Advertisement
Master View
CPU Switch
CS-102/CS-122
User's Manual
Packing Checklist
1 CS-102 or CS-122 CPU Switch
1 User's Manual
Please read this manual thoroughly and follow the installation procedures carefully to prevent any
damage to the CS-102/CS-122 and/or the devices it connects to.
©Copyright 1995 Aten® International Co., Ltd.
Manual Part No. PAPE-0135-100
Printed in Taiwan 08/95
All brand names and trademarks are the registered property of their respective owners.
Advertisement
Table of Contents
Related Manuals for ATEN Master View CS-102
Summary of Contents for ATEN Master View CS-102
-
Page 1: Packing Checklist
1 CS-102 or CS-122 CPU Switch 1 User's Manual Please read this manual thoroughly and follow the installation procedures carefully to prevent any damage to the CS-102/CS-122 and/or the devices it connects to. ©Copyright 1995 Aten® International Co., Ltd. Manual Part No. PAPE-0135-100 Printed in Taiwan 08/95 All brand names and trademarks are the registered property of their respective owners. - Page 2 Introduction The CS-102 or CS-122 CPU Switch is a controller for one user to access multiple computers. Before the development of the Master View, the only way to control multiple computer configurations from a single console was through a complex and costly network system.
-
Page 3: Specifications
LEDs Scan Interval Keyboard Connector Mouse Connector PS/2 Mouse Connector Monitor Connector Enclosure Weight Dimensions (L x W x H) CS-102 CS-122 CS-122 Side View Specification DC 9V 160mA (max.) Keyboard/Button 1 Power 2 Ready 2 Select 3, 10, 20, 40 Sec. -
Page 4: Installation
CS-104s and CS-106s. One Stage Installation A One Stage Installation enables one CS-102 or CS-122 to control up to two computers, as shown in Fig. A, below. 1. Set DIP switch 4 to ON. 2. Connect the monitor output port, mouse port, and keyboard port of the computer to either of the PC ports on the CPU SWITCH with appropriate cables. -
Page 5: Two Stage Installation
Note: 1. Add a power adapter if the CPU Switch works abnormally. 2. Neither the PC1 or PC2 port of a CS-102 or CS-122 can be connected to a CS-104 or CS-106. 3. For PS/2 users: You must connect a PS/2 mouse, because a serial mouse can not replace a PS/2 mouse. For cascaded operation, connect PS/2 mouse ports of successive stages using a 6-pin mini-DIN male-to-male cable. -
Page 6: Three Stage Installation
Adding a third stage enables one CPU Switch (the first stage CS-104 or CS-106) to control computers directly or indirectly via cascaded CPU Switches (the second and third stage CS-102, CS-104 or CS-106). The number of PCs under control is determined by the configuration. -
Page 7: Operation
Operation There are two ways to access any computer on the installation: by pressing the front panel SELECT BUTTON, or by entering Hot Keys from the keyboard. Once a computer has been accessed, the CPU Switch directs keyboard control, mouse control, and video image of that computer to you as if the computer were right next to you. - Page 8 # represents the port number on the third stage switch that the computer you wish to access is attached to. Note: # is a digit between 1 and 6 for a CS-106; 1 and 4 for a CS-104; and 1 and 2 for a CS-102/CS-122. 4. Hot Key Summary: Hot Key functions are summarized in the table, below: Ÿ...
-
Page 9: Dip Switch Setting
Port Connects to a Computer Under Scan Mode DIP Switch Setting Scan Time is determined by the DIP Switch of the First Stage* CPU Switch. For the second and the third-stage CS-102/122 units, all DIP switches are set to Off. -
Page 10: Troubleshooting
For further inquires please contact your direct vendor. Cause Set the First Stage CS-102/CS-122 DIP Switch 4 to ON; for all other (cascaded) CS-102 units, set DIP Switch 4 to OFF. Press the Spacebar to exit Scan Mode or Previous/Next Mode.
Need help?
Do you have a question about the Master View CS-102 and is the answer not in the manual?
Questions and answers