Specifications - Pioneer A-509R Service Manual

A-509R

8.4 SPECIFICATIONS

Amplifier Section
Continuous power output
(both channels driven at 20 Hz to 20 kHz)**
T.H.D. 0.06 %, 8 Ω ............................................. 45 W + 45 W*
T.H.D. 0.09 %, 4 Ω ............................................. 65 W + 65 W*
DIN Continuous power output (both channels driven at 1 kHz)
T.H.D. 1.0 %, 8 Ω ................................................. 60 W + 60 W
T.H.D. 1.0 %, 4 Ω ................................................. 90 W + 90 W
Total harmonic distortion**
20 Hz to 20 kHz, 20 W, 8 Ω .......................................... 0.05 %*
• Power output specification is for when power supply is
230V.
Input sensitivity/ impedance
PHONO (MM) ..................................................... 2.8 mV/ 50 kΩ
CD, TUNER, LINE/SB, TAPE 1/CD-R/MD,
TAPE 2 MONITOR ............................................ 200 mV/ 50 kΩ
PHONO (MM) overload level
1 kHz, T.H.D. 0.1 % ...................................................... 150 mV
Output level/ impedance
TAPE 1/CD-R/MD, TAPE 2 MONITOR output
............................................................................. 200 mV/ 1 kΩ
Frequency response
PHONO (MM) .................................... 20 Hz to 20 kHz ± 0.5 dB
CD, TUNER, LINE/SB, TAPE 1/CD-R/MD,
TAPE 2 MONITOR .............................. 5 Hz to 100 kHz
Tone control
BASS ............................................................... ± 8 dB (100 Hz)
TREBLE ............................................................ ± 8 dB (10 kHz)
Loudness contour (volume control set at – 30 dB position)
.............................................. + 5 dB (100 Hz)/ + 3 dB (10 kHz)
• ACCESSORIES
Power cord (ADG1154)
30
Signal-to-Noise ratio (IHF short circuit, A network)
PHONO (MM, 5 mV input) .............................................. 86 dB*
CD, TUNER, LINE/SB, TAPE 1/CD-R/MD,
TAPE 2 MONITOR ....................................................... 106 dB*
Signal-to-Noise ratio (DIN, continuous power/ 50 mW)
PHONO (MM) ..................................................... 71 dB/ 67 dB*
CD, TUNER, LINE/SB, TAPE 1/CD-R/MD,
TAPE 2 MONITOR ............................................. 95 dB/ 71 dB*
Power Supply/ Miscellaneous
Power requirements ............................... AC 220 - 230 V, 50/ 60 Hz
Power consumption .............................................................. 160 W
Power consumption in standby mode ....................................... 1 W
AC outlet
Switched(x1) ....................................................................... 100W
Dimensions (including knobs and other protruding parts)
............................................... 420 (W) × 335 (D) × 128 (H) mm
Weight (without package)
......................................................................................... 6.9 kg
Accessories
Remote control unit ........................................................................ 1
Batteries (AA/R6P) ......................................................................... 2
Operating instructions .................................................................... 1
Power cord(Rated current 2.5 A) ................................................... 1
Warranty card ................................................................................ 1
+0
dB*
- 3
NOTE:
Specifications and design subject to possible modification without
notice, due to improvements.
* Measured with the DIRECT/SB MODE button set to on.
(at DIRECT ON mode, SB OFF mode)
** Measured by Audio Spectrum Analyzer.
Batteries (AA/R6P)
(VEM-013)
STANDBY / ON
AMP CD TUNER TAPE
Remote control unit
TAPE 2 7 3
SELECT
I II 1 TAPE ¡
DECK DECK
(CU-A018)
4 ¢ 7 3
CD
_
DISC
+ (AXD7187)
SELECT STATION
TUNER
+
CD TUNER PHONO
VOLUME
TAPE 1 TAPE 2 LINE
STEREO AMPLIFIER Î
REMOTE CONTROL UNIT