Mechanical Adjustments; Electrical Adjustments - Sony HCD-VX555J Service Manual

QQ

MECHANICAL ADJUSTMENTS

3 7 63 1515 0
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
erase head
capstan
2. Demagnetize the record/playback head with a head
demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
Torque Measurement
Mode
FWD
FWD
back tension
REV
REV
back tension
TE
L 13942296513
FF/REW
FWD tension
REV tension
www
.
http://www.xiaoyu163.com
SECTION 4
pinch rollers
rubber belts
idlers
Torque meter Meter reading
3.06 N • m to 6.96 N • m
31 to 71 g • cm
CQ-102C
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
CQ-102C 2 to 6 g • cm
(0.02 – 0.08 oz • inch)
3.06 N • m to 6.96 N • m
CQ-102RC 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m
CQ-102RC 2 to 6 g • cm
(0.02 – 0.08 oz • inch)
6.96 N • m to 14.02 N • m
CQ-201B 71 to 143 g • cm
(0.98 – 1.99 oz • inch)
9.80 N • m
CQ-403A 100 g or more
(3.53 oz or more)
9.80 N • m
CQ-403R 100 g or more
(3.53 oz or more)
x ao
y
i
http://www.xiaoyu163.com

ELECTRICAL ADJUSTMENTS

8
DECK SECTION
1. Demagnetize the record/playback head with a head
demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjust.
4. The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
6. The adjustments should be performed for both L-CH and R-
CH.
7. Switches and controls should be set as follows unless otherwise
specified.
• Test Tape
Tape
P-4-A100
WS-48B
P-4-L300J
Record/Playback Head Azimuth Adjustment
DECK A
Note: Perform this adjustments for both decks
Q Q
Procedure:
3 6 7 1 3
1. Mode: Playback
test tape
P-4-A100
(10 kHz, –10 dB)
u163
.
HCD-VX555/VX555J
SECTION 5
2 9 9 4 2 8
0 dB=0.775 V
Signal
10 kHz, –10 dB Azimuth Adjustment
3 kHz, 0 dB Tape Speed Adjustment
315 Hz, 0 dB Level Adjustment
DECK B
1 5 0 5 8 2 9 9 4
MAIN board
CN301
Pin 3 (L-CH)
Pin 1 (R-CH)
set
MAIN board
CN301
Pin 2 (GND)
m
co
9 9
Used for
2 8 9 9
level meter
+
–
15