FILE NO. SERVICE MANUAL Multimedia Projector Model No. PLc-Wtc500L U.S.A, Canada, Europe, U.K, Asia original Version * Projection lens is optional. chassis No. KV5-Wtc500L00 Match the Chassis No. on the unit's back cover with the Chassis No. in the Service Manual.
Contents SERVICE MANUAL ............1 Fan control stage ............80 Contents ................ 2 Motor control stage ........... 81 Safety Instructions ............3 Bus control stage ............82 Safety Precautions ............. 3 LED drive & RC control stage ........83 Product Safety Notice ..........3 Power supply &...
Safety Instructions Safety Precautions WARNING: The chassis of this projector is isolated (COLD) from AC line by using the converter transformer. Primary side of the converter and lamp power supply unit circuit is connected to the AC line and it is hot, which hot circuit is identified with the line ( ) in the schematic diagram.
Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 17 .8” x 6.9” x. 21.7” (451.0 mm x 175.0 mm x 550.1 mm) Net Weight 32.4 lbs (14.7 kg) Feet Adjustment 0˚ to 3.5˚ Panel Resolution LCD Panel System 0.95” TFT Active Matrix type, 3 panels Panel Resolution 1280 x 800 dots Number of Pixels 3,072,000 (1,280 x 800 x 3 panels) Signal Compatibility Color System PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N High Definition TV Signal 480i, 480p, 575i, 575p, 720p, 1035i, and 1080i Scanning Frequency H-sync. 15 kHz–100 kHz, V-sync. 50 Hz–100 Hz Optical Information Projection Lens Optional Projection Lamp 330 W NSHA(1 lamp + 1 lamp) Interface Input 1 HDMI x 1, Analog (Mini D-sub 15 pin) x 1 Input 2 BNC Type x 5 (G or Video/Y, B or Cb-Pb, R or Cr-Pr, HV and V) Input 3 RCA Type x 1, Mini DIN 4 pin x 1 AUDIO IN Audio 1 (Mini Type stereo), Audio 2 (Mini Type stereo), Audio 3 (RCA Type) x 2...
Circuit Protections This projector provides the following circuit protections to operate in safety. If the abnormality occurs inside the pro- jector, it will automatically turn off by operating one of the following protection circuits. Fuse A fuse is located inside of the projector. When the POWER indicator is not lightning, the fuse may be opened.
Circuit Protections Mechanical sensor switches (SW67A, SW7641) This projector provides 2 mechanical sensor switches, the one is for filter cartridge sensor switch (SW7641) and the other one is for lamp cover sensor switch (SW67A). The filter cartridge sensor switch detects whether the filter cartridge is installed correctly.
Circuit Protections Temperature sensors, wind sensors The projector provides 2 temperature sensor ICs, 1 thermistor, and 1 wind sensor on the intake duct. These devices are monitoring the surrounding temperature of the lamp, panel and intake duct, and the wind sensor is monitoring airflow passed through the air filter in the intake duct.
Circuit Protections Power failure and fan lock detection The projector provides the detection circuits of the power failure and the fan lock. When the detection circuit detects an error at the power supply line or at the fan operation circuit, the projector will turn into the standby mode to protect the other circuits defective.
Maintenance Replacing the Filter Cartridge Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter becomes clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup and adversely affect the life of the projector.
Maintenance Resetting the Filter Counter Be sure to reset the Filter counter after replacing the filter Filter counter cartridge. Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame point- er to the Setting Menu icon.
Maintenance Lamp Selection System This Projector is equipped with 2 Projection Lamps. The Lamp Management Function detects the status of lamps and shows the status on screen or on the LAMP 1/2 REPLACE indicators. This function also automatically controls the Lamp Mode when any of lamps reaches the recommended total hours of use or is out for the end of life or mal- functions.
Maintenance Lamp Replacement When the total lighting time of a Projection Lamp reaches the Top Control recommended total hours of use, the Lamp replacement icon appears on the screen and LAMP 1 / 2 REPLACE indicator Lamp replacement icon lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP 1 / 2 REPLACE indicator should light LAMP 1/2 rePLAce is depending on the lamp mode.
Maintenance How to check Lamp Used Time The LAMP REPLACE indicator will light yellow when the total lamp used time (Corresponding value) reaches 3,000 hours. This is to indicate that lamp replacement is required. The total lamp used time is calculated by using the below expression, Total lamp used time (Corresponding value) = eco + ( normal x 1.2) + (...
Maintenance Cleaning After long periods of use, dust and other particles will accumulate on the LCD panel, prism, mirror, polarized glass, lens, etc., causing the picture to darken or color to blur. If this occurs, clean the inside of optical unit. Remove dust and other particles using air spray.
Maintenance Quick maintenance This projector provides a cabinet prism cover on the cabinet top to enhance the service maintenance. This enables service personnel to align the optical adjustment or replace the optical parts without disassembly the cabinet top. Loosen a screw-A on the lamp cover and slide it backward, and then loosen a screw-B on the prism cover and turn it up in the arrow direction (Fig.
Maintenance Lens Installation When replacing the lens or using an optional lens, install the lens by following the instructions below. removing the lens Lens Release button Shift the lens to the center position by using the Lens shift function. Turn off the projector and unplug the AC power cord.
Maintenance Using the Lens Antitheft screw This projector provides a Lens antitheft screw to protect the projection lens stolen from a suspicious person. Mount the Lens antitheft screw by following the instructions below. Mounting the Lens antitheft screw Loosen a screw-A on the lamp cover and slide it backward, and then loosen a screw-B on the prism cover and turn it up in the arrow direction (Fig.
Security Function Notice This projector provides security functions such as "Key lock", "PIN code lock" and "Logo PIN code lock". When the projector has set these security function on, you are required to enter correct PIN code to use the projector. If you do not know the correct PIN code to the projector, the projector can no longer be operated or started.
Mechanical Disassembly Mechanical disassembly flow chart Mechanical disassembly should be made by following procedures chart. Screws Expression Following steps show the basic procedures, therefore unnecessary step may (Type ) mm Diameter x Length be ignored. T type M Type Caution: The parts and screws should be placed exactly the same position as the original otherwise it may cause loss of performance and product safety.
Page 20
Mechanical Disassembly Mechanical disassembly 1-1. Cabinet Top removal-1 1. While pressing the Lens release button on the top of the cabinet, turn the lens counterclockwise until it stops and pull it out slowly from the projec- tor. 2. Remove the terminal covers. See the items "Lens installation"...
Page 21
Mechanical Disassembly 1-3. Prism Cover removal 1. Loosen 1 screw-D and slide the Lamp Cover backward. 2. Loosen 1 screw-E and turn the Prism Cover up and pull it upward to re- move. (Press the 2 places to unhook the hinges.) Lamp cover Prism cover Hinges...
Mechanical Disassembly 1-5 Lamp Cover removal 1. Remove 4 screws-F (T3x6) on each hinge holder and remove Lamp Cover. Lamp cover Hinge Shield plate holder t3x6 Shield plate t3x6 1-6. Control Board removal 1. Remove the Control Board and Button. Button LED decoration Spacer...
Page 23
Mechanical Disassembly 2-1. Main Board removal-1 1. Remove 6 screws-A (M3x6) and 7 screws-B (M3x6). 2. Remove the Main Shield Top, Lamp Shield and Mirror Shield. Mirror shield Main shield Lamp shield Spacer 2-2. Main Board removal-2 1. Remove 2 screws-C (M3x6) on the AV panel and take out the Main Board upward off.
Page 24
Mechanical Disassembly 3-1. Audio, Panel Temp, Rear Junction, R/C Rear Board re- moval 1. Remove 2 screws-A(T3x8) and take off the Audio Board upward. 2. Unhook and slide the Panel Temp Sensor Board to remove. 3. Remove 2 screws-B (M3x6) and take off the Rear Junction Board. 4.
Page 25
Mechanical Disassembly 4-1. Filter Box Assy and Fans removal 1. Remove 4 screws-A (T3x8) and 1 screw-B(M3x6) and take the Filter Box Assy upward off. 2. Remove 2 screws-C (T3x10) and pull the Fans Assy upward off. M3x8 FN904 Filter cartridge M3x8 M3x8 Filter box assy...
Page 26
Mechanical Disassembly 5-1. A/V Board Assy removal 1. Remove 3 screws-A (M3x6) and take the AV Board Assy upward off. A/V board t3x8 t3x8 t3x8 M3x12 R/C Front & Top board M3x5 t3x15 (black) A/V board assy 6-1. Network Joint Board Assy removal 1.
Page 27
Mechanical Disassembly 7-1. Power Board Assy removal 1. Remove 7 screws-A (M3x6) on the Power Box Top Cover and remove the top cover. 2. Remove 2 screws-B (M3x6) and remove the Power Board Assy. Power box top cover Power board assy M3x8 Power board Isolation sheet...
Page 28
Mechanical Disassembly 7-3. Ballast Board removal 1. Remove 2 screws-D (M3x6) and 1 screw-E (T3x10) and remove the Lens shift shield side and Ballast Boars assy. (To remove the Ballast Board Assy, first remove the Lamp and remove 2 screws on the Lamp Holder and move the Lamp Holder upward slightly and then take off the Ballast Board Assy.) 2.
Page 29
Mechanical Disassembly 8-1. Rear Fans Assy removal-1 1. Remove 1 screw-A (M3x6) and 1 screw-B (T3x8). 2. Remove 1 screw-C (T2.6x8) and remove the Thermal Protector (SW902) and then remove the Side Shield Plate. thermal protector (SW902) removal Thermal t2.6x8 protector (SW902) Side shield...
Page 30
Mechanical Disassembly 9-1. Optical Unit Assy removal-1 1. Remove both of the Lamp Assy upward. 2. Remove 2 screws-A (T3x8) each on the Lamp Duct. Lamp2 Lamp1 9-2. Optical Unit Assy removal-2 1. Remove 1 screw-B (T3x8) each on the Lamp Socket and remove them. 2.
Page 31
Mechanical Disassembly 9-3. Optical Unit Assy removal-3 1. Remove 2 screws-E (T3x8) each on the Lamp Cover. Pull up the Lamp Covers. (Note: Pay attention to fix the lamp covers mounting direction. The location of the metal plates) Lamp2 cover Metal plate Lamp1...
Optical Parts Disassembly Before taking these procedures, remove the cabinet top, Main board assy, shutter assy, lamp covers assy referring to the chapter "Mechanical Disassembly". 1-1. LCD Panel/Prism Assy removal 1. Loosen 3 screws-A (M2.5) and pull up the Panel/Prism assy. -34-...
Page 35
Optical Parts Disassembly Lcd Panel type check There are 2 types combination of the LCD panel/prism assembly and the optical unit, named Type-R and Type-L. Since both have no compatibility, each type should be combined with the same type, and the specific parts should be used.
Page 36
Optical Parts Disassembly 1-2. LCD Panel/Prism Assy disassembly 1. Remove 1 screw-A (M2x4) each on the stopper and remove the stopper-B and C, and pull the Polarized Glass-Out and Pre-Polarized Glass upward. There is a single-glass type or a double-glass type for the double-glass type structure the Polarized Glass (G).
Page 37
Optical Parts Disassembly Mounting direction Mount the pre-polarized glasses and polarized glasses as shown in the figure below. Lcd panel/Prism top view (Polarized Glass: Single-glass type) Film side Film side Blue Marker Red Marker R-LCD panel B-LCD panel Prism Blue Marker Film side Green Marker Single-glass type...
Page 38
Optical Parts Disassembly 2-1. Polarized Glass-in/Optical Filter removal 1. Remove 2 screws-A (M2.5x5) and remove the stoppers, and pull the Polar- ized Glass and Pre-Polarized Glass Holder upward. Polarized glass- in/Optical filter ass'y Glass holder Stopper Glass holder film Polarized glass (in) Optical filter (ICV) Prism side Blue...
Page 39
Optical Parts Disassembly 2-2. Polarized Glass-in/Optical Filter mounting There are 2 types combination of the LCD panel/prism assembly named Type-R and Type-L. Mount the polarized glasses and optical filters according to the type of the LCD panel assembly as shown in the figure below tYPe-L Blue Green...
Page 40
Optical Parts Disassembly 3-1. Relay Lens Assy removal 1. Remove 1 screw-A (M2.5x5) and slide the Relay Lens assy in the arrow direction and pull it up to remove. t3x8 Relay lens assy Spacer Relay lens Relay lens assy -40-...
Optical Parts Disassembly 4-1. Condenser Lens Assy removal 1. Remove 2 screws-A (M2.5x5) and slide the Condenser Lens Assy in the arrow direction and pull it up. t3x8 Condenser lens Spacer Condenser lens Condenser lens assy -41-...
Optical Parts Disassembly 5-1. Mirror Assy removal 1. Remove 4 screws-A (T3x10) and take the Mirror Cover off. 2. Remove 3 screws-B (M3x18) and pull the Mirror Assy upward. Note: Turn the mirror holder counterclockwise with a flat screw driver if the screw is behind a mirror holder.
Page 43
Optical Parts Disassembly 6-1. Optical Parts in the Optical Unit removal 1. Remove 2 screws-A (T3x10) and unhook 4 hooks-B and take the Optical Unit Top off. Condenser lens(R) Polarized glass(IN/GB) Condenser lens(B) Mirror(R) Mirror(B) Condenser lens(G) Relay lens(In) Dichroic mirror(B) Dichroic mirror(G) Mirror(R) Integrator lens(Out)
Page 44
Optical Parts Disassembly 6-2. Optical Parts Directions in the Optical Unit When mounting or assembling the optical parts in the optical unit, the parts must be mounted in the specified location and direction as shown in the figure below. Polarized glass (IN/GB) dichroic mirror Place glasses as the marker comes top-left corner as Place the dichroic mirrors as the marker comes top...
Adjustment Service Adjustment Menu Operation to enter the service mode To enter the “Service Mode”, press and hold the MeNu and SeLect button for more than 3 seconds. The service menu appears on the screen as follows. to adjust service data Select the adjustment group no.
Optical Adjustment WArNING : uSe uV rAdIAtIoN eYe ANd SKIN ProtectIoN durING SerVIcING cAutIoN: to prevent suffer of uV radiation, those adjustments must be completed within 25 minutes. Before Adjustment Each adjustment requires hex wrenches and slot screw- drivers. The adjustments require long handle type tools because of not removing the main board.
Optical Adjustment 1. Optical axis adjustment Select the internal test pattern signal “All white” from the projector’s menu “Menu -> Setting -> Test pattern”. 1-1. condenser lens adjustment Loosen 2 screws and 2 screws Move the condenser lens to display the color shading on the top/bottom and left/right of the screen.
Optical Adjustment 1-2. relay lens adjustment Loosen 1 screw and 1 screws Move the Relay lens so that the color shading appeared on the top/bottom and left/right of the screen becomes the same width. 1) Insert a slot driver into the slot and turn it to move the image horizon- tally as shown in Fig.1-3, 2) Insert a slot driver into the slot...
Page 50
Optical Adjustment 1-3. condenser lens adjustment-2 Move the condenser lens to remove the color shading on the top/bottom or left/right of the screen. 1) Insert a slot driver into the slot and turn it to move the image horizon- tally as shown in Fig.1-5. 2) Insert a slot driver into the slot and turn it to move the image vertically as shown in Fig.1-6.
Optical Adjustment 2. Mirror adjustment Input the 100%-white pattern with WXGA computer signal. Enter the service mode. Select Group "236", No. "0". Group No data Function Change the data value to "1". The lamp mode changes to "Lamp1" and the Normal mode mirror motor starts turning continuously.
Optical Adjustment 3. Contrast adjustment Select the internal test pattern signal “All black” from the projector’s menu “Menu -> Setting -> Test pattern”. Loosen 2 screws on the glass holders for G-panel. Turn the lever of polarized glass to obtain the darkest brightness and proper black color uniformity on the screen.
Electrical Adjustments Circuit Adjustments CAUTION: The each circuit has been made by the fine adjustment at factory. Do not attempt to adjust the following adjustments except requiring the readjustments in servicing otherwise it may cause loss of performance and product safety. Before taking these adjustments, turn the projector for more than 10 minutes to sta- bilize the operation.
Page 54
Electrical Adjustment z Fan Voltages adjustment c Component Auto calibration Equipment Digital voltmeter Input mode Video mode (Input 2 -Component) Input signal 100% color bar signal (480i) 1. Enter the service mode. 100% color bar signal (480p) 2. Adjust the voltage on each test point by changing the 100% color bar signal (720p) data values of the Group - No.
Page 55
Electrical Adjustment PC, Video, Component Manual adjustment When the PC, Video or Component Auto Calibration [2] Manual adjustment (component) fails, take the following manual adjustment instead of Input mode Video mode (Input 2 -Component) auto calibration. Input signal 100% color bar signal (480i) 100% color bar signal (480p) [1] Manual adjustment (Pc) 100% color bar signal (720p)
Electrical Adjustment b Common Voltage adjustment , Gamma shipment adjustment Input mode Computer mode (Input 1 RGB) Software PROJECTOR SERVICE TOOL v4.20 Input signal 50%-RGB pattern computer signals or 16-step gray scale computer sig- Use the software to obtain the proper gray scale. See the further information of the software instruction manual.
Electrical Adjustment Service Adjustment Data Table These initial values are the reference data written from the CPU ROM to memory IC when replaced new memory IC. The adjustment items indicated with “✻” are required to readjust fol- lowing to the “Electrical adjustments”. Other items should be used with the initial data value.
Page 59
Electrical Adjustment Grp / No. Item Function Range Initial Note Noise Region 2 <NSREGIONY2> / <NSREGIONUV2> 0 - 1023 Noise Gain Level <NSFILTERY**> / <NSFILTERUV**> 0 - 255 2:2pull down setting 22Film Mode Sensitivity Film Detection Sensitivity <FILMSTVT22> 1 - 5 22Film Mode Threshold Low <FILMTHRD22A>...
Page 60
Electrical Adjustment Grp / No. Item Function Range Initial Note 101 REGISTER_STATUS Read only 102 FAN1_DET Read only 103 FAN2_DET Read only 104 FAN3_DET Read only 105 FAN4_DET Read only 106 FAN5_DET Read only 107 FAN6_DET Read only 108 FAN7_DET Read only 109 FAN8_DET Read only...
Page 68
Electrical Adjustment Grp / No. Item Function Range Initial Note Temp B Warning (Eco) Temp B (Lamp) to judge the Temp Error at Eco 30-100 Temp C Warning (Eco) Temp C (Panel) to judge the Temp Error at Eco 30-100 Temp B-A Warning (Eco) Temp B - A (Filter Clogged) to judge the Temp Error at Eco 0-100...
Page 69
Electrical Adjustment Grp / No. Item Function Range Initial Note Fan3 Initial Volt 0-255 Fan4 Initial Volt 0-255 Fan Start Voltage (0.1V) Fan5 Initial Volt 0-255 Fan6-8 Initial Volt 0-4095 1845 Cooling Time Cooling Time Setting (x30 sec.) 1: 30 3: 90 15: 450 1-15 Cooling Time Setting When the Temp Error occurs (x30 sec.) Temp Error Cooling Time...
Page 70
Electrical Adjustment Grp / No. Item Function Range Initial Note Auto Calibration (Common) * Auto calibration Execute Calibration when the Value is changed to 1. (For PC Execute Calibration 0 - 1 White 100%) Loop Count Max Times of Calibration 1 - 30 Calibration Log (Read only) Auto Status...
Page 71
Electrical Adjustment Grp / No. Item Function Range Initial Note Closed Caption Caption Mode Caption Mode Select 0: OFF 1: CC1 2: CC2 3: CC3 4: CC4 Color Mode Color Mode 0: Follow to transmit Data 1: Fixed Composite (NTSC) Composite / S-Video Disp Dots 0 - 4095...
Page 72
Electrical Adjustment Grp / No. Item Function Range Initial Note V Back Porch 0 - 4095 Disp Line 0 - 4095 Clamp 0 - 255 Clamp Width 0 - 255 (SUB) H Back Porch 0 - 4095 (SUB) V Back Porch 0 - 4095 (SUB) Clamp 0 - 4095...
Page 73
Electrical Adjustment Grp / No. Item Function Range Initial Note (SUB) V Back Porch 0 - 4095 (SUB) Clamp 0 - 4095 (SUB) Clamp Witdh 0 - 4095 YCbCr (1035i) Total Dots 0 - 4095 2200 Disp Dots 0 - 4095 1874 H Back Porch 0 - 4095...
Page 74
Electrical Adjustment Grp / No. Item Function Range Initial Note Total Dots 0 - 4095 1650 Disp Dots 0 - 4095 1248 H Back Porch 0 - 4095 V Back Porch 0 - 4095 Disp Line 0 - 4095 Clamp 0 - 255 Clamp Width 0 - 255...
Page 75
Electrical Adjustment Grp / No. Item Function Range Initial Note Clamp 0 - 255 Clamp Width 0 - 255 (SUB) H Back Porch 0 - 4095 (SUB) V Back Porch 0 - 4095 (SUB) Clamp 0 - 4095 (SUB) Clamp Witdh 0 - 4095 RGB Video (1080P - 25) Total Dots...
Chassis Description Indicators and Projector Condition Check the indicators for the projector condition. The projector is operating normally. Indicators Projector condition LAMP 1/2 WARNING WARNING POWER SHUTTER REP . TEMP . FILTER blue green / red orange yellow The projector is off. (The AC power cord is unplugged.) The projector is in stand-by mode.
Page 87
Chassis Description the projector is detecting abnormal condition. Indicators Projector Condition LAMP 1/2 WARNING WARNING POWER SHUTTER REP . TEMP . FILTER blue green / red orange yellow The temperature inside the projector is elevated close to the ✽ ✽ ✽ abnormally high level.
Page 88
Chassis Description the projector is detecting abnormal condition. Indicators Projector Condition LAMP 1/2 WARNING WARNING POWER SHUTTER REP . TEMP . FILTER blue green / red orange yellow If the Filter counter reached a time set in the timer setting, ✽ ✽...
Chassis Description Power failure detection system detection of Power failure Projector provides a protection circuit to prevent the secondary failure when the power failure, fans failure or tem- perature failure occurs on the projector. The power failure detection lines "P-FAIL_S5V", "P-FAIL_S3.3V", etc. are connected to the main power supplies.
Chassis Description Error Log This projector provides the error history log function. To Item Data Group (Error Code) check the logs, you need to enter the service mode and <- Latest Error select Group No. "220" and Item No. "0" to "49". The error ✻...
Chassis Description Diagnosis of Power Failure with RS-232C port This projector provides a function to get the error information of the projector by using the RS-232C serial port for the power failure diagnosis. The further error information of the power failure and fan failure can be found out by using this function. Diagnosis procedure Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC.
Chassis Description Serial Control Interface This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Operation Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC. Launch a communication software "Hyper terminal"...
Chassis Description Status read command Format The command is sent from PC to the projector with the format below; 'CR' [Command] 'CR' Command: one character (refer to the command table below. The projector decodes the command and returns the 'Character string' with the format below; command Function Projector return...
Control Port Functions System Control I/O Port Functions (PW392, IC301) PORT SIGNAL FUNCTION NOTE ID_2_PWR_SW Lamp ID 2 Switch PW_SDA3 IIC Bus SDA3 PGC_PW PIC IC Configration FAN_DRIVE _2 Fan Drive 2 HDMI1DCT FAN_DRIVE_1 Fan Drive 1 PIC_PROG PIC IC ID_1_PWR_SW Lamp ID 1 Switch PW_SCL3...
Page 97
Control Port Functions PORT SIGNAL FUNCTION NOTE AH21 KEY2 Key Control Input 2 AH22 PRESS_SENS Pressure Sensor Input AJ20 OPTION3 Option AJ21 KEY1 Key Control Input 1 AJ22 THERM_DET Thermal Sensor Detection (Thermistor/Thermal Sensor IC) AJ23 PW_DAC Not used AK20 THERM1 Thermal Sensor Input AK21...
Page 98
Control Port Functions I/O Expander (M62320, IC5082) PORT SIGNAL FUNCTION NOTE SW_PF5V Power Faiiler Detection Switch P-FAIL_1.2V_HDMI Power Faiiler Detection Input [HDMI 1.2V] H: Normal P-FAIL_RLY Power Faiiler Detection Input [Relay] H: Normal P-FAIL_3.3 Power Faiiler Detection Input [3.3V] H: Normal P-FAIL_5V Power Faiiler Detection Input [5V] H: Normal...
KV5-WTC500L00 Parts Location Diagrams Cabinet front and top assembly A810 CONTROL BOARD Cabinet bottom assembly TH901 FN907 FN906 FN908 SP901 SP902 A1100 AUDIO BOARD -107-...
Page 112
KV5-WTC500L00 Parts Location Diagrams Panel/Prism assembly L01L L01R * A double-glass type (L01-G2a) or a single-glass type (L01-G2b) is used for the Polarized Glass(G). Must be used with the same type of the polarized glass when the replacement. It is no compatibility L01-G2b between a single-glass type and a double-glass type.
Page 113
KV5-WTC500L00 Parts Location Diagrams Polarized-in & optical filter assembly L03-G L03-B L02-G L02-B L02-R L03-R Note: The mounting direction of parts L02 differs according to type of LCD panel/prism assembly. See the item "Optical Parts Disassembly". -113-...
Page 116
KV5-WTC500L00 Parts Location Diagrams ● In the optical unit L04-B L04-G -116-...
Page 117
KV5-WTC500L00 Parts Location Diagrams ● Accessories (see accessories parts list) REMOTE CONTROL MANUALs CD-ROMs VGA CABLE AC CORD AC CORD HOLDER ANTI-THEFT SCREW -117-...
KV5-WTC500L00 Electrical Parts List Product safety should be considered when a component replacement is made in any area of a projector. Components indicated by a mark in this parts list and the circuit diagram show components whose value have special significance to product safety.
Diagrams & Drawings Schematic Diagrams Printed Wiring Board Drawings Model Chassis No. PLC-WTC500L KV5-WTC500L00 these schematic diagrams and printed wiring board drawings are part of the service manual original for chassis No. KV5-Wtc500L00 model PLc- Wtc500L. File with the service manual No. SM5111082-00...
KV5-WTC500L00 Parts description and reading in schematic diagram 1. The parts specification of resistors, capacitors and resistor reading coils are expressed in designated code. Please check Example 1/2 D J 10K B the parts description by the following code table. 2.
SW902 SW901 Schematic S40B0150N S40B0150N SW902B EP42P-100 SW902B SW901B EP42P-100 SW901B CONTROL 81M81K5R0 81M81K5R0 81M81K5R0 81M81K5R0 NETWORK JOINT SS5V_LED Diagrams FOR LP902 FOR LP901 THERMAL PROTECTOR SHUTTER THERMAL PROTECTOR (Blue) S3.3V_PW A902 D2857 (SET TO OPEN AT 100+/-5°C) SMLE12BC7TG SW6803 (SET TO OPEN AT 100+/-5°C) DOWN S10B3530G...
Printed Wiring Board Diagrams ! cAutIoN This projector is isolated from AC line by using the internal converter transformer. Please pay attention to the following notes in servicing 1. Do not touch the part on hot side (primary circuit) or both parts on hot and cold coNtroL (SIde:A) sides (secondary circuit) at the same time.
Note on Soldering do not use solder containing lead. Solder This product has been manufactured using lead-free Use solder with the metal content and composition ratio solder in order to help preserve the environment. by weight given in the table below. Do not use solders Because of this, be sure to use lead-free solder which do not meet these conditions.