General Bits - Siemens SINUMERIK 840C Installation Manual

1 NC/Drive Machine Data

1.5 General bits

1.5 General bits
MD No. 7
5000
5001
5002
Working area
5003
No delay at
limitat.
limit switch
effective with
JOG.
Var. increm. Mode group-specific
5004
with DRF
(SW 6) Type B
Keyswitch group
5005
configurable
Axis/spindle
5006
converter
(as from
SW2)
Do not
5007
TO in
include
diameter
TO wear
Path dimen.
5008
REPOS in
from PLC
jog mode
without
NC Stop
5009
Tool offset
5D tool length
5010
for gear cut.
compensation
tools
5011
@read / Act. value
load display
5012
5013
Circle
Polar
program-
coordinates
ming
programming
5014
Tool radius Blueprint
compensa- program-
tion (TRC) ming
5015
5016 Slave axis
5)
sorting
5017
Transform- Transform.
ation mach. data
machine data change with
change active
without warm transform.
restart permiss.
(SW 6.2, 5.8) (SW 6.2, 5.8)
5018
2nd CP 1st CP
module module
5019 Soft
approach
and retract
5020
2) SW 3 and higher
3) Up to SW 2
4) SW 4 and higher
5) SW 4.4 and higher
6) SW 6 and higher
1–18
Bit No.
6 5 4
Input resolution
Interpolation Polar coordi-
parameters nate angle
dependent on dependent on
G90/G91 G90/G91
Own rapid
single block
override
Type A
ZO fine
ELG pro-
gramming
via input
display
Mixed prog-
ramming
G90/G91 in
block
INC and
TO type 0
REF in jog
like type 20
mode
Diameter function for
G91 pro- G90 progr.
gramming + TO wear
Feed not
related to
contour
Cycles
(Reference
conditioning)
Path dim. Division
from PLC from PLC
Scale
factor
© Siemens AG 1992 All Rights Reserved
3 2 1
Name of radius and chamfer
Name of angle
Internal WAIT
mark synchro-
Auxil. function
PRESEToffset
nization with
output before
not deleted at
block search
Power On traversing
(SW 5.6 and
higher)
NC-Start
2nd
without ref.
point for
handwheel available
all axes
K e y s w i t c h e f f e c t i v e i n
p o s i t i o n 1 - 2 - 3
ZO coarse R
TO
TO wear
parameters
geometry
Angle of rot.
K e y s w i t c h e f f e c t i v e w i t h
Part prog.
Dry run
DRF
manual
feedrate
input
TO basic
No output G53 like
dimension
of M17 @706
active
Command
chan. on mode
group disable
(from SW 5)
Type 5D tool length compensation
Incr. dim.
Zero offset TO wear
TO geometry (hand-
(Type 1-9)
wheel), DRF
Sign change
Do not delete Writing of
handwheel 2
workpc. name machine data
(from
on PLC progr. disabled
selection 2)
SW 6.3)
by @
Tapping
M and S add.
without
extens. for
encoder
spindle at PLC
Extended
contour
definition prog.
External
data input
File
tranfer
Coupled High
Mem. expans.
motion of resolution
to 819 tools
axes rotary axis
3)
Emergency
retraction off
SINUMERIK 840C (IA)
09.01
0
No NC Stop in
dwell block
G045/G14/G24
(SW 5.4 and
higher)
1st
Overstore
Tool length
comp. also in
non-program.
axes
CANCEL key
acts channel-
specific (as
from SW2)
6)
Sign change
handwheel 1
(from
SW 6.3)
G63 without
delay
Thread and
revol. feedrate
G33/G95
3D inter-
polation
Mem. expans.
to 409 tools
3)
6FC5197- AA60