Related Manuals for Cosmo COS-HZ5230
Summary of Contents for Cosmo COS-HZ5230
- Page 1 IMPORTANT SAFETY INSTRUCTIONS Carefully read the following Important information redarding installation safety and maintenance. Keep these instruction for future reference.
- Page 2 USERS OPERATING INSTRUCTIONS l INSTALLATION ADVICE IMPORTANT - PLEASE READ AND FOLLOW ü Before using this appliance please read these instructions carefully. ü Do not remove permanently affixed labels, warnings, or plates from the product. This may invalidate the warranty. ü...
-
Page 3: User Instruction
USER INSTRUCTION IMPORTANT PRECAUTIONS AND RECOMMENDATIONS l After having unpacked the appliance, check to ensure that it is not damaged. If you have any doubts, do not use it and consult your supplier or a qualified technician. l Packing materials (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should not be left around within easy reach of children, as these may cause serious injuries. - Page 4 FEATURES L34in x W20in L23.5in x W20in L23.5in x W20in L31in x W17.7in L31in x W17.7in (L34in x W20in) Fig.1.1 Note: -The electric gas-lighting device is incorporated into the knobs. COOKING POINTS CAUTION: If the burner flames are accidentally extinguished, turn the gas off at the control 1.Auxiliary(A) knob and wait at least 1 minute before attempting to relight.
- Page 5 ‚ USING THE GAS COOKTOPS GAS BURNERS Gas flow to the burners are adjusted by turning the knobs(illustrated in (fig.2.1) which control the valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves to following functions: =closed valve =maximum rate =minimum rate...
-
Page 6: Cleaning And Maintenance
CLEANING AND MAINTENANCE ƒ GENERAL RECOMANDATION ü Before you begin cleaning you must ensure that the hob is switched off. It is advisable to clean when the appliance is cold. Do not use steam jet cleaners ü All enamel surfaces have to be washed with soapy water or some because the humidity could other non-abrasive product with a sponge and are to be dried preferably enter into the appliance... - Page 7 NOTE: This is extremely important! Please check before planning for service. CORRECT REPLACEMENT OF THE BURNERS It is very important to check that the burner flame spreader "F" and the cap "C" have been correctly positioned (see figs. 3.1 and 3.2). Failure to do so can cause serious problems.
-
Page 8: Installation Instructions
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustments, alterations, service or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. Screwdriver T-handle wrench Wrench Tape measure Adjustable pliers Adjustable wrench... -
Page 9: General Information
GENERAL INFORMATION The installer must refer to local/national codes 1. Installation must conform with local codes or in 12.Gas Manifold Pressure the absence of local codes, with the National Fuel Natural gas - 5" W.C.P. Gas Code, ANSI Z223.1 -Latest Edition. LP/Propane - 10"... - Page 10 ! INSTALLATION INTO THE CABINET Please take the cut-out size according to the cooktops dimension. 17.7” 31” 34” 20” 2.83” min 1.8” 29” 33” 16.1” 18.9” 21.3” 21.3” min 2” min 2” min 1.6” min 1.6” 23.6” 20” 2.83” 22” 18.9”...
- Page 11 PROXIMITY TO SIDE CABINETS Important: Base cabinet construction must allow for size of cooktops cut-out. 1. Gas line opening: Wall-anywhere 11” 51/64(300mm) below underside of countertop; Cabinet floor – anywhere 3”1/8(79.2mm) from the rear wall. Grounded outlet: the electric cord with 3-prong ground plug has a length of 48”(122mm).Grounded outlet should be located within 36”(914.4mm) of right rear corner of cut-out.
-
Page 12: Gas Connections
⑤ GAS CONNECTIONS All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to the action of LP/Propane gas. - Page 13 GAS CONNECTION SPECIFICATION...
-
Page 14: Leak Testing
b) Any conversion required must be performed a qualified licensed gas service company. Please provide the service person with this manual before work is started on the cooktops. (Gas conversions are the responsibility of the dealer or end user.) c) This cooktops can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with LPG gas. - Page 15 CONVERSION TO LP/PROPANE GAS Every cooktops is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the table below. The nozzle diameters, expressed in hundredths of a millimeter, are marked on the body of each injector. SETTING THE PRESSURE REGULATOR (Fig.
- Page 16 OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS l Remove the gratings, the burner covers and the knobs; l Using a wrench substitute the nozzle injectors “J”(fig:5.4-5.5) With those most suitable for the kind of gas for which it is to Be used.
-
Page 17: Electrical Connection
⑥ ELECTRICAL CONNECTION If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Check with a qualified electrician if you are not sure whether the cooktops is properly grounded. - Page 18 WIRING DIAGRAM IGNITION...
Need help?
Do you have a question about the COS-HZ5230 and is the answer not in the manual?
Questions and answers