Empire Comfort Systems DVCP36PP30N-1 Installation Instructions And Owner's Manual page 2

BEFORE YOU START
Sample Warnings and Definitions:
DANGER
Indicates a hazardous situation which, if not avoided, will result
in death or serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a hazardous situation which, if not avoided, could
result in minor or moderate injury.
NOTICE:
Addresses practices not related to personal injury.
1. Read the safety information on Pages 75 - 76.
2. If located in the Commonwealth of Massachusetts, please
note the special requirements on page 77.
3. Are you going to install a blower into the fireplace? See
pages 8 - 9.
4. Where are you going to install the fireplace? See page 17.
5. Frame the opening. See page 19.
6. Install the gas lines. See page 16.
7. Install the wiring. See pages 59 and 63.
8. Install the venting. See pages 25 - 32.
9. Install the fireplace. See pages 19 - 24.
10. Connect the venting system. See pages 33 - 34.
11. Install the logs. See page 36 - 54.
12. Light the fireplace and troubleshoot. See pages 60 - 61 and
64 - 67.
13. Show the homeowner how to operate the fireplace.
14. Show the homeowner how to do the basic maintenance.
Page 2
Unpacking the fireplace
NOTICE: The barrier screens supplied with this fireplace may
be damaged if force is applied to their surfaces. Take care not to
push against barrier screens.
1. Cut binding straps and shrink wrap. Shrink wrap should be
cut vertically along a corner post to avoid damage to barrier
screens.
2. Remove and discard corner posts.
3. Remove and discard top plywood sheet.
4. Verify that the fireplace has not been damaged during
shipping.
5. Remove non-combustible board on vent-end of fireplace and
set aside (peninsula only).
6. Remove fireplace from pallet.
7. Remove non-combustible boards from pallet and set aside.
8. Set fireplace in a location near to its final installation location.
NOTICE: It is not necessary to remove the barrier screens from
the glass frames in order to remove the glass frames (see page
69).
Installation Considerations - Fireplace Installation
Guidelines
When planning a fireplace installation, it's necessary to
determine:
• If the desired location of the fireplace is compatible with the
required framing dimensions, clearances to combustibles, venting
requirements, etc.
• If optional accessories are desired.
• Routing of gas supply piping (vent-end entrance).
• Electrical connections - for IP control system or optional light
or blower kit (vent-end connection)
• Electrical supply requirements for IP control system or
optional light or blower kit. (120V, 60Hz, 1Amp) (Vent-end
connection)
The fireplace can be mounted on any of these surfaces:
1. A flat hard combustible or non-combustible surface.
2. A raised platform of combustible or non-combustible material.
3. If allowed by local codes: A rectangular frame that contacts
all four edges on the bottom of the fireplace.
If the fireplace is installed directly on carpeting, tile or other
combustible material other than wood flooring, it should be
installed on a metal or wood panel extending the full width and
depth of the fireplace.
This fireplace is designed to be installed in a zero-clearance
enclosure. This means the combustible material can come in
contact with the top and side standoff spacers, and secured to
combustible framing using the framing brackets provided.
36092-2-0316
CARTON CONTENTS & HARDWARE PACK
CARTON CONTENTS - DVCP36(PP,SP)3 SERIES
1 2
5
4
NAT Unit LP Unit
Items not shown to scale.
QUANTITY
INDEX NO. DESCRIPTION
SUPPLIED
1 Rock Wool
2* Nailing Flange
3 Hardware Pack
4 Shut-Off Valve
5 Flue Restrictor
NS Non-Combustible Board - Long
NS** Non-Combustible Board - Short
NS Installation Instructions
NS - Not Shown in reference graphic.
*Five required for Peninsula models. Four required for See-Thru
models.
**Peninsula models only.
See Parts Lists on pages 70 - 73 for ordering replacement parts.
Do not order batteries, bolts, screws, washers or nuts. They are
standard hardware items and can be purchased at any local
hardware store.
36092-2-0316
CARTON CONTENTS - DVCP36(PP,SP)7 SERIES
3
1 2
5
4
NAT Unit LP Unit
Items not shown to scale.
INDEX
DESCRIPTION
NUMBER
1 1 Rock Wool
5 2* Nailing Flange
1 3 Hardware Pack
1 4 Shut-Off Valve
1 5 Flue Restrictor
2 6 Battery
1 7 AC Adapter
1 NS Non-Combustible Board - Long
NS** Non-Combustible Board - Short
NS Installation Instructions
NS - Not Shown in reference graphic.
*Five required for Peninsula models. Four required for See-Thru
models.
**Peninsula models only.
See Parts Lists on pages 70 - 73 for ordering replacement parts.
Do not order batteries, bolts, screws, washers or nuts. They are
standard hardware items and can be purchased at any local
hardware store.
3
6
7
QUANTITY
SUPPLIED
1
5
1
1
1
4
1
2
1
1
Page 3