Connecting A Home Automation Device; Installation Check Sheet; Electric Wiring Diagram - Sanyo SAP-KMRV74EH Installation Instructions Manual

7. Connecting a Home Automation Device

The HA (white) 4P terminal is located on the indoor unit PCB. If a HA device will be used,
connect it to this terminal.
Also, refer to Section 9. Electric Wiring Diagram in the outdoor unit installation manual.

8. Installation Check Sheet

The strength of the installation location is sufficient to support the Air Conditioner weight.
The indoor and outdoor units are installed level and vertically.
The power and voltage are as specified.
Inter-unit cables are securely fastened to the terminal board.
Inter-unit cables are securely fixed.
The power cord and inter-unit cables are not connected anywhere along their paths.
The ground wire is securely connected.
An air purge of the refrigerant circuit has been conducted.
A leak test of the tubing connections has been performed.
Thermal insulation has been applied to the tubing connections.
Drain connections are secure and water drains properly.
Putty has been used to close the hole in the wall.
All service valves are fully open.
Remote controller signals are being positively received.

9. Electric Wiring Diagram

Diagrama de cableado eléctrico
Diagramme de câblage électrique
Elektrisches Schaltbild
Diagramma dei circuiti elettrici
Diagrama da fiação elétrica
¢ ¢ È È ¿ ¿ Á Á Ú Ú Ì Ì Ì Ì Ë Ë Ï Ï Â Â Î Î Ù Ù Ú Ú È È Î Î ‹ ‹ ˜ ˜ Î Î Ï Ï ˆ ˆ ‰ ‰ › › ˆ ˆ Û Û Ë Ë ˜ ˜
Indoor Unit
Unidad interior
Appareil intérieur
Innenraumgerät
Unità Interna
Unidade interior
∂ ∂ Û Û ˆ ˆ Ù Ù Â Â Ú Ú È È Î Î ‹ ‹ Ì Ì Ô Ô Ó Ó ¿ ¿ ‰ ‰
SAP-KMRV74/94/124EH
EVAPORATOR
CONNECTOR
RED
1 1 1
PNK
2 2 2
FLAP BLU
3 3 3
4 4 BRN 4
YEL
5 5 5
FLAP MOTOR
RED
1
2
BLK
3
FM
WHT 4
YEL
5
BLU
6
FAN MOTOR
24
TERMINAL BASE
BLK
1
WHT 2
RED 3
4
AC1 AC2 SI
RED
1 1 1 1
2 2 WHT 2 2
1
WHT
3 3 3 3
2
FLAP
WHT
4 4 4 4
3
5P(WHT) LAMP
WHT
5 5 5 5
4
10P( WHT )
6 6 WHT 6 6
5
WHT
7 7 7 7
WHT
8 8 8 8
WHT
9 9 9 9
10 10 WHT 10 10
CONTROLLER
ROOM THERMISTOR
1 1 BLK
1
BLK
2 2
ROOM/COIL
2
4P( WHT ) BLK
3 3
3 DCM
BLK
4 4
6P(BLU)
4
COIL THERMISTOR
5
6
1 1 WHT 1 1
ION
RED
2 2 2 2
3P( WHT )
3 3 BLK 3 3
CONNECTOR
HA
JEM-A
4P( WHT )
1 2 3 4
1 2 3 4
1 2 3 4
ION
ION ASSY
TERMINAL
8FA-2-5257-72600-1
Fig. 33a