Advertisement
Before First Use
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN USING THE
APPLIANCE:
IMPORTANT: Make sure that the motor base
is plugged in for use.
IMPORTANT: Never add ingredients into the
container before placing the attachment in
first.
IMPORTANT: Attachments are not
interchangeable.
IMPORTANT: DO NOT attempt to operate the
appliance without the lid on.
IMPORTANT: Never run the appliance empty.
IMPORTANT: Appliance accessories are not
intended to be used in the microwave as it
may result in damage to the accessories.
7
1-877-646-5288
WARNING: Stacked
Blade Assembly is
sharp and not locked in
place. If using the pour
spout, ensure the lid
is fully locked onto the
blender pitcher. Failure
to do so will result in a
risk of laceration.
WARNING: Stacked
Blade Assembly is
sharp and not locked
in place. If pouring
with the lid removed,
carefully remove
the Stacked Blade
Assembly first holding
it by the shaft. Failure
to do so will result in a risk of
laceration.
CAUTION: Do not immerse the motor base
into water or any other liquid.
1
Remove all packaging material and labels from the appliance.
Separate/remove all parts from each other.
2
Wash the lids, pitcher, Nutri Ninja cups and blade
assemblies in warm, soapy water. When washing the
blade assemblies, use a dish-washing utensil with a
handle to avoid direct hand contact with blades.
WARNING: Handle the Stacked Blade Assembly
and Nutri Ninja Blade Assembly with care when
washing, as the blades are sharp.
3
Handle blade assemblies with care to avoid contact
with sharp edges. Rinse and air dry thoroughly.
4
The pitcher, Nutri Ninja cups, lids, Stacked Blade
Assembly and Nutri Ninja Blade Assembly are all
dishwasher safe. It is recommended that the lids and
blade assemblies be placed on the top rack. Ensure
the blade assembly is removed from the cup or pitcher
before placing in the dishwasher.
5
Wipe the motor base clean with a damp cloth.
Assembly & Use of the Pitcher
WARNING: Handle the Stacked Blade Assembly with care, as the blades are sharp.
WARNING: Remove utensils prior to processing. Failure to remove may cause the pitcher to be damaged or
to shatter, which may cause personal injury.
WARNING: Never leave the appliance unattended while in use.
CAUTION: Do not blend hot liquids, doing so may cause excessive pressure buildup, resulting in risk of the
user being burned.
IMPORTANT: Make sure that the motor base is plugged in for use.
ASSEMBLY
Fig. 1
Fig. 2
It's best to add the liquid ingredients first and then the dry ingredients.
1
Review warning and caution statements above before
proceeding to number 2.
2
Place the motor base on a clean, dry, level surface such
as a counter or table top.
3
Align and lower the pitcher onto the motor
base. (Fig. 1) Handle should be aligned slightly to the
right of the "LOCK" symbol on the motor base.
4
Rotate the blender pitcher clockwise until it clicks in
place. As the pitcher rotates, it will lower and the safety
tabs on the bottom of the pitcher will slide under the
safety tabs on the top of the motor base. (Fig. 2)
5
The pitcher can be placed on the motor base two ways;
the handle can be on the front right corner or the front
left corner. (Fig. 3a, Fig. 3b)
6
Holding the Stacked Blade Assembly by the top of the
shaft, place it onto the drive gear inside the pitcher.
Ensure that the Stacked Blade Assembly is seated
properly and is standing upright. (Fig. 4)
NOTE: The Stacked Blade Assembly will fit loosely on
the drive gear.
Fig. 3a
OR
Fig. 3b
Fig. 4
Fig. 5
7
Add the ingredients to the pitcher, making sure that
they do not exceed the highest measured marking line
on the side of the pitcher.
NOTE: If you need to add additional ingredients while
the appliance is processing, open the pour spout cap
and pour the ingredients in through the opening.
NOTE: When blending any kind of liquids, such as
mixtures of any drinks or smoothies, do not exceed the
"Max liquid" mark (64 oz.) on the pitcher.
8
Plug the power cord into the electrical outlet and press
the power button ( ).
IMPORTANT: As a safety feature, the power
button ( ) will flash and the motor will not work
if the pitcher and lid are not installed correctly.
When the pitcher and lid are installed properly,
the power button ( ) will be solid, indicating that
the appliance is ready for use.
9
Holding the lid by the handle in the upright
position, place it on top of the pitcher aligning the
arrow ( ) located on the lid with the arrow ( ) located
on the pitcher's handle. (Fig. 5)
ninjakitchen.com
8
Advertisement
