Table of Contents
Advertisement
7
REC SELECTOR switch /indicator(For TAPE 1/CD-
R/MD terminals)
This switch is used to select the recording source component.
The signal from the selected component is output at the TAPE1/
CD-R/MD jacks for recording. To select a recording source com-
ponent, press the REC SELECTOR switch so that the indicator
of the desired source component lights up. When this switch is
set to [TUNER] or [CD], the signal from the selected component
can be recorded regardless of the input selector switch and
TAPE2 MONITOR button settings.
CD
: To record from the equipment connected to the CD
terminals.
TUNER : To record from the equipment connected to the
TUNER terminals.
SOURCE : To record from the equipment selected by the IN-
PUT SELECTOR knob.
OFF
: In this position, nothing from the REC terminals of
TAPE 1/CD-R/MD is output. Set to this position when
not recording; the cassette deck will be disconnected,
improving sound quality.
NOTE:
The function selected using the INPUT SELECTOR knob will be
recorded irrespective of the position of the REC SELECTOR
switch (TAPE 2 MONITOR terminals).
8
BALANCE control
Should normally be left in the center position. Adjust the balance
if the sound is louder from one of the speakers. If the right side is
louder, turn toward the L (left) position and if the left side is louder,
turn toward the R (right) position.
NOTE:
This control does not operate at DIRECT ON mode.
9
DIRECT/SB MODE button/indicator
Press and hold the button for more than 3 seconds to switch SB
mode ON. (Volume indicator goes out)
Press and hold the button for more than 3 seconds again to
switch SB mode OFF. (Volume indicator lights)
[DIRECT]
Use this button when you do not wish to pass the output from
input terminal equipment through the various frequency adjust-
ing circuits (BASS, TREBLE, BALANCE, LOUDNESS).
On : The indicator lights. The signals input through the input
terminals are reproduced without passing through the
various frequency adjusting circuits. This results in flat,
pure sound which is a more faithful reproduction of the
input source.
Off : The indicator goes out. The signal passes through the
various frequency adjusting circuits.
[SB MODE]
The SB mode is a special mode in which the amplifier does not
accept remote control except power ON/OFF (But all of the fa-
cilities can be controled by manual as same as SB mode OFF.).
Fix the VOLUME control near the center position.In this mode,
the set can be used as a power amplifier which amplifies the
LINE/SURROUND BACK input (the function name is LINE/SB)
with a input sensitivity of 1V.
For example, when the set is combined with one of Pioneer's
Surround Back compatible receiver, the set can be used sa the
Surround Back amplifier.
(For details, please refer to the instruction manual of the receiver.)
0
LOUDNESS button/indicator
Use when listening at low volume level.
On : The indicator lights. Boosts low and high frequencies to
give added punch to playback even at low volume level.
Off : The indicator goes out. Should normally be left in this
position.
NOTE:
This button does not operate at DIRECT ON mode.
-
TREBLE tone control
Use to adjust the high-frequency tone. The center position is the
flat (normal) position. When turned to the right, the high-frequency
tone is emphasized; when turned to the left, the high-frequency
tone is de-emphasized.
NOTE:
This control does not operate at DIRECT ON mode.
=
BASS tone control
Use to adjust the low-frequency tone. The center position is the
flat (normal) position. When turned to the right, the low-frequency
tone is emphasized; when turned to the left, the low-frequency
tone is de-emphasized.
NOTE:
This control does not operate at DIRECT ON mode.
~
PHONES jack
When using headphones, insert the plug into this jack.
!
SPEAKERS B (ON/OFF) button/indicator
Use this button to listen to the speaker system connected to the
SPEAKERS B terminals.
On : The indicator lights. Sound is heard from the speaker sys-
tem.
Off : The indicator goes out. No sound is heard from the
speaker system. Set to this position when listening with
headphones.
@
SPEAKERS A (ON/OFF) button/indicator
Use this button to listen to the speaker system connected to the
SPEAKERS A terminals.
On : The indicator lights. Sound is heard from the speaker sys-
tem.
Off : The indicator goes out. No sound is heard from the
speaker system. Set to this position when listening with
headphones.
A-509R
27
Hide quick links:
Advertisement
Table of Contents
