Advertisement
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
Read all instructions before using this Heater.
WARNING
• ALWAYS PLUG HEATERS DIRECTLY INTO A WALL OUTLET/RECEPTACLE. NEVER USE WITH AN EXTENSION CORD. DO
NOT PLUG HEATER INTO ANY OTHER CORD CONNECTED DEVICE, SUCH AS A POWER STRIP, SURGE PROTECTOR,
MULTIPLE OUTLET ADAPTER, CORD REEL OR OUTLET-TYPE AIR FRESHENER. THE USE OF SUCH DEVICES MAY CREATE
A FIRE HAZARD. PLUG UNIT DIRECTLY INTO A 120V WALL OUTLET ONLY.
• FAULTY WALL OUTLET CONNECTIONS MAY CAUSE THE WALL OUTLET TO OVERHEAT. BE SURE THAT HEATER PLUG
FITS TIGHTLY INTO OUTLET BEFORE EACH USE. DURING USE, CHECK TO MAKE CERTAIN THE HEATER PLUG IS
NOT OVERHEATING. IF NECESSARY HAVE A QUALIFIED ELECTRICIAN CHECK AND/OR REPLACE THE WALL OUTLET. DO
NOT USE THIS HEATER WITH ANY SOLID STATE SPEED CONTROL DEVICES.
• Make certain that the power source conforms to the electrical requirements of the Heater.
• Extreme caution is necessary when any Heater is used by or near children or invalids. The Heater should not be left
operating unattended. Never leave children unattended when the heater is on or plugged in.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended
to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician. Do not attempt to defeat this safety feature.
• DO NOT use the Heater in areas where gasoline, paint, or flammable liquids are used or stored. DO NOT use Heater in locations
where flammable or explosive chemicals are stored, or in wet atmospheres.
• Do not operate any Heater with a damaged cord or plug or after the Heater malfunctions, or has been dropped or damaged in any
manner. To disconnect Heater, turn the Heater OFF then remove the plug from the outlet.
• Always unplug Heater when not in use. Unplug power cord before servicing or moving the Heater.
• Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock, fire, or
damage the Heater. Do not block or tamper with the Heater in any manner while it is in operation.
• Do not block air intakes or exhaust in any manner. Do not place on soft surfaces, like a bed, where openings
may become blocked. Do not depend on the on/off switch as the sole means of disconnecting power when servicing or moving the
heater. Always unplug the power cord.
CAUTION
• Always place the Heater on a stable, flat, level surface when operating, to avoid the chance of the Heater overturning. Locate the Power Cord so
the Heater or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with throw rugs, runners, or
similar coverings as this may cause cord to overheat. Arrange Power Cord away from room traffic and where it will not be tripped over.
• This Heater is HOT when in use. To avoid burns, do not let bare skin touch hot surfaces. Always use handle when moving this Heater. Keep
combustible materials, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9 m) from the front of the Heater and keep
them at least 1 foot (0.3 m) from the sides and rear.
• This Heater is not intended for use in wet or damp locations. This Heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate a Heater where it may fall into a bathtub or other water container.
• DO NOT use Heater outdoors.
• This Heater is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please refer
to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for
Agricultural Buildings. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
• This Heater is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes
or standards relating to electrical requirements for Hazardous locations. THIS HEATER DOES NOT MEET THE REQUIREMENTS OF NEC
ARTICLE 500 (2008).
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the
equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the
dealer or an experienced radio/TV technician for help. The user is cautioned that changes and modifications made to the equipment without the
approval of manufacturer could void the user's authority to operate this equipment.
Please contact Customer Service at 800-233-0268 Monday through Friday from 8am to 5pm EST for assistance.
SAVE THESE INSTRUCTIONS
Rev. F 5/13
WARNING
2
FUNCIONAMIENTO
(Figuras 1 y 2)
1. Cuidadosamente retire su Calentador de la caja y la bolsa.
2. Coloque el Calentador sobre una superficie firme y
tacos de plástico o hule, tales como las patas de esta unidad,
pueden pegarse a la superficie de los muebles y/o a los pisos de
madera. La unidad podría dejar un residuo capaz de oscurecer,
manchar o dejar marcas permanentes en el acabado de ciertas
superficies de muebles, incluyendo superficies de madera y/o
pisos de madera.
3. Asegúrese que el Calentador esté en la posición de "APAGADO"
(0) antes de conectar el Calentador al tomacorriente.
4. Conecte el cable a un tomacorriente de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos dentro de
los tomacorrientes, podrían deslizarse parcial o
completamente fuera del tomacorriente con el menor
movimiento del cable adosado. Los tomacorrientes en
este estado podrían sobrecalentarse y representar un
peligro de incendio grave; si queda cubierto por una
cortina o tela, el peligro de incendio es todavía mayor.
5. Cuando el Calentador sea encendido por primera vez, la Luz
de Encendido se encenderá indicando que hay electricidad
en la unidad. La Luz de Encendido permanecerá encendida
hasta que el Calentador sea desconectado del tomacorriente
eléctrico.
6. Coloque la Perilla del Termostato en la Posición Máxima ( ).
7. Mueva la Perilla de Encendido hasta la posición de calor
deseada. El Calor Alto (1500 vatios) está representado por el
(2) y el Calor Bajo por el (1).
8. Sólo para hacer funcionar el ventilador, gire la perilla de
encendido a (
)
9. Para ajustar el ángulo del flujo de aire del Calentador, haga girar
el cuerpo del Calentador hacia delante o hacia atrás hasta la
posición deseada. Figura 2
10.La Luz de Encendido permanecerá encendida durante el
funcionamiento.
11.Para desconectar el Calentador, gire la Perilla de Encendido
hacia la posición de "APAGADO" (0), luego retire el enchufe
del tomacorriente.
ADVERTENCIA:
EL TEJIDO DE MALLA PLASTICO DE LA
Perilla de
Encendido
Luz de
Figura 1
Encendido
675900ES
Rev. F 5/13
MODELO 675900
PARRILLA ESTÁ CALIENTE CUANDO EL CALENTADOR ESTÁ
EN FUNCIONAMIENTO.
OPERACIÓN DEL TERMOSTATO
planaLos
1. Fije la perilla del termostato al darle vuelta en el sentido de
las agujas del reloj hasta el símbolo de (+) y permita que el
Calentador caliente la habitación.
2. Cuando se alcance el nivel de comodidad deseado, disminuya
el termostato hasta que se apague la unidad. Esto se realiza al
darle vuelta a la perilla del Termostato en el sentido contrario a
las agujas del reloj hasta el símbolo de (-).
3. El Calentador mantendrá automáticamente el nivel de comodidad
deseado al realizar el ciclo de encendido (ON) y apagado
(OFF). Para una calefacción continua, fije el termostato hasta
el símbolo (+).
NOTA: Se recomienda ajustar el termostato con cada uso. Los
cambios diarios en la temperatura externa y de la habitación
afectarán la posición en la cual su termostato se encenderá o
apagará.
Vista Lateral del Calentador
Figura 2
Perilla del
Termostato
7
Parrillas
de
Entrada
675900ES
Advertisement
