Download Print this page

Advertisement

Quick Links

© Panduit Corp. 2010
The Windows driver for the TDP43MY printer can be installed from your Pan-Mark or Easy-Mark software CD or
downloaded from http://www.panduit.com then under Product Information, select Downloads.
Adding TDP43MY printer driver to Windows XP/ Vista 32/64 bit using USB connection:
1.
Obtain the TDP43MY Vista driver (TDP43MY_Vista_Drv_4611.exe) from the Web or Easy-Mark CD.
Double click or run the above program. When prompted "An unidentified program wants access to your computer" select
2.
"Allow". (Windows Vista only).
On the next screen click on the "Setup" button.
3.
The Installation wizard will appear. Click "Next >"
4.
Select "TDP43MY" on the right box and click "Next >"
5.
In the Options screen select "USB001" and click Finish.
6.
7.
The installation wizard will close automatically meaning the installation of the drive was successful.
Note: When you connect the printer for the first time you will get the "Found New Hardware" wizard. Leave this window
8.
open until you install the driver (steps 1-7). When complete select "Don't show this message again for this device."
Windows will send a message "The hardware could not install successfully". Ignore this message as the hardware and
9.
driver are installed.
Adding TDP43MY printer driver to Windows NT/2000 using Parallel or Serial Port:
1.
After installing Easy-Mark or Pan-Mark, go to Start/Printers and Faxes, click Add A Printer.
2.
Follow Install Wizard.
At Install Printer Software – Select "Have Disk" & "Browse".
3.
4.
The TDP43MY is located in either of the following directories:
a.
Easy-Mark: C:\Program Files\Easy-Mark\Printer Drivers\TDP43M
b.
Pan-Mark: C:\Program Files\pmus\drivers\TDP43M
5.
Double click OEMSETUP.inf
6.
Click OK, then Next until you get to Finish. Click Finish.
7.
Continue with Printer Settings listed below
Adding TDP43MY printer driver to Windows 98/ME if using Parallel or Serial Port:
1.
After installing Easy-Mark or Pan-Mark, go to Start/Settings/Printers, select Add Printer.
2.
Follow the install Wizard.
At Install Printer Software select "Have Disk" & "Browse".
3.
4.
The TDP43MY driver is located in either of the following directories:
a.
Easy-Mark: C:\Programs Files\Easy-Mark\Printer Drivers\TDP43M
b.
Pan-Mark: C:\Program Files\pmus\Drivers\TDP43M
5.
Double click OEMSETUP.inf
6.
Click OK, then Next until you get to Finish. Click Finish.
7.
Continue with Printer Settings listed below.
NOTE: In the interest of higher quality and value, Panduit products are continually being
improved and updated. Consequently, pictures may vary from the enclosed product.
Website: www.panduit.com
Email: cs@panduit.com
EU Website:
www.panduit.com/emea
EU Email:
emeatoolservicecenter
@panduit.com
TDP43MY Quick Guide
Panduit Corp. • USA Headquarters • Tinley Park, IL
Tel: 888-506-5400, ext. 3255 • Fax: 630-759-7532
Panduit Europe • EMEA Service Center
Tel: +31 (0) 546 580 452 • Fax: +31 (0) 546 580 441
PA26235A01
Rev. 01 3-2010

Advertisement

loading

Summary of Contents for Panduit TDP43MY

  • Page 1 Rev. 01 3-2010 © Panduit Corp. 2010 The Windows driver for the TDP43MY printer can be installed from your Pan-Mark or Easy-Mark software CD or downloaded from http://www.panduit.com then under Product Information, select Downloads. Adding TDP43MY printer driver to Windows XP/ Vista 32/64 bit using USB connection: Obtain the TDP43MY Vista driver (TDP43MY_Vista_Drv_4611.exe) from the Web or Easy-Mark CD.
  • Page 2 2. Insert ribbon core notches into drive. right side first. Ensure ribbon core is seated against drives. 3. Thread ribbon through and under mechanism. 4. Insert empty core and secure ribbon to core with tape. TDP43MY Quick Guide: PA26235A01_01 Page: 2 of 4 3-2010...
  • Page 3 Properly load the tape and ribbon into the TDP43MY printer. Lock down the printer cover. Press and hold Green button on the front of the Printer and Power the TDP43MY printer ON. Indicator light needs to flash three times, then release the Green Feed Button When printer starts feeding continuous tape, pop the top of the printer open, then press it back down securely locking it into place.
  • Page 4 TDP43MY Quick Guide PLEASE NOTE: Use component labels with an odd number of columns with the TDP43MY. The TDP43MY has a fixed sensor and it needs to be able to “see” an actual label or a notch/line to tell the printer when a label begins and ends.