Sound; Setup; Autoprogram - Emerson LF320EM4 A Owner's Manual

Sound

Before you begin:
You must set Home in Location. ➟ p.29
Otherwise, personalized Picture and Sound settings will not be
memorized after the unit goes into Standby mode.
1
Press MENU and use ▲▼ to select Sound, then press OK.
Picture Auto sound
Sound Equalizer

Setup

Virtual surround sound
Features Auto volume leveling
Language TV speakers
USB Digital output format
Primary MTS
2
Use ▲▼◄► to select the item you want to adjust, then press OK.
to select the desired setting, then press OK.
(Personal, Standard, Vivid, Sports, Movie, Music and News)
Auto sound
When you adjust the following settings (Equalizer,
Virtual surround sound and Auto volume leveling),
Personal sound will be set automatically.
Adjust the Tonal Quality for each frequency.
Cursor
Equalizer
to Adjust each level of Tonal Quality
Press BACK to go back to the Previous Menu.
Virtual Surround Sound gives you the Stereophonic virtual space through
your existing 2-channel Stereo System.
Off
Virtual surround
sound
On
This function keeps a Constant Loudness Level between the TV
Commercials and the Programs.
Off
Auto volume
leveling
On
You can select the Audio Output from the unit's speakers or not. If your
amplifier is HDMI link function compatible and connected by an HDMI
cable to this unit, some sound operations such as volume up can be
changed by using this unit's Remote Control.
On
Off
TV speakers
CEC Link
You can select Audio Output through a Digital Audio Output connector.
Multichannel
Digital output
format
PCM
Standard
On
Off
On
Multichannel
Stereo
▼ ▲
Cursor
Natural effect.
Emphasized effect.
to Remove the auto volume leveling
to Reduce Volume Differences between
the TV Commercials and the Programs
to Output Sound from the unit's
Speakers
no Output Sound from the unit's
Speakers
to control Audio Output from your
connected fun-Link (HDMI CEC)
Compliant Devices with VOL + / − by
using this unit's Remote Control.
to Output Multichannel Signals.
(When the Audio of the content is PCM,
it will be Output in PCM even if
Multichannel is selected.)
to Output PCM signals.
You can set the Output mode as a default for the Sound mode (Analog
TV only).
This setting is not interlocked when you change the Output mode by
pressing SAP. Refer to Switching Audio Mode. ➟ p.18
Stereo
Primary MTS Mono
SAP
Setup
Before you begin:
Make sure the unit is connected to Antenna or Cable.
1
Press MENU and use ▲▼ to select Setup, then press OK.
Picture

Autoprogram

Sound Channel list
Setup Add channels
Features Antenna
Language
USB
2
Adjust the following items.
Autoprogram
Be sure the RF cable is correctly connected to this unit and you are
registered with your cable TV provider when you install Cable channels.
1
Use ▲▼ to select Autoprogram, then press OK.
• If you run Autoprogram when you have Locked channels, a
message appears asking to enter your PIN. Enter your PIN in
order to complete the installation. You need to set the Channel
Lock again after the installation.
2
Use ▲▼ to select an appropriate option, then press OK.
– When Antenna is selected, the TV detects any off-the-air
antenna signals. It searches for ATSC (Digital) and NTSC
(Analog) channels available in your area.
– When Cable is selected, the TV detects signals supplied by
Cable. It searches for DTV, Analog TV and Cable channels
available in your area.
Picture
Autoprogram will rescan all channels.
Auto programming may take more than 20
Sound
minutes to complete.
Setup
Features
Select your signal source.
Language
Antenna
USB
Cable Cable
to Output Stereo Audio
to Output Mono Audio
to Output Second Audio Program
Back
Antenna
Cable
Or
ANTENNA IN
Continued on next page.
22
English