Camera Adjust Mode, Eeprom Address Sequence And Data Of Page 0 - Samsung SCL700 Service Manual

"CAMERA ADJUST MODE, EEPROM ADDRESS SEQUENCE & DATA OF PAGE 0"
CAMERA AUTO ADJUST MODE
0DF A0 - - -
0CD FF - - -
0CE FF - - -
0CF FF - - -
0D0 FF - - -
0D6 FF - - -
0DB FF - - -
0DE FF - - -
NO-OSD-DISPLAY
ADDR MODEL/DATA
NTSC PAL
HI8 NOR HI8 NOR
000 00 01 02 03
001 C6 46 C6 46
46 46
002 67 - - -
003 A5 - - -
004 70 - - -
005 08 - - -
006 44 - - -
007 44 - - -
008 03 - - -
009 B0 - - -
00A 75 - - -
00B 3D - - -
00C 85 - - -
00D 50 - - -
00E 02 - - -
00F 1C - - -
010 30 - - -
011 00 00 01 01
012 F7 F6 23 23
013 01 00 01 00
014 80 FF 78 FA
015 D2 D2 D2 2D
016 01 - - -
017 74 - - -
018 A0 - D0 D0
019 05 - 05 05
01A 70 - - -
01B 0B 0B 0B 0B
01C 80 - - -
01D B0 B0 B0 88
01E 98 98 98 98
01F 98 98 98 98
020 60 - - -
021 08 05 - 05
022 00 - - -
023 E5 - - -
024 80 - - -
025 38 - - -
026 A0 - - -
Samsung Electronics
;EEPROM -TABLE -INITIAL (CAMERA ONLY:'99'+CONFIRM =EXCEPT(#061~#067,#680~#7FF),"
;HALL AUTO ADJUST
;IRIS AUTO ADJUST
;W/B AUTO ADJUST
;LENS AUTO ADJUST(WARNNING! DON°ØT'S USE WITHOUT AN INFINITE COLLIMATOR)
;ZOOM VR CENTER ADJT
;AGC AUTO ADJUST(NORMALLY NOT USED)
;3M LENS AUTO ADJUST AT SERVICE FIELD(DISTANCE :3M +/- 1Cm)
D7 D6 D5
; 00=NTSC HI8, 01=NTSC NORMAL, 02=PAL HI8, 03= PAL NORMAL
; DIS MODEL="C6" , NON-DIS MODEL="46"
NON-DIS MODEL="46", DIS MODEL="C6" ,
; @IRIS CONTROL-LOW
; @IRIS CONTROL-HIGH
; @P.CLK PWM-HIGH (ADCLK ;PAL HI8:14.250MHz, PAL-normal: 9.494800MHz NTSC:9.534964MHz)
; UPD16879 INIT 4th
; UPD16879 INIT 6th focus
; UPD16879 INIT 7th zoom
; CDS F-REG(f1,f0) CAM : BIT0:f0,BIT1:f1
; CDS F-REG(f9,f2) CAM ;PGA GAIN -HIGH(0.00dB~ 30.0dB)
; CDS G-REG CAM ;DAC1 INPUT(HALL REFERENCE CONTROL;0V~3.0V)
; CDS H-REG CAM ;DAC2 INPUT(HALL GAIN CONTROL;0V~3.0V)
; CDS E-R(e1,e0),J-R(j0),M-R;D0:e0,D1:e1,D2:j0(CAM),D4:e0,D5:e1,D6:j0(VCR),D7:cds-rev='1'
; CDS F-REG(f9,f2) VCR COLOR ;PGA GAIN HI8 ME
; CDS IC A REG AT VCR MODE
; CDS TE-R (D0:T-R D9 set='0'=offset=E-R,'1'=offset=#010(d0~d5: add111: d4~d9),D1:T-R
; CDS OFFSET (#00F: D0='1' OFFSET VALUE)
; VNTPAL2_H ccd vertical effective line
; VNTPAL2_L ccd vertical effective line
; HNTPAL2_H ccd horizental effective pixel
; HNTPAL2_L ccd horizental effective pixel
; PHG hg phase : DZOOM - EEPROM #296 CONTROL
; Mpoint_H mirror point h : MIRROR- EEPROM #336
; Mpoint_L mirror point h : MIRROR- EEPROM #337
; AE TARGET-LOW BYTE (NON-DIS)
; AE TARGET-HIGH BYTE (NON-DIS)
; DIS AE TARGTE LOW
; DIS AE TARGET HIGH
; FLEX ZONE AE TARGET PERCENT( 80H= AUTO TARGET)
; SPOT LIGHT AE TARGET PERCENT( DIS: B0 , NON-DIS: 88)
; BLC ON AE TARGET PERCENT(DIS: 80 , NON-DIS: 77)
; SAND SNOW AE TARGET PERCENT( DIS: 90 , NON-DIS: 88)
; NEGA BLC AE TARGET PERCENT( 80H= AUTO TARGET)
; AGC =#022 VALUE: #22F- H ENHANCER MIN
; AGC =#022 VALUE :#237- V ENHANCER MIN
; AGC MAX % (E5=90%) FOR H,V ENHANCER MIN (#021,022)
; IRIS CONTROL GAIN '80'=CENTER
; SHUTTER START POINT OF IRIS CONTROL PERCENT(FF=100% IRIS OPEN)
; AGC AETRGET PERCENT( =AETARGET*(#026/100hex)
CONTENT
DISTANCE
CONTENT
D4 D3 D2
CCD WHITE DEFECT DETECT AGC
d3,D2D3=C0C1(CAM), D4D5=C0C1(VTR)
Alignment and Adjustment
'AA'=ALL DATA INITIAL)
D1 D0
4-5