Subscribe to Our Youtube Channel
Related Manuals for Majestic concert marimba
Summary of Contents for Majestic concert marimba
- Page 1 Mallet Instrument Assembly Instructions Concert Marimba — 4 Octave Model Concert Xylophone — 4 & 3-1/2 Octave Model Concert Vibraphone — 3 Octave Model 產品組立說明書： 室內型立奏低音木琴 — 4 個八度音型號 室內型立奏高音木琴 — 4 & 3-1/2 個八度音型號 室內型立奏顫音鋁琴 — 3 個八度音型號...
- Page 2 Materials 零件 Check contents carefully. Each model should include following: 每一組琴應該要包括下列組件，請仔細檢查內容： Item Parts Description 零件敘述 Qty 數量 Leg Assembly with 4" Casters 木琴側架含 4" 腳輪 2 Units Cross Bar 1 PC 方型連結桿 Curved Brace 2 PC 圓弧形支撐架 Pedal Assembly (Vibraphone Only) 踏板組件（顫音鋁琴）...
- Page 3 Frame Set Up & Resonator Attachment 琴架、琴框、共鳴管組裝 Connect curved braces to cross bar with hand knob. Do not tighten. 將圓弧形支撐架與方形連結桿以旋鈕結合，但請勿鎖緊。 Marimba & Xylophone Vibraphone 立奏低音 / 高音木琴 立奏顫音鋁琴 Identify low end leg assembly. With leg assemblies lying flat with the height adjustment crank handle on the floor and the crossbar receivers facing up, the low end leg will have the wheel with brake on the left.
- Page 4 Set low (wide) end leg assembly upright; then secure crossbar and brace ends to high (narrow) end leg assemblies as in Step 2. 立起低音側琴架，再將將高音側琴架與連結桿、支撐架同步驟 2 固定並鎖緊。 Lock wheels on leg assemblies by engaging brake mechanism on wheels on player side. Set low end leg assembly with attached crossbar upright, then secure crossbar and curved brace to high end leg assembly as in Step 2.
- Page 5 Wing screws also need to be loosened for height adjustment of instrument. Pedal height must be reset after eight adjustment as been made. 進行顫音琴高度調整時，此蝶螺絲亦需鬆開，調整完畢后需重新設定踏 板高度。 − Besides the preset pedal weight, user can switch to the other connecting position for heavier pedal response. 踏板反應力度除原廠預設外，使用者需可依其所好，將拉桿連接是前一...
- Page 6 (Vibraphone only) Align rotors of two resonator banks; then loop motor belt around fan pulley at naturals side, and under security plate. 先將共鳴管活葉調整於相同開闔位置，再將馬達皮帶繞於全音共鳴管活頁皮 帶輪上，並置於固定板下方。 Hold the rotor shaft at Naturals side, then turn the shaft of Accidentals side, until motor belt fit in the pulley at accidentals side. 用左手扶住已經裝好馬達皮帶的全音共鳴管活頁轉動軸，右手旋轉半音活頁...
- Page 7 Tone Bar Mounting 音板裝置 Height Adjustment — Operate hand crank on side of leg assemblies to raise or lower as needed. Adjust one end at a time, using imprinted scale as a guide. 腳架高度調整 轉動側架上的把手，依刻度記號調整至適當高度。 Adjustment range should not exceed 4" per side without adjusting the other side.
- Page 8 Mallet Instrument Ver.201205 www.majestic-percussion.com...
Need help?
Do you have a question about the concert marimba and is the answer not in the manual?
Questions and answers