Summary of Contents for Dvico FusionHDTV 5 GOLD
- Page 1 FusionHDTV 1. Before Getting Started 2. Software Installation 3. Hardware Installation 4. Using FusionHDTV...
- Page 2 Agreement or the use of or inability to use the Products, even if DViCO has been advised of the possibility of such damages. Because some states/jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation applies only to the extent permitted by applicable law.
- Page 3 DViCO and Licensee relating to the subject matter of this Agreement. This Agreement may not be modified except in a writing duly signed by an authorized representative of DViCO and Licensee. If any provision of this Agreement is held to be unenforceable for any reason, such provision...
-
Page 4: Table Of Contents
Before Getting Started..................5 FusionHDTV Specification ....................5 FusionHDTV System Requirements ..................7 Package contents.......................8 Software Installation ....................9 Installing FusionHDTV Applications ..................9 Driver installation under Windows ME................17 Driver installation under Windows 2000 Professional ............20 Driver installation under Windows XP ................23 Hardware Installation ..................26 About the Board ....................... -
Page 5: Before Getting Started
FusionHDTV Specification A Highly cost effective ATSC/ NTSC TV reception card You can enjoy HDTV at quite a low price due to Dvico’s innovative HDTV software decoding engine and enhanced Reception rate with Latest 5th generation chipset. Unrivaled crystal-clear picture quality FusionHDTV provides up to 5 times higher resolution when compared to analog TV, and provides crisp and crystal-clear picture quality to a PC screen. - Page 6 - OSD for virtual channel and broadcasting station name is shown whenever channel is changed. Supports sub-channel Sub channel is listed up in sub channel play list and can be selected with channel up/down button or mouse selection in sub channel play list. Second language Supports the second language in digital broadcasting Supports screen saver off.
-
Page 7: Fusionhdtv System Requirements
FusionHDTV System Requirements System requirements for FusionHDTV are as follows <Input/Output> [ FusionHDTV 5 GOLD ] antenna One inside stereo connection jack to sound card for analog TV S-Video IN, Composite IN External Sound card Connection cable [ FusionHDTV 5 Lite ]... -
Page 8: Package Contents
Package contents The FusionHDTV package contains the following items: [ FusionHDTV 5 GOLD,SILVER ] ① FusionHDTV card ② Setup CD ③ Manual ④ Internal cable to sound card for External output Audio ⑤ External connection cable [ FusionHDTV 5 Lite ] ①... -
Page 9: Software Installation
Please check the site (Http://www.FusionHDTV.co.kr/Eng), before you install the software included in the CD. Installing FusionHDTV Applications Insert FusionHDTV Installation CD into the CD-ROM drive. The setup window will automatically pop up. if you downloaded the recent version on DVICO’s website, please run install.exe or setup.exe. 2.1.1 Uninstall Drivers 1) When you select Uninstall Driver in the menu on the FusionHDTV INSTALLER program, Select your FusionHDTV board type. - Page 10 2.1.2 Installing FusionHDTV Software Important: Installation on Windows 2000 Professional or Windows XP Before you install FusionHDTV software, be sure that you logged on as an account with Administrator privileges. Select “Install FusionHDTV”. At the FusionHDTV Installation dialog opens, click on the “Next>” button. 3) The user Information window will show up.
- Page 11 4) The “Choose Destination Location” window will appear. Click on “Next” if you want to install the FusionHDTV in the default directory. Otherwise, you can choose a different directory by clicking on “Browse”. 5) Press “Next” on the Destination Folder selection window. 6) The “Setup status”...
- Page 12 7) Choose your country, then click “OK”. 8) PC specification selection windows will appear. Please select the appropriate system. You can change the mode after installation with configuration menu of the application program. You do not need to reinstall the program with different options. All specifications and information are subject to changes without further notices...
- Page 13 9) Select your FusionHDTV card, and Press ‘Next’ to install latest drivers. 10) You will see the progress window. All specifications and information are subject to changes without further notices...
- Page 14 14) When you reboot, the system will ask for the 5~6 drivers. Please click “Yes” when the digital signature window appears. <Notes> In certain cases, Windows will ask for the .sys files. You can locate the sys files in the C:\Program Files\DVico\FusionHDTV\driver folder. All specifications and information are subject to changes without further notices...
- Page 15 2.1.3 Installing Microsoft DirectX 9 Important! Installing on Windows 2000 Professional or Windows XP Before you install FusionHDTV software, be sure that you logged on as an account with Administrator privileges. You can check the version of DirectX by typing “dxdiag” on the command line which appears with menu selection “start->run”...
- Page 16 If there is a DirectX already installed in the system, a different window will show up instead of the one above. 4) Click on “ Finish” to restart system and complete installation of the DirectX . All specifications and information are subject to changes without further notices...
-
Page 17: Driver Installation Under Windows Me
Component (ATSC-A)” driver will be installed automatically. 4) After the Files Needed Window appears, look for the ‘zl88Tcap.sys’ file by clicking the browse button. Select driver directory under installation directory. C:\Program Files\Dvico\FusionHDTV\driver) All specifications and information are subject to changes without further notices... - Page 18 5) If a version conflict message appears during installing, preserve existing file by pressing ‘ Keep’ . 6) The Add New Hardware Wizard will pop up automatically and “ F usionHDTV 88x, WDM ATSC TvTuner (LG062F)” driver installation will be done automatically. 7) The Add New Hardware Wizard will pop up automatically and “...
- Page 19 [ FusionHDTV 5 Lite ] [ FusionHDTV 5 GOLD, 5 GOLD PLUS, FusionHDTV 5 Silver , 5 Silver PLUS ] ** In certain cases, Windows will ask for the .sys files. You can locate the sys files in the C:\Program Files\DVICO\FusionHDTV\driver or C:\Windows\System32\Drivers folder.
-
Page 20: Driver Installation Under Windows 2000 Professional
Driver installation under Windows 2000 Professional 2.3.1 Before Installa tion Make sure that you install the software in the following order. 1) Install the Application software(refer to 2.1 Installing FusionHDTV Applications) 2) Install hardware(board) (refer to 3.3 Board Installation) 3) Install the Windows 2000 Drivers (refer to 2.3.2 Installing Windows 2000 driver) 4) Check Windows 2000 device manager (refer to 2.3.3 Checking Windows Driver) 2.3.2 Installing Windows 2000 driver... - Page 21 FusionHDTV 88x, BDA ATSC Tuner/Demod (LG062F),FusionHDTV 88x, WDM ATSC TvTuner (LG062F),FusionHDTV 88x, WDM Crossbar drivers. If a driver file look for, click the browse button. Select the driver directory under the installation directory (ex : C:\Program Files\Dvico\FusionHDTV\driver) or Driver folder of installation CD. 2.3.3 Checking the Windows 2000 driver Right click the “My Computer”...
- Page 22 [ FusionHDTV 5 Lite ] [ FusionHDTV 5 GOLD, 5 GOLD PLUS, FusionHDTV 5 Silver , 5 Silver PLUS ] All specifications and information are subject to changes without further notices...
-
Page 23: Driver Installation Under Windows Xp
Driver installation under Windows XP 2.4.1 Before Installation Make sure that you install the software in the following order: 1) Install the Application software (with reference to 2.1 Installing FusionHDTV Applications) 2) Install Hardware (refer to 3.3 Board Installation ) 3) Install the Windows XP drivers (with reference to 2.4.2 Installing Windows XP driver) 4) Check Windows XP Device Manager (with reference to 2.4.3 Checking Windows XP Driver ) 2.4.2... - Page 24 3) After files are copied, Click “Finish” if the FusionHDTV 88x, WDM Video Capture (NTSC) driver is properly installed. Using this way, you may install “FusionHDTV 881, WDM Audio Capture”, “FusionHDTV 88x, BDA Receiver Component (ATSC-A)”, “FusionHDTV 88x, BDA ATSC Tuner/Demod (LG062F) ,FusionHDTV 88x, WDM ATSC TvTuner (LG062F)”, “FusionHDTV 88x, WDM Crossbar”...
- Page 25 [ FusionHDTV 5 Lite ] [ FusionHDTV 5 GOLD, 5 GOLD PLUS, FusionHDTV 5 Silver , 5 Silver PLUS ] All specifications and information are subject to changes without further notices...
-
Page 26: Hardware Installation
Analog Audio Output Port Antenna Antenna: Connects to the terrestrial signal or cable Analog Audio Output Port : For the audio of analog sources. [ FusionHDTV 5 GOLD ,SILVER ] Analog Audio Output Port Antenna VIDEO-IN Antenna: Connects to the terrestrial signal or cable VIDEO-IN: For external video sources. -
Page 27: Before Installation
Before Installation Warning: Before installing, first touch the grounded part of the PC to protect the components on the board from static electricity. Before installing the board, the system’s power should be turned off. Installing the Board when the system’s power is “ON,” will damage the system or the Board. Please remove the power cord from the PC. -
Page 28: Remote Installation
FusionRemote icon at the low right bottom of screen. FusionRemote icon in the tray, please start the program by Start->Program->DViCO- >FusionRemote. Please select the port that IR receiver module is attached and press the any button on the remote transceiver. A Dialog box with the remote transceiver buttons will appear. -
Page 29: Using Fusionhdtv
Starting and Quitting Click Start, point to Program->DVICO->FusionHDTV, or double click on the FusionHDTV icon in the program folder to execute FusionHDTV. When you first execute the program, it will ask for a channel scan. Please say “Yes” for the channel scan. - Page 30 Configuration: Refer to 4.3 : Configuration Show Controller: Show/Hide FusionHDTV’s controller. Recording Scheduler : Used to Reservation Record. Input Source: Change input source. Favorites Channel : Add your favorite programs into favorite list before watching them. Add to Favorite Channel. Display Size: Resize display.
- Page 31 3) Maximize button 4) Configuration button 5) Help button 6) Reserve REC button: is used to Reservation record. 7) LiveTV button: Changes to live TV mode. 8) Input button: is used to select input signal. 9) Time/Signal strength: shows signal strength, if you check Show as hh:mm:ss option on the configuration-display, Total elapsed time played.
-
Page 32: Configuration
Configuration Configuration: ( ), you can Configure many parameters. 4.3.1 Video Video settings tab. Input Source : Selects between multiple external video sources. You can select antenna input between Tuner (OTA) or Cable. FusionHDTV5 Lite doesn’t support the S- video and Composite input. Cropping : flickering lines near the top or bottom of the picture can be removed with cropping function Video tap is possible with adjust Brightness/contrast/Hue/Saturation/Sharpness. - Page 33 4.3.2 Display Display settings tab. Repeat playback: It will play the file endlessly if checked. Show as hh:mm:ss: Shows time from 00:00:00. CUT mode file playback : when you move to the position with scroll bar on the controller of the FusionHDTV, it automatically pause when this option turned on.
- Page 34 For Non DxVA compatible graphics cards. Usually the ones from Matrox. Normal - Intel Pentium 4 : CPU 1.6GHz, AGP 4X - AMD Athlon XP : CPU 1600+, AGP 4X High - Intel Pentium 4 : CPU 2.4GHz, FSB 533, AGP 4X - AMD Athlon XP : CPU 2400+, AGP 4X Highest - Intel Pentium 4 : CPU 2.4GHz, FSB 800, AGP 8X...
- Page 35 4.3.3 Record This section indicates Record settings. Capture Native Record : You can record T p stream to mpeg format with maintaining Video, Resolution, Audio information. (only with the sub-channels). Recording Folder: Sets the folder of files being recorded. Limitless Recording: If the record drive is formatted with NTSF, you are able to record a file continuously on a hard drive.
- Page 36 4.3.4 Channel This section indicates Channel settings: terrestrial digital analog channels and cable digital /analog channels. TV : Select Cable or Air depending on your antenna connection. Type : Scan wanted type. You can scan both. Manual Tune : Check/uncheck wanted/unwanted channels. You can change the station name by clicking on names.
- Page 37 4.3.5 Add To Favorite Channel List Add your favorite programs into favorite list before watching them. Hit the STAR( ) button above the Channel number. Click Insert button and add programs from Channel list to Favorite list. Click Delete button and delete the programs from Favorite list Click Insert All button and add all of the programs from Channel list to Favorite list Click Delete All button and delete all of the programs from Favorite list Click OK and set up current favorite list.
- Page 38 4.3.6 Audio This section indicates Audio settings. TV Multi-Sound : is used to select the analog mono ,stereo or Multi-Language. TV Audio Input: When you watch outer input(S -VHS,Video), you can set the input of sound card. FusionHDTV 5 Lite need to connect the internal audio cable(4 pin) when the analog TV is played. Analog Audio Attenuation : Analog audio level can be adjustable.
- Page 39 4.3.7 Analog This section indicates Analog settings. Size(NTSC) : Initialize to VCD : 352*240 , S-VCD : 480*480 ,MPEG-1 : 320*240 MPEG2 : 640*480 ,DVD : 720*480 Size(PAL) : Initialize to VCD : 352*288 , S-VCD : 480*576 ,MPEG-1 : 320*288 MPEG2 : 720*576 ,DVD : 720*576 Quality : When MPEG-1,MPEG-2,DVD ,You can select Lowest,Low,Normal,High,Highest.
- Page 40 4.3.8 OSD This section indicates OSD settings. Show OSD: Is used to show channel and v olume; on screen display. Show Signal Strength : Is used to show Signal Check.( % or db) Use BIG OSD : Is used to FusionRemote. Advanced OSD : If you click (MENU button) on remote controller, you can use advancedOSD Setting.
- Page 41 4.3.9 Time Shifting This section indicates Time-Shifting settings. Time Shift Folder : temporary recording folder. We recommend to 7200RPM or above hard disk. The FF/REW Function is available Windows XP Service Pack 2 or above. Instant replay seconds will be applied when you press the (Instant replay button), and it’s adjustable from 2 to 60 seconds.
-
Page 42: Record
Record 4.4.1 Manual Record When you want record On-Air right away, click (Record button) on FusionHDTV‘s controller. If you want to terminate recording, click on the “Finish” button. The files recorded within that time will be saved.If you want to cancel recording, click on the “Cancel” button. When you click the cancel button while recording, you 'll get a message selecting Yes or No. - Page 43 4.4.2 Recording Scheduler This mode is enabled by pressing popup menu(Recording Scheduler). You can easily set the Channel/Date/ start time / Duration/Cycle of the TV program you want to record. Click Insert( ) button and add Recording Schedule list. Click Delete( ) button and delete Recording Schedule list.
-
Page 44: Playing Files
Playing Files If you click on the “open file” button on the controller, you can play a file. You can also select multiple files for playback. Difference between a *.tp and *.tpl file: *.tp files are recorded files that are formatted for HDTV *.tpl file is a file that represents multiple files when one program is recorded to multiple files. -
Page 45: Using Epg
Using EPG 4.7.1 Reserved program List Reserved program list shows the program that you reserved. If you need to cancel reservation, select the program and click Button( Recording Scheduler list shows the program that you reserved.If you need to cancel reservation, select the program and click button( 4.7.2 TitanEPG... - Page 46 member before viewing your channel guides. Most likely there will be an updated version of the TitanEPG Information on Titan web site Please check the site (Http://www.titan.com). 4.7.3 EPG Program The main feature on this page is the programming grid. This grid is divided lengthwise by station/channel number and widthwise by time (in three-hour increments).
- Page 47 1) Execute the FusionHDTV program and right click the “Tray” icon. If you do not see the FusionTray icon in the tray, uncheck ‘Fusion Tray Auto Run’. Start the program by Start->Program->DViCO- >FusionHDTV Agent. Press ‘Hide Menu(C)’, and you can hide popup menu.
-
Page 48: Cut Editing
Cut Editing You can cut the live recording/broadcast files as well as recorded .tp file with the cut-editing feature of the FusionHDTV. 1) The cut-editing window will appear if you hit the ‘Cut’ button. (Mark-in/out button also brings the cut- editing window) 2) You can set the prefix name on the ‘Prefix’... - Page 49 5) To change the file name, just click the file name area. The edit-box will appear and you can type the filename. To change the IN/OUT position, just click the spot you want to change. The edit-box and up/down buttons will appear for you to change the position. To change the hour / minute/ second, click each area you want.
-
Page 50: Using Fusionremote
Using FusionRemote * Optional FusionHDTV remote transceiver. This indicates Remote Buttons. 4.9.1 Using For FusionHDTV PowerDVD start WinAMP start User profile FusionHDTV start Profile start Configuration Input change Before Channel Direction/Enter MCE DVD MENU Alt-Tab Instant forward Instant replay Channel Up/Down Volume Up/Down MCE start/Exit File Open... - Page 51 4.9.2 Using other Windows Œ • Ž Œ Œ • Œ • Œ 1) UP button 2) LEFT button 3) Enter button 4) RIGHT button 5) DOWN button All specifications and information are subject to changes without further notices...
- Page 52 4.9.3 Using Remote profile program 1. WinAMP You can use Fusion Remote as the simple replacement of the keyboard. press the CPF button on the remote transceiver for customizing the remote transceiver keys for the program you selected. WinAMP Start User Profile Change Start profile Show File information...
- Page 53 2. PowerDVD You can use Fusion Remote as the simple replacement of the keyboard. press the CPF button on the remote transceiver for customizing the remote transceiver keys for the program you selected. PowerDVD Start User Profile Change Profile Start Configuration Skin Toggle TAB Key...
- Page 54 3. Window Media Player 9 You can use Fusion Remote as the simple replacement of the keyboard. press the CPF button on the remote transceiver for customizing the remote transceiver keys for the program you selected. User profile Change Profile Start Configuration 반복...
- Page 55 4. Window MCE 2005 You can use Fusion Remote as the simple replacement of the keyboard. press the CPF button on the remote transceiver for customizing the remote transceiver keys for the program you selected. PowerDVD Start WinAMP Start User profile change FusionHDTV Start Profile Start Main Menu...
- Page 56 4.9.4 Using Customize mode When you are not using the FusionHDTV, you can use Fusion Remote as the simple replacement of the keyboard. You can define the key-button mapping of any program you want to use with the FusionRemote. Please refere to the instruction below. 1) Create the profile you want to define like the picture below.
- Page 57 3) After adding the profile please press the <- button to select the profile for key define. 4) Please press the blue button on the remote transceiver for customizing the remote transceiver keys for the program you selected. All specifications and information are subject to changes without further notices...
- Page 58 5) If you press the Customize… button on the picture above you will see the remote transceiver pop up. All specifications and information are subject to changes without further notices...
- Page 59 6) Please press button on the remote transceiver and input the keys or shortcut keys you want to map to the button. Press SaveAll button when you are done 7) Clear button clears the button defined. 8) You can set the OSD setting in accordance to each profile like the picture below. All specifications and information are subject to changes without further notices...
-
Page 60: 4.10 Using Signal Checker
Please do not execute Fusion Program and signal checker at the same time. They only work one at a time. 1) Start – Program– Dvico – FusionHDTV – Signal Checker 2) Press Scan CHs (Scan Channels) button to search the channel. -
Page 61: Using Fusionconverter
You can Convert Tp files to MPEG2,DVD or DivX Files. FusionConverter works in 1080i, 576p, 576i ( FusionHDTV5 Lite model doesn’t support the FusionConverter ) Start->Program->DVICO->FusionConverter 2. Use file open button to select Tp file to convert. Use file save button to locate the converted file to be saved. - Page 62 Use “interlace” option if you watch converted motion file on a TV or on both TV and a PC. Use “MP2” Audio format option if you burn the DVD authoring tool.(Ex. Ulead Videostudio 7 SE DVD) All specifications and information are subject to changes without further notices...
-
Page 63: 4.12 Fusionhdtv Shortcut Key
4.12 FusionHDTV Shortcut Key Shortcut Key Explanation HELP A+Numeric Analog Channel D+Numeric Digital Channel ALT+F4 Exit. ALT+T Time-Shifting On/Off ALT+W Show WallPaper Page Up Fast Foward (FF) Page Down Rewind (REW) Backspace Instant Replay. ALT+Enter Fullscreen CTRL+Space Mute. CTRL+B Repeat all Aspect ratio CTRL+C 16:9,4:3,4:3 Pan &... -
Page 64: Technical Support
Please visit our WEB (http://www.fusionhdtv.co.kr/Eng) and check the enriched FAQs and much more. And please sign-up and let Dvico support you better. If you sign up, you will get: 1) Automatic emailing of FusionHDTV latest update news, tips & techiques.