Instantaneous Play (Hot Start) (Md 1, Md 2) - Denon DN-M2300R Operating Instructions Manual

4
3- 1,2- 2-
1 2
2

(4) Instantaneous play (Hot Start) (MD 1, MD 2)

• A maximum of 5 tracks can be preset and played
instantaneously.
This function is called instantaneous play (Hot Start).
NOTES:
• The hot start data is cleared if the editing or recording
operations are performed during the hot start mode.
• Seamless playback and programmed playback are not
possible during the hot start mode.
Hot Start Load
Data loading.
1
Set the cartridge and cue or pause at the track for hot
start playback.
5 TRACK LOAD.
Press the MD 1 or MD 2 button while pressing the LOAD
button.
• The data for five tracks starting from the track at which
the cue or pause mode is set is loaded into the hot start
RAM.
[1]Loading..
(Example: Track 4 is set to pause)
2-
1
Disc
4Tr 5Tr
Instantaneous
play
No.1 No.2
(Hot Start)
• When the data loading is completed, the CUE LED will
light and the unit will be set to instantaneous play (Hot
Start) standby.
NOTE:
When the stop operation is set during data loading and the
data loading number (from 1 to 5) is completed, data
loading of subsequent tracks is stopped.
1 TRACK LOAD.
While depressing the LOAD button, press the number
button (from 1 to 5) for which data is to be entered. During
data loading the CUE LED will flashes.
2-
2
• When data loading is completed, the CUE LED lights
steadily.
PROGRAM TRACK LOAD.
• Hot start data can also be loaded in the programmed
2-
play mode. The data is loaded in the programmed order.
3
The programmed play mode is canceled after the data
is loaded.
4
1,2- 3-
1 2 1
2- ,4 2
2
6Tr 7Tr 8Tr 9Tr
No.3 No.4 No.5
[3]Loading..
NOTES:
• The instantaneous play (Hot Start) mode will end with one
track.
• A press of a number button during the instantaneous play
(Hot Start) mode will cause the unit to switch to the track of
the pressed number and start playing.
• Cue detection is also performed at the time of instantaneous
play (Hot Start) loading.
Tracks with a setting level less than 10 seconds from the
beginning of the track are loaded from the beginning of the
track.
Even when the level of cue detection is changed after
loading, the pause position will not change until the initial
data is cleared.
Hot Start
Starting the play operation.
During instantaneous play (Hot Start) standby, press the
number button (from 1 to 5) that is to be played to start
the instantaneous play (Hot Start) operation.
2]POPS
The number of the button for the track at which
1
playback started is shown on the display.
• Press the PLAY/PAUSE button while the number of the
number button is shown on the display.
• The track number flashes when an EOM is detected
during playback (when the EOM is turned on with the
presetting).
• When play finishes, the unit returns to instataneous
play (Hot Start) standby.
Stopping the play operation.
A press the CUE button during the play operation causes
the play to stop and returns the unit to instantaneuos play
(Hot Start) standby.
2
Repeat play.
When the LOOP button is pressed, the repeat mode is set.
Press the number button of the track to be played (from 1
to 5) to repeatedly play that track.
3-
1
• Press the LOOP button while a track is being played to
repeatedly play that track.
• Press the LOOP another time to cancel the repeat play
mode.
Hot start OFF.
–
4
Press while pressing
play mode.
ENGLISH
Off
LOAD to cancel the hot start
19