Download
Share
Print this page
Genexis DRG700 Quick Installation Manual
  1. Manuals
  2. Brands
  3. Genexis Manuals
  4. Modem
  5. DRG700
  6. Quick installation manual
Genexis DRG700 Quick Installation Manual

Genexis DRG700 Quick Installation Manual

Hide thumbs Also See for DRG700:

Advertisement

Quick Links

See also: User Manual
DRG700
Quick Installation Guide
This guide applies to all DRG700 models

Advertisement

loading

Related Manuals for Genexis DRG700

Summary of Contents for Genexis DRG700

  • Page 1 DRG700 Quick Installation Guide This guide applies to all DRG700 models...

  • Page 2: Table Of Contents

    Contents DRG700 overview......Installation........Network setup......... Wireless setup......... Configuring your DRG700....Troubleshooting......

  • Page 3: Drg700 Overview

    Cleaning instructions: Your DRG700 product may be cleaned using a soft, dry cloth. For areas of persistent dirt, a damp cloth may be used with mild detergent. Product and LED logos may be damaged by using aggressive cleaning products or ethanol-based cleaners - if in doubt do not clean near these logos.
  • Page 4 WLAN enabled WPS button: Blink WPS active WLAN disabled This button is used to automatically connect a WPS-enabled wireless client to the DRG700. For On (green) Link operating at 1000 details about the connection procedure, see ports Mbps “Wireless Setup” on page 8.

  • Page 5: Installation

    Step 3: Mounting the DRG700 on the DRG FTU Remove the dust cover from the DRG FTU. Place the DRG700 on the FTU in such as way that the tabs on side of DRG700 are aligned with the cutouts on the FTU.
  • Page 6 Connect the 12V plug of the supplied adapter to the Connect your computer to one of the Ethernet LAN DRG700 and connect the adapter to a power socket. ports on the DRG700 using an Ethernet cable with a RJ-45 connector. Result: The LED first flashes green.
  • Page 7 Step 6: Connecting your telephone Step 7: Connecting your analog television This step is only relevant if the DRG700 has This step is only relevant if the DRG700 has a CATV telephony ports. connector. Connect a standard telephone handset a telephony Connect your television to the CATV connector using port using a RJ-11 cable.

  • Page 8: Network Setup

    3. Network setup Step 1: Step 3: Open your web browser and check if your Internet Open your web browser and check if the network connection is working. If your connection is working, connection is working. If your connection is not you may skip step 2 and 3.

  • Page 9: Wireless Setup

    They are also Wireless setup using WPA encryption key printed on the label on the back of the DRG700. You can change the SSID and the WPA key when you Step 1: configure the DRG700.

  • Page 10: Configuring Your Drg700

    5. Configuring your DRG700 It is only advised for advanced users to change Step 1: the configuration, as doing this might interrupt Launch the web browser on your computer and your connection. By default the router is enter “http://router” in the address bar. The configured properly for most home networks.

  • Page 11: Troubleshooting

    Action LED is off Make sure you have connected the DRG700 to a working power outlet, using the adapter shipped along with the DRG700. If the LED remains off, please contact your service provider. Red LED is on System error. Disconnect the power from the DRG700 and restart DRG700.
  • Page 12 Europe-EU Declaration of Conformity Hereby, Genexis BV declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Copyright © Genexis BV 2014 rev.1...