Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports RODUCT NTRODUCTION Congratulations on your purchase of the 24‐Port PoE+ Web‐Managed PoE+ Gigabit Ethernet Switch. Before you install and use this product, read this manual carefully for a full understanding of its functions . 2.1 P RODUCT VERVIEW The Web‐Managed Gigabit Ethernet Switch provides a seamless network connection. It ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports • Supports Rapid Spanning Tree/Spanning Tree protocol • Broadcast storm control with multicast packet rate settings • Supports two types of QoS: port‐based and DSCP • LEDs for power, link/activity and PoE • Includes 19" rackmount brackets ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 2.4 E XTERNAL OMPONENT ESCRIPTION 2.4.1 Front Panel The front panel of the Switch consists of 24 x 10/100/1000 Mbps RJ‐45 ports, 2 x SFP ports, 1 x Console port, 1 x Reset button and a series of LED indicators as shown as below. ...
Page 7
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports The following chart shows the LED indicators of the Switch along with explanation of each indicator. LED COLOR STATUS STATUS DESCRIPTION On Power On Power Red Off Power Off ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 2.4.2 Rear Panel AC Power Connector: Power is supplied through an external AC power adapter. It supports AC 100‐240V, 50/60Hz. Grounding Terminal: Ground the switch through the PE cable on the AC cord or with a separate ground wire. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports NSTALLING AND ONNECTING THE WITCH This part describes how to install your Web‐Managed Gigabit Ethernet PoE+ Switch and make connections to it. 3.1 I NSTALLATION The following steps will help prevent damage to the device while also helping to maintain proper security. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Figure 4 ‐ Desktop Installation 3.1.2 Rack‐mountable Installation in 19‐inch Cabinet The switch can be mounted in an EIA standard‐sized, 19‐inch rack, which can be placed in a wiring closet with other equipment. To install the switch, follow these steps: Attach the mounting brackets on the switch’s side panels (one on each side) and secure them with the screws provided. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 3.1.3 Power on the Switch The switch is powered on by connecting it to an outlet using the AC 100‐240V 50/60Hz internal high‐performance power supply. AC Electrical Outlet: It is recommended to use a single‐phase, three‐wire receptacle with a neutral outlet or multifunctional computer professional receptacle. Be sure to connect the metal ground connector to the grounding source on the outlet. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports ONNECTION TO THE WITCH 4.1 C ONNECTING OMPUTER Use standard Cat5/5e Ethernet cable (UTP/STP) to connect the switch to end nodes as described below. Switch ports will automatically adjust to the characteristics (MDI/MDI‐X, speed, duplex) of the device to which they are connected. Figure 7 ‐ PC Connect ...
Page 13
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Open the browser, and go to the URL http://192.168.2.1. The switch login window appears, as shown below. Enter the Username and Password (the factory default Username is admin and Password is admin), and then click “LOGIN” to log in to the switch configuration window as below. 13 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports WITCH ONFIGURATION The PoE+ Web‐Managed Gigabit Ethernet Switch software provides rich Layer 2 functionality for switches in your networks. This chapter describes how to use the Web‐based management interface (Web UI) for this switch. In the Web UI, the left column shows the configuration menu. The top row shows the switch’s current link status. Green squares indicate the port link is up (port 17 in the example above), while black squares indicate the port link is down. Below the switch panel, you can find a common toolbar to provide useful functions for users. The rest of the screen area displays the configuration settings. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.2 Logging Message The Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch is equipped with an extensive logging function. You can define the type of events you wish the switch to log, the level of detail and the target destination for the log. Target: • Buffered: The Log information is stored in the RAM. All messages are lost when the switch loses power or is being restarted. • Flash: Log information is stored in the FLASH memory and will be available after a system ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.3 Port The Port configuration page displays port summary and status information. 5.1.3.1 Port Counters This page displays standard counters of network traffic using modes like Interface, EtherLike and RMON. Interfaces and EtherLike counters display errors on the traffic passing through each port. RMON counters provide a total count of different frame types and sizes passing through each port. Port: Select any of the 24 RJ45 Gigabit Ethernet Ports (GE), 2 SFP ports, or 8 Link Aggregation ...
Page 17
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.3.2 Port Error Disabled Some protocols such as BPDU Guard, Loop back and UDLD can disable ports to protect the rest of the network, for instance if the switch detects that one of the attached network interface cards is malfunctioning and flooding the network with error packets. Ideally, you want this screen to look as shown below. 5.1.3.3 Bandwidth Utilization This page displays the TX (transmit) and RX (receive) bandwidth utilization for each port. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.4 Link Aggregation Link aggregation is a method of using multiple Ethernet ports in parallel to increase throughput beyond what a single connection could sustain, and to provide redundancy in case one of the links should fail. As this is essentially a grouping of ports into one logical unit, we call them Link Aggregation Groups, or “LAG” for short. Any LAG that is currently defined will be shown on this screen. The configuration of the LAG will be addressed later in the section “Switching”. 18 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.5 LLDP Statistics The Link Layer Discovery Protocol (LLDP) is a vendor‐neutral link layer protocol in the Internet Protocol Suite used by network devices for advertising their identity, capabilities, and neighbors on an IEEE 802 local area network, principally wired Ethernet. The LLDP statistics page displays an overall summary and per‐port information for LLDP frames transmitted and received on the switch. Insertions: The number of times the complete set of information advertised by a particular MAC Service Access Point (MSAP) has been inserted into tables associated with the remote systems. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.1.6 IGMP Snooping Statistics The Internet Group Management Protocol (IGMP) is a communications protocol used by hosts and adjacent routers on IP networks to establish multicast group memberships. IGMP is an integral part of IP multicast. IGMP can be used for one‐to‐many networking applications such as online streaming video and gaming, and allows more efficient use of resources when supporting these types of applications. This page displays the IGMP statistics information, also referred to as ‘Snooping Statistics’. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.2 N ETWORK Use the Network page to configure settings for the switch network interface and set up the time related settings. 5.2.1 IP Address Define the IP address of the switch here. Mode: Select the mode of network connection. •...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.2.2 Time Settings 5.2.2.1 System Time For the switch to accurately flag messages with the correct date and time stamp, the switch’s system time must be set up first. Set “Enable SNTP” to “Disabled” if you do not want to sync the switch system time with an external time server, but rather want to configure it manually. 5.2.2.2 SNTP Settings If you wish to synchronize the switch system time with an external time server, also referred to as an NTP or SNTP server, then you can provide the IP address or host name of said server ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3 S WITCHING 5.3.1 Port Setting On this screen you can configure basic aspects of each of the ports. Port Select: Select one or multiple ports to configure. Enabled: ...
Page 25
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Duplex: In a full duplex system, both parties can communicate to the other simultaneously. An example of a full‐duplex device is a telephone; the parties at both ends of a call can speak and be heard by the other party simultaneously. In networking terms, full duplex allows receiving and transmitting of data at the same time, whereas half duplex does not. If the telephone is an example for full duplex, then a push‐to‐talk CB radio or ‘walkie‐talkie’ represents half duplex. The switch can either receive or send data, but it can never happen simultaneously. Unless you have any specific reason not to do so, this should be left in “Auto” mode. Flow Control: ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.2 Error Disabled This page allows you to define the parameters for the automatic port disable function. Recovery Interval: The switch will automatically re‐enable ports that have been previously disabled, after the recovery interval time has elapsed. BPDU Guard: BPDUs are sent out as multicast frames to which only other layer 2 switches or bridges are listening. If any loops (multiple possible paths between switches) are found in the network topology, the switches will co‐operate to disable a port or ports to ensure that there are no loops. Flood: The network can get overwhelmed by a large amount of unicast packets that can ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.3 Traffic Mirroring Port mirroring is the ability of a network switch to send a copy of network packets seen on a switch port or ports to a network‐monitoring device connected to another switch port, i.e., a computer equipped with a packet sniffer utility. Session ID: The Intellinet switch supports up to 4 session IDs. Monitor Session State: Disables or enables port mirroring for this session. Destination Port: The port to which the mirrored packets are sent, which is the port to which you connect your network monitoring station. This port will no longer function as a regular port, and it cannot be assigned to any LAG or VLAN group. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.4 Link Aggregation 5.3.4.1 LAG Setting Besides providing a higher speed connection to another port by grouping ports together into la logical unit, Link Aggregation (LAG) also provides a load balancing feature. On this screen you define whether LAG that is depended on the MAC address or IP/MAC address. 5.3.4.2 LAG Management ...
Page 29
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Static: All configuration settings must be set up manually exactly the same way on the participating LAG device, i.e., the other Intellinet 24 Port PoE+ Web Managed Gigabit Switch. There is no problem with doing this of course. Even the static method provides link redundancy, should one or more of the links in the trunk fail. However, if media converters are used, it can happen that the link on the switch#1 is up, but the connection to the switch#2 at the other end is interrupted, for example because of a cable malfunction. In this case, switch#1 keeps sending data via this connection, because on this end there are no interruptions. The data transfer is therefore interrupted. LACP: Link Aggregation Control Protocol (LACP) allows the dynamic exchange of information with regard to the link aggregation between the two members of said aggregation. It allows for the automatic detection of links in an LAG group when connected to another LACP‐...
Page 30
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.4.4 LACP Setting This page is used to configure the system LACP system priority, which determines which switch (switch #1 or switch #2) in an LACP link controls port priorities. If both switches are set to the default value “1,” then the LACP system ID (MAC address of the switch) determines which of the switches is in charge. Other than that, the switch with the lowest system priority number is in control. 5.3.4.5 LACP Port Setting This page is used to set the priority for the LACP member ports. While the system priority defines, which switch is in charge in the LACP setup, the port priority is used to determine, ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.5 VLAN Management 5.3.5.1 Create VLAN This page allows adding, deleting or editing the switch’s VLAN settings. VLAN LIST: This is he ID for the new VLAN. VLAN Action: Add or delete the VLAN. VLAN Name Prefix: VLAN Name Prefix for the new VLAN. Below is a real‐world example: ...
Page 33
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.5.2 Interface Settings This page allows the user to set the port type of vlan, common have access and trunk, dot1q ‐ tunnel three modes and native VLAN choose whether the port TX,RX should have a tag. Port Select : Select one or multipleports to configure. Interface VLAN Mode: VLAN port mode Hybrid: Port hybrid model. Access: Port hybrid model. Trunk: Port hybrid model. ...
Page 34
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.5.3 Port to VLAN To display Port to VLAN web page, click Switching > VLAN Management > Port to VLAN Make port add to VLAN ,select the port’s different behaviors when it works under the VLAN. 5.3.5.4 Port VLAN Membership To display Port VLAN Membership web page, click Switching > VLAN Management > Port VLAN Membership ...
Page 35
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.5.5 Protocol VLAN Group Setting To display Protocol VLAN Group Setting web page, click Switching> VLAN> Protocol VLAN Group Setting The VLAN group setting,that is sets the same type message as a group and transmit it in the specific VLAN. Group ID(1‐8) : Enter an ID number of the group, between 1 and 8. ...
Page 36
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.5.6 Protocol VLAN Port Setting To display Protocol VLAN Port Setting web page, click Switching> VLAN> Protocol VLAN Port Setting This page is used to divide the port into groups and map it to the VLAN. Port: Select the specified ports you wish to configure by selecting the port in this list. Group: Click the corresponding radio button to select a previously configured Group ID or Group Name. VLAN :Click the corresponding radio button to select a previously configured VLAN ID or VLAN Name. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.6 Multicast 5.3.6.1 Properties To display Properties web page, click Switching > Multicast > Properties This page is used to Set message behavior and iPv4 message forwarding rules. 5.3.6.2 IGMP Snooping ...
Page 38
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports IGMP Snooping Version: Select the IGMP Snooping Version,IGMPv2 or IGMPv3. IGMP Snooping Report Suppression:Select the IGMP Snooping Report Suppression enable or disable. IGMP Snooping Querier Setting To display IGMP Snooping Querier Setting web page, click Switching > Multicast > IGMP Snooping > IGMP Snooping Querier Setting VLAN ID: Select the VLANs to configure. Querier State: Set the enabling status of IGMP Querier Election on the chose VLANs. Enable: Enable IGMP Querier Election. ...
Page 39
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports IGMP Group Table To display IGMP Group Table web page, click Switching > Multicast > IGMP Snooping > IGMP Group Table This page is used to display IGMP Group Table statistics information. 39 ...
Page 40
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports IGMP Router Port Setting To display IGMP Router Port Setting web page, click Switching > Multicast > IGMP Snooping > IGMP Router Port Setting This page is used to configure specified ports as static route ports. 40 ...
Page 41
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports IGMP Router Table To display IGMP Router Table web page, click Switching > Multicast > IGMP Snooping > IGMP Router Table This page is used to display IGMP Router Table statistics information. IGMP Forward All To display IGMP Forward All web page, click Switching > Multicast > IGMP Snooping > IGMP Forward All ...
Page 42
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.6.3 Multicast Port Max‐Groups To display Multicast Port Max‐Groups web page, click Switching > Multicast >Multicast Port Max‐Groups This page is used to Limit the port can join one of the biggest Multicast instance. 42 ...
Page 43
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Multicast Filter This page allow user to Create filter instance. Multicast Profile Setting To display Multicast Profile Setting web page, click Switching > Multicast >Multicast Filter > Multicast Profile Setting Multicast Profile Setting To display IGMP Filter Setting web page, click Switching > Multicast > Multicast Filter > IGMP Filter Setting This page is used to Filter on the port to bind to that instance. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.3.7 Jumbo Frame To display Jum bo Frame web page, click Switching > Jumbo Frame Jumbo Frame: Jumbo frame size. The valid range is 0 bytes – 9216 bytes. STP The Spanning Tree Protocol (STP) is a network protocol that ensures a loop‐free topology for any bridged Ethernet local area network. STP Global Setting To display STP Global Setting web page, click Switching > STP > STP Global Setting ...
Page 45
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports STP‐Compatible: 802.1D STP operation. RSTP‐Operation: 802.1w operation. MSTP‐Operation: 802.1s operation. Configuration Revision: Set the Revision of the Configuration Identification. (Range:0‐65535). STP Port Setting To display STP Port Setting web page, click Switching > STP > STP Port Setting Port Select: Select the port list to specify which ports should apply this setting. ...
Page 46
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Yes: Enable BPDU filter function. To drop directly the received BPDU from the specified ports. P2P MAC: Set the Point‐to‐Point port configuration. No: Force to false state. Yes: Force to true state. Migrate: Force to try to use the new MST/RST BPDUs, and hence to test the hypothesis that all legacy systems that do not understand the new BPDU formats have been removed from the LAN segment on the port(s). CIST Instance Setting ...
Page 47
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports To display CIST Port Setting web page, click Switching > STP > CIST Port Setting Port Select : Select the port list to specify which ports should apply this setting. Priority: Set the Port Priority to the selected ports in the specified CIST instance. Internal Path Cost: Set the Internal Path Cost to the selected ports in the specified CIST instance. (0 means `Auto`) MST Instance Setting To display MST Instance Setting web page, click Switching > STP > MST Instance Setting ...
Page 48
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Priority: Set the Bridge Priority in the specified MST instance. MST Port Setting To display MST Port Setting web page, click Switching > STP > MST Port Setting MST ID: Set the MSTI ID to specify MST instance. Port Select : Select the port list to specify which ports should apply this setting. Priority: Set the Port Priority to the selected ports in the specified MST instance. Internal Path Cost: Set the Internal Path Cost tot he selected ports in the specified MST instance. (0 means `Auto`) ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.4 M AC DDRESS ABLE Static Mac Setting To display Static Mac Setting web page, click Mac Address Table > Static Mac Setting MAC Address: The MAC address to which packets will be statically forwarded. If Type is unicast, enter unicast MAC address in this field;If Type is multicast, enter multicast MAC address in this field. ...
Page 51
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports This page is used to set the MAC address of the aging time to study Aging Time: Set the time needed for aging Dynamic Learned To display Dynamic Learned web page, click Mac Address Table > Dynamic Learned Port: Select the port number to show or clear dynamic MAC entries. If not select any port, VLAN and MAC address, the whole dynamic MAC table will be displayed or cleared. VLAN: Select the VLAN to show or clear dynamic MAC entries. If not select any port, VLAN and MAC address, the whole dynamic MAC table will be displayed or cleared. ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.5 S ECURITY Use the Security pages to configure settings for the switch security features. Storm Control Global Setting To display Global Setting web page, click Security > Storm Control > Global Setting Unit: Choose to storm control unit is the pps or bps Preamble & IFG: Select the rate calculates w/o preamble & IFG (20 bytes). Excluded: exclude preamble & IFG (20 bytes) when count ingress storm control rate. ...
Page 54
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Port: Select the setting ports. Type Enable: Select the type of storm control. Broadcast: Broadcast packet. Unknown Multicast: Unknown multicast packet State. Unknown Unicast: Unknown unicast packet. Rate: Value of storm control rate, Unit: pps (packet per‐second) or Kbps (Kbits per‐second) depends on global mode setting. The range is from 0 to 1000000. ...
Page 55
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 802.1X: Set the enabling status of 802.1X functionality. Enable: Enable 802.1X. Disable: Disable 802.1X. 802.1X Port Setting To display 802.1X Port Setting web page, click Security > 802.1X > 802.1X Port Setting Port: Select the ports to configure their authentication mode. Mode: The authentication mode. ...
Page 56
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports No Authentication:802.1X disabled. Reauthentication Enable: Set the enabling status of802.1X reauthentication. Reauthentication Period: Set the reauthentication period of 802.1X if reauthentication is enabled. Guest VLAN Setting To display Guest VLAN Setting web page, click Security > 802.1X > Guest VLAN Setting Authenticated Hosts To display Authenticated Hosts web page, click Security > 802.1X > Authenticated Hosts DHCP Snooping ...
Page 57
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports ports can receive and forward the DHCP Offer message, on the contrary, the discreditable port will lose the DHCP Offer message. In that way, the switch can pick out the fake DHCP Server and make sure that the client gets legal IP address from DHCP Server. Global Setting To display Global Setting web page, click Security > DHCP Snooping > Global Setting This page is used to open DHCP Snooping function DHCP Snooping: enable or disable DHCP Snooping function VLAN Setting To display VLAN Setting web page, click Security > DHCP Snooping > VLAN Setting Specific VLAN starts DHCP Snooping Port Setting ...
Page 58
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports To display Port Setting web page, click Security > DHCP Snooping > Port Setting This page allow user to make the specific port is configured for DHCP Snooping trust port. Statistics To display Statistics web page, click Security > DHCP Snooping > Statistics This page statistics of each port of DHCP Snooping state information. Rate Limit To display Rate Limit web page, click Security > DHCP Snooping > Rate Limit 58 ...
Page 59
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Option82 Global Setting To display Option82 Global Setting web page, click Security> DHCP Snooping > Option82 Global Setting This page is used to configure DHCP Snooping support Option82 strategy. Option82 Port Setting To display Option82 Port Setting web page, click Security> DHCP Snooping > Option82 Port Setting To the specified port configuration of receiving containing Option 82 options request packet port handling strategy. ...
Page 60
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Option82 Circuit‐ID Setting To display Option82 Circuit‐ID Setting web page, click Security> DHCP Snooping > Option82 Circuit‐ID Setting This page allow user to edit circuit ID content in the option82. Port Security To display Port Security web page, click Security> Port Security Ports Security, it can set port isolation and specific behavior. 60 ...
Page 61
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Port Select: Select one or multipleports to configure. Security: Port security function. It constraint how many MAC addresses can be learned by a port and drop new one when reach the limitation. Enable: Enable port security function. Disable: Disable port security function. Max L2 Entry: The total number of MAC addresses entry which can be learn by a port. AAA Login List ...
Page 62
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports List Name: New login authentication list name. This name should be different from other existing lists. Method 1: Select first priority of login authentication method. Local: Use local accounts database to authenticate. Tacacs+: Use remote TACACS+ server to authenticate. Radius: Use remote Radius server to authenticate. Not supported now, it will besupported in the future. Enable: Use local enable password to authenticate. ...
Page 63
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Tacacs+: Use remote TACACS+ server to authenticate. Radius: Use remote Radius server to authenticate. Not supported now, it will besupported in the future. Enable: Use local enable password to authenticate Enable List To display Login List web page, click Security> AAA > Enable List This page allow user to add, editor delete enable authentication list settings (The “default” list cannot be deleted.). The line combined to this list will authenticate user who issuing the‘enable’ command by methods in this list. If the first method is failed, it will try to use the next priority method to authenticate if it exists. ...
Page 64
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Tacacs+: Use remote TACACS+ server to authenticate. Radius: Use remote Radius server to authenticate. Not supported now, it will besupported in the future. Accounting List To display Accounting List web page, click Security> AAA > Accounting List This page allow user to add, editor delete accounting list settings (The “default” list cannot be deleted.). The line combined to this list will accounting user who entering CLI shell by methods in this list. If the first method is failed, it will try to use the next priority method to accounting if it exists. List Name: New accounting list name. This name should be different from other existing lists. ...
Page 65
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Tacacs+ Server To display Tacacs+ server web page, click Security> AAA >Tacacs+ server This page allow user to add, edit or delete TACACS+ server settings. Radius server To display Radius server web page, click Security > AAA > Radius server This page is used to set about radius server. 65 ...
Page 66
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Access Console To display Console web page, click Security > Access > Console This page allow user to combine all kinds of AAA lists to console line. The user accesses switch from console will be authenticated, authorized and accounted by AAA lists we combined here. Login Authentication List: Select one of the login authentication lists we configured in “Login List” page. Enable Authentication List: Select one of the enable authentication lists we configured in ...
Page 67
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports EXEC Authorization List: Select one of the EXEC authorization lists we configured in “EXEC List” page. Commands Authorization List: Select one of the commands authorization lists we configured in “Commands List” page. EXEC Accounting List: Select one of the EXEC accounting lists we configured in “Accounting List” page. Session Timeout: Set session timeout minutes for user access CLI from console line. If user does not response after session timeout minute, CLI will logout automatically. 0 minutes means never timeout. ...
Page 68
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Commands Authorization List: Select one of the commands authorization lists we configured in “Commands List” page. EXEC Accounting List: Select one of the EXEC accounting lists we configured in “Accounting List” page. Session Timeout: Set session timeout minutes for user access CLI from telnet line. If user does not response after session timeout minute, CLI will logout automatically. HTTP To display HTTP web page, click Security > Access > HTTP This page allow user to combine all kinds of AAA lists to HTTP line. The user accesses switch WEBUI from HTTP will be authenticated by AAA lists we combined here. ...
Page 69
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports HTTPS Server: Set HTTPS Server disable or enable. Login Authentication List: Select one of the login authentication lists we configured in “Login List” page. Session Timeout: Set session timeout minutes for user access WEB from HTTPS protocol. If user does not response after session timeout minute, WEBUI will logout automatically. 0 minutes means never timeout. 69 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.6 ACL MAC‐Based ACL To display MAC‐Based ACL web page, click ACL > MAC‐Based ACL This page allow user to set name for MAC‐Based ACL. ACL Name: Enter ACL name in this field. MAC‐Based ACE To display MAC‐Based ACE web page, click ACL > MAC‐Based ACE This page allow user to set Based on MAC address expanding ACL list, matching corresponding MAC and setting the ports as drop or forward. IPv4‐Based ACL ...
Page 71
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports IPv4‐Based ACE To display IPv4‐Based ACE web page, click ACL > IPv4‐Based ACE This page allow user to set Based on IPv4 expanding ACL Peer Guardian and matching corresponding IP and setting the port as drop or forward. ACL Binding To display ACL Binding web page, click ACL > ACL Binding This page allow user to Bounding with accordingly ACL rules, port bounding ACL rules. 71 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.7 Q S Use the QoS pages to configure settings for the switch QoS interface and how the switch connects to a remote server to get services. General QoS Properties To display QoS properties web page, click QoS > General > QoS properties This page allow user to set QoS mode such basic or advanced. Port Settings ...
Page 74
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Queue Settings To display Queue Setting web page, click QoS > General > Queue Settings This page allow user to set Set the QoS instance queue scheduling model. COS Mapping To display COS Mapping web page, click QoS > General > COS Mapping The page allow user to set QoS instance of COS Mapping. ...
Page 75
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports The page allow user to set QoS instance of DSCP Mapping. IP Precedence Mapping To display IP Precedence Mapping web page, click QoS > General > IP Precedence The page allow user to set QoS instance of IP Precedence Mapping. QoS Basic Mode Global Settings To display Global Settings web page, click QoS > QoS Basic Mode > Global Settings This page allow user to set QoS for trust mode on basic mode global settings. 75 ...
Page 76
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Port Settings To display Port Settings web page, click QoS > QoS Basic Mode > Port Settings This page allow user to set QoS port setting enabled or disabled. QoS Advanced Mode Global Settings To display Global Settings web page, click QoS > QoS Advanced Mode > Global Settings This page allow user to set the default QoS mode state under advanced mode global settings trust mode. 76 ...
Page 77
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Class Mapping To display Class Mapping web page, click QoS > QoS Advanced Mode > Class Mapping This page allow user to create a QoS class which is used to link the ACL. Aggregate Policer To display Aggregate Policer web page, click QoS > QoS Advanced Mode > Aggregate Policer 77 ...
Page 78
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Policy Table To display Policy Table web page, click QoS > QoS Advanced Mode > Policy Table Policy Class Maps To display Policy Class Maps web page, click QoS > QoS Advanced Mode > Policy Class Maps 78 ...
Page 79
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Policy Binding To display Policy Binding web page, click QoS > QoS Advanced Mode > Policy Binding Rate Limit Ingress Port Settings To display Ingress Port Settings web page, click QoS > Rate Limit > Ingress Port Settings This page allow user to set ingress port monitor. 79 ...
Page 80
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Ingress VLAN Settings To display Ingress VLAN Settings web page, click QoS > Rate Limit > Ingress VLAN Settings This page is used to set the bandwidth of the VLAN entry control. Egress Port Settings To display Egress Port Settings web page, click QoS > Rate Limit > Egress Port Settings This page is used to set the egress port monitor. 80 ...
Page 81
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Egress Queue Settings To display Egress Queue Settings web page, click QoS > Rate Limit > Egress Queue Settings The page is used to set the egress lined up bandwidth monitor. 81 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.8 M ANAGEMENT POE POE Global Setting To display POE Global Setting web page, click Management > POE > POE Global Setting This page is used to check POE Status, you can set Max Available Power here. MAX Available Power: Switch configuration can provide maximum power. System Operation Status:display POE operation status on or off ...
Page 83
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Port Select: Select specific ports. Priority: Setting the priority of POE. Critical High Low Power Budget: POE port estimation can provide power. POE Delay Setting To display POE Global Setting web page, click Management > POE > POE Delay Setting This page is for setting POE Power Delay. 83 ...
Page 84
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Port Select: Select specific ports. Delay Mode: enable or disable delay mode. Delay Time: Configuration delay time. LLDP LLDP is a one‐way protocol; there are no request/response sequences. Information is advertised by stations implementing the transmit function, and is received and processed by stations implementing the receive function. LLDP Global Settings To display LLDP Global Settings web page, click Management > LLDP > LLDP Global Settings 84 ...
Page 85
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Enabled: Enable/ Disable LLDP protocol on this switch. Transmission Interval: Select the interval at which frames are transmitted. Thedefault is 30 seconds, and the valid range is 5–32768 seconds. Holdtime Multiplier: Select the multiplier onthe transmit interval to assign to TTL (range 2–10, default = 4). Reinitialization Delay: Select the delay before a re‐initialization (range 1–10 seconds, default = 2). LLDP Port Settings To display LLDP Port Settings web page, click Management > LLDP > LLDP Port Settings ...
Page 86
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports To display LLDP Local Device web page, click Management > LLDP > LLDP Local Device Use the LLDP Local Device page to view information about devices on the network for which the switch has received LLDP information. LLDP Remote Device To display LLDP Remote Device web page, click Management > LLDP > LLDP Remote Device Use the LLDP Remote Device page to view information about remote devices for which the switch has received LLDP information. LLDP Network Policy To display LLDP Network Policy web page, click Management > LLDP > LLDP Network Policy ...
Page 87
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports MED Port Setting To display MED Port Setting web page, click Management > LLDP > MED Port Setting LLDP Overloading To display LLDP Overloading web page, click Management > LLDP > LLDP Overloading 87 ...
Page 89
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports This page is used to configure SNMP view.Used in the SNMP message Management variables (OID) to describe the switch in the Management object,MIB (Management Information Base,Management Information Base) is a set of the monitoring network equipment Management variables.View is used to control variable is how to be managed. SNMP Access Group To display SNMP Access Group web page, click Management > SNMP > SNMP Access Group This page is used to configure SNMP group ,Within the group by the user read‐only, only write, inform the view to achieve the goal of access control. SNMP Community To display SNMP Community web page, click Management > SNMP > SNMP Community 89 ...
Page 90
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports SNMP v1 and the SNMP v2c USES the group Name (Community Name) certification, the group has played a role similar to the password.If use SNMP v1 and SNMP v2c, after configuration view, can be directly on this page to configure SNMP community. SNMP User To display SNMP User web page, click Management > SNMP > SNMP User This page is used to create SNMP user under the group,And the group with the same level of security and access control permissions. SNMPv1,2 Notifcation Recipients To display SNMPv1,2 Notifcation Recipients web page, click Management > SNMP > SNMPv1,2 Notifcation Recipients ...
Page 91
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports SNMPv3 Notification Recipients To display SNMPv3 Notification Recipients web page, click Management > SNMP > SNMPv3 Notification Recipients SNMP Engine ID To display SNMP Engine ID web page, click Management > SNMP > SNMP Engine ID 91 ...
Page 92
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports SNMP Remote Engine ID To display SNMP Remote Engine ID web page, click Management > SNMP > SNMP Remote Engine ID RMON RMON Statistics To display RMON Statistics web page, click Management > RMON > RMON Statistics 92 ...
Page 93
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports RMON Event To display RMON Event web page, click Management > RMON > RMON Event This page is used to configure RMON event group. RMON Event Log To display RMON Event Logweb page, click Management > RMON > RMON Event Log 93 ...
Page 94
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports RMON Alarm To display RMON Alarm web page, click Management > RMON > RMON Alarm This page is used to configure RMON statistics group and alarm group. RMON History To display RMON History web page, click Management > RMON > RMON History This page is used to configure the PMON history group. 94 ...
Page 95
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports RMON History Log To display RMON History Log web page, click Management > RMON > RMON History Log 95 ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.9 D IAGNOSTICS Use the Diagnostics pages to configure settings for the switch diagnostics feature or operating diagnostic utilities. System Status To display System Status Log web page, click Diagnostics > System Status Ping Test To display Ping Test Log web page, click Diagnostics > Ping Test ...
Page 97
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Logging Service To display Logging Service web page, click Diagnostics > Logging Setting > Logging Service Local Logging To display Local Logging web page, click Diagnostics > Logging Setting > Local Logging Target: Select the target to store log message RAM: Store log messages in RAM disk. All log messages will disappear after system reboot. FLASH: Store log messages in FLASH. All log messages will not disappear after system reboot. ...
Page 98
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Server Address: The IP address of remote log server. Server Port:The Port number of remote log server. Severity: Select severity of log messages which will be sent. Factory Default To display Factory Default web page, click Diagnostics > Factory Default This page allow user to restore switch to factory default by pushing “Restore” button. Reboot Switch ...
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports 5.10 M AINTENANCE Use the Maintenance pages to configure settings for the switch network interface and how the switch connects to a remote server to get services. Backup Manager To display Backup Manager web page, click Maintenance > Backup Manager This page allow user to backup the firmware image or configuration file on the switch to remote TFTP server or host file system through HTTP protocol. ...
Page 100
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Backup Method: Select backup method TFTP: Use TFTP to backup HTTP: Use HTTP to backup Server IP: IP address of the TFTP server. If the TFTP backup method is selected, the IP address of the TFTP server must be assigned. Backup Type: Select Backup Type Upgrade Manager To display Upgrade Manager web page, click Maintenance > Upgrade Manager ...
Page 101
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Upgrade Method: Select upgrade method TFTP: Use TFTP to upgrade HTTP: Use HTTP to upgrade Server IP: IP address of the TFTP server. If the TFTP upgrade method is selected, the IP address of the TFTP server must be assigned. File Name: Firmware image or configuration file name on remote TFTP server. If the TFTP upgrade method is selected, the file name must be specified. Browse file: If the HTTP upgrade method is selected, the browse file field allow you to select ...
Page 102
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Configuration Manager To display Configuration Manager web page, click Maintenance > Configuration Manager Account Manager To display Account Manager web page, click Maintenance > Account Manager This page allow user to add or delete switch local user database for authenticating. 102 ...
Page 103
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports User Name: User name for new account. Password Type: Select password type for new account. Clear Text: Password without encryption Encrypted: Password with encryption No Password: No password for the new account. Password: If the password type is not “No Password”, the password must be specified. ...
Page 104
Intellinet 24‐Port Gigabit Ethernet PoE+ Web‐Managed Switch with 2 SFP Ports Clear Text: Password without encryption Encrypted: Password with encryption No Password: No password for the new account. Password: If the password type is not “No Password”, the password must be specified. Retype Password: Retype password to make sure the password is exactly you typed before in “Password” field. Privilege Type: Select privilege level for new account. ...