THUNDER TIGER Agusta A 119 Koala Assembly Manual

Advertisement

MEMO
16
Assembly Manual
No.3843
Warranty
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase.
It does not cover any damage caused by use or modification. The warranty does not extend
beyond the product itself and is limited only to the original cost of the kit. By the act of building this
user-assembled kit, the user accepts all resulting in liability for damage caused by the final
product. If the buyer is not prepared to accept this liability, it can be returned new and unused to
the place of purchase for a refund.
Notice: Adult Supervision Required
This is not a toy. Assembly and flying of this product requires adult supervision.
Read through this book completely and become familiar with the assembly and flight of this A119.
Inspect all parts for completeness and damage.
service if you encounter any problems.
Specifications:
Fuselage Length (less rotor): 57-1/4"(1450mm)
Fuselage Width (less rotor): 13"(330mm)
Fuselage Height: 18-1/4"(465mm)
Full-Equipped Weight: 8.38 lbs (3800g)
Browse www.thundertiger.com for customer
1
JK6053

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Agusta A 119 Koala and is the answer not in the manual?

Questions and answers

Summary of Contents for THUNDER TIGER Agusta A 119 Koala

  • Page 1 MEMO Assembly Manual Specifications: Fuselage Length (less rotor): 57-1/4”(1450mm) Fuselage Width (less rotor): 13”(330mm) No.3843 Fuselage Height: 18-1/4”(465mm) Full-Equipped Weight: 8.38 lbs (3800g) Warranty This kit is guaranteed to be free from defects in material and workmanship at the date of purchase. It does not cover any damage caused by use or modification.
  • Page 2 PRE-ASSEMBLY NOTES RECOMMENDED TOOLS & MATERIALS Congratulations on the purchase of our finest scale heli fuselage to date. This famous A119 fits Thunder Tiger Raptor 50, Tools: the light fuselage comes factory pre-painted with all necessary hardware. It is very easy to assemble and only takes you...
  • Page 3: Parts Drawings

    PARTS DRAWINGS PARTS DRAWINGS PV6057 Fuselage PV6061 Decoration Set Top Fuselage(1) Foot Step Foot Step (1) Wiper Base (2) Wiper (2) Pitot Tube(1) H/F Antenna (1) Support (4) L/F Antenna(2) Cap(4) Wiper Retaining M2 Nut (2) 2x6mm Screw (2) Mount (2) Collar (17) Front Fuselage(1) Rear Fuselage(1)
  • Page 4: Table Of Contents

    PARTS CHECK LIST 1. Make sure the Raptor is tested and adjusted before 4. Epoxy all the windows and windshield to the front you install in the fuselage. Once done the testing and fuselage in place. adjusting your Raptor, remove the canopy, landing skid, tail fins, boom supports and tail rotor assembly.
  • Page 5: Mounting

    16. Drill 2mm (5/64”) holes for L/F antenn as at the position as photos shown. One hole will be at the cross molded line. Install the antenna and us e the 10. Secure the mechanism on the wood mount firmly. 7.Locate the scale fittings as shown includes wiper, 13.
  • Page 6: Brace

    19. Locate silicone tube then cut it in four pieces in 22.Attach the landing skid in place then secure with 28. Locate 3x10mm setscrews, apply a tiny epoxy on 25. Install the retainer and secure with three 3x8mm length of 10mm (3/8”) mounting strap with 3x18mm wood screws.
  • Page 7: Assembly

    42mm 31. Trim the tail fuselage as shown to make sure the tail 38. Cut the foot step in length of 50mm(1-7/8”). 36. Use the same way to install the top fuselage with 12 pitch control rod is work smoothly. Assemble the whole foot step as shown, note the pieces of 2x5mm wood screws.
  • Page 8 40. Refer to the box label and apply the decal. Above is Test Flight the bottom tail fuselage which you can see how to apply 1. When hovering the A119, try to keep rotor speed at the two golden strips. approximately 1600~1700 RPM.

Table of Contents