904D EN (040116)