Table of Contents
Advertisement
Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any attachment and before cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
CAUTION: Use caution when handling the blade
assemblies as the blades are very sharp.
1
Separate/remove all parts from each other.
2
Clean the motor base with a damp cloth and wipe dry.
3
Place the lids, pitcher, bowl, Nutri Ninja
™
cups and
blade assemblies in the dishwasher. Place the lids and
attachments on the top rack.
OR
4
Carefully hand wash the lids, pitcher, bowl, Nutri Ninja
cups and blade assemblies in warm, soapy water with a
soft cloth.
15
086 728 8149 (Calls charged at VAS rates. Free minutes do not apply.)
HOW TO STORE
1
Store the Nutri Ninja | Ninja Blender System with Auto-iQ
Technology upright with the pitcher on the motor base,
stacked blade inside the pitcher and lid on the pitcher. Do
not place anything on top. Store the Food Processor Bowl
with the chopping blade inside and the lid on top. Store
the Nutri Ninja cup and the rest of the attachments along
side the appliance or in a cabinet where they will not be
damaged and won't cause a hazard.
RESETTING THE MOTOR THERMOSTAT
The Nutri Ninja | Ninja Blender System with Auto-iQ
Technology features a safety system which prevents
damage to the unit's motor and drive system should you
inadvertently overload your
appliance. If the appliance
is being overloaded, the motor will stop.
Allow
the appliance to cool for approximately 15
minutes. To reset the appliance, follow the resetting
procedure below:
1
Unplug the appliance from the electrical outlet.
2
Remove and empty the container and ensure that no
food is jamming the blades or attachments.
3
Allow the appliance to cool for approximately 15
minutes.
4
Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5
Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.
Troubleshooting Guide
PROBLEMS
™
Motor Doesn't Start or
Attachment Doesn't Rotate.
Food is Unevenly Chopped.
Food is Chopped Too Fine or is
Too Watery.
Food Collects On Lid or On the
Sides of the Container.
You Cannot Achieve Snow
From Solid Ice.
Motor Base Won't Stick to
Counter or Table Top.
You get an "Err" Message.
You have a blinking red light.
POSSIBLE REASONS & SOLUTIONS
Make sure the container is securely locked into the motor base.
Make sure the lid is securely on container in the correct position (align arrows).
The appliance is turned "Off". Press the power button ( ) to turn "On".
Check that the plug is securely inserted into the electrical outlet.
Check the fuse or circuit breaker.
The unit has overloaded. The appliance will stop and the power light will flash.
Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before using again.
Check to make sure the unit is not overloaded.
Either you are chopping too much food at one time, or the pieces are not of even
size and processing smaller amounts per batch.
The food has been over processed. Use Auto-iQ
Pulse button for controlled
™
processing.
The mixture is too thick. Add more liquid.
Do not use ice that has been sitting out or has started to melt. Use ice straight
from the freezer.
Start with a few pulses and then go to a continuous blending cycle.
Make sure surface and suction feet are wiped clean. Suction feet will only stick to
smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood,
tile and non-polished finishes.
DO NOT attempt to use appliance when the motor base is stuck to a surface that
is not secure, (cutting board, platter, plates, etc.).
Your Ninja
is able to detect which jar is on the base. You may be trying to use a
™
program that is not designed for the jar you have installed. The programs will light
up indicating which programs are available for each jar.
The unit is not installed properly. For your safety the unit will only be able to be
turned on when it is properly assembled. Please refer to the assembly pages of
this inspiration guide for assistance.
www.ninjablenders.co.za
16
Advertisement
Table of Contents
