Fuel Filter - Stiga TAN 540 D Instructions For Use Manual

stamped" service log is a valuable document that
improves the machine's second-hand value.
The service points are given in the table below. De-
scriptions of how the procedures are to be carried
out are given after the table.
6.2 SERVICE POINTS
1st time Interval
Service point
Hours of operation/
Water separator,
check
Pre-filter, cleaning
Fuel filter, replace
Tyre pressure,
check, adjust
Engine oil, filter,
change
Hydraulic oil, filter,
tank vent valve,
change/clean
Wheel motors ,
change oil
Belt transmissions,
check
Cooling system,
clean
Battery, check
Air filter, clean pre-
filter
Air filter, change
inner filter
Lubrication
Adjusting valves
Grinding valves
6.3 PREPARATION
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by
always applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by removing the ignition key.
6.4 WATER SEPARATOR
There is a float in the water separator (12, 13:C3)
that can be viewed through the transparent cup.
The float must be at the bottom. If the float has ris-
en, the water separator must be drained as follows:
.
See
para-
graph
Calendar months
50/- 6.4
6.4
400/- 6.5
6.6
50/12 200/12 6.7
50/12 400/12 6.8
50/12 200/12 6.9
50 200/- 6.10
1000/12 6.11
50/- 6.12
250/- 6.13
250/- 6.13
6.14
1000/- 6.15
2000/- 6.15
Original instructions for use
ENGLISH
6.4.1 540
1. Shut off the water separator tap. See fig. 12.
2. Hold a container under the water separator to
collect fuel.
3. Open the cup by pressing its ring (12:C1).
4. Carefully remove the cup (12:C2) and remove
the spring, (12:C4) and float (12:C3) from the
cup.
5. Clean the inside of the cup and thread filter
(12:C5).
6. Check that the O-ring is intact and reinstall the
components in reverse order.
7. Open the tap.
Clean the fuel tank if water accumulates in the wa-
ter separator often. Contact an authorised work-
shop.
6.4.2 740
To drain the water unscrew the drain tap (13:C1)
until the water begins to run. Drain until the float
sits at the bottom again.
Clean the separator if the it looks dirty or if it has
to be drained often. The separator is cleaned as fol-
lows:
1. Shut off the water separator tap. See fig. 13.
2. Hold a container under the water separator to
collect fuel.
3. Unscrew the cup. (13:C2).
4. Carefully remove the cup and remove the
thread filter (13:C5), the insert (13:C4), and the
float (13:C3) from the cup.
5. Clean the inside of the cup and thread filter.
6. Check that the O-ring is intact and reinstall the
components in reverse order.
7. Open the tap.
Clean the fuel tank if water still often accumulates
in the water separator. Contact an authorised work-
shop.

6.5 FUEL FILTER

6.5.1 540
1. Shut off the fuel filter's tap. See fig. 14.
2. Hold a container under the fuel filter to collect
fuel.
3. Detach the cup by turning its ring (14:E1).
4. Carefully remove the cup (14:E2) and remove
the filter (14:E4).
5. Clean the inside of the cup.
6. Check that the O-ring (14:E3) is intact and rein-
stall the components with new filter in reverse
order.
7. Open the tap.
8. Bleed the fuel system. See 5.12.
EN
89