Page 2: Table Of Contents
C O N T E N T S Ⅰ Ⅰ . SPECIFICATION 1. CAMERA SPECIFICATION……………………………………………………………………………………… 4 2. SYSTEM REQUIREMENTS …………………………………………………………………………………… 7 3. TFT LCD PANEL MARK ………………………………………………………………………………………… 8 4. CONNECTION DIAGRAM ……………………………………………………………………………………… 11 5. IDENTIFICATION OF FEATURES …………………………………………………………………………… 12 Ⅱ Ⅱ . . E E X X P P L L O O D D E E D D V V I I E E W W A A N N D D P P A A R R T T S S L L I I S S T T 1.
Page 3 Ⅴ Ⅴ . . C C I I R R C C U U I I T T D D I I A A G G R R A A M M 1. CIRCUIT DIAGRAM …………………………………………………………………………………………………… 106 1) MAIN_DSP ……………………………………………………………………………………………… 107 2) MAIN_MEMORY ……………………………………………………………………………………………………...
Page 4: Camera Specification
Ⅰ. SPECIFICATION 1. CAMERA SPECIFICATION Image Sensor - Type : 1/2.5″ CCD - Effective Pixel : Approx. 7.2 Mega Pixels - Total Pixel : Approx. 7.4 Mega Pixels Lens - Focal Length : f = 6.3 ~18.9mm (35mm equivalent : 38 ~114mm) : NV lens - F No.
Page 5 1456 1402 Normal 1793 1780 ※ These figures are measured under Samsung’s standard conditions and may vary depending on shooting conditions and camera settings. Image Play - Type : Single image, Thumbnail, Slide show (Effect, B.G.M), Album, Movie Interface - Digital output connector : USB 2.0...
Page 6 Ⅰ. SPECIFICATION ※ MP3 Specification Audio - Frequency : 20Hz ~ 20KHz - Earphone Port : 2.5mm Port (Stereo Type) - Output : Maximum Volume Left 40mW + Right 40mW (16Ω) - Noise Ratio : 88 dB with 20 KHz LPF File - File Format : MP3 (MPEG-1/2/2.5 Layer 3) - Bit Rate : 48 ~ 320kbps (Including VBR)
Page 7: System Requirements
Ⅰ. SPECIFICATION 2. System Requirements F F o o r r W W i i n n d d o o w w s s F F o o r r M M a a c c i i n n t t o o s s h h PC with processor better than Pentium II Power Mac G3 or later / Intel Processor 450MHz (Pentium 800MHz recommended)
Page 8 Ⅰ. SPECIFICATION 3. LCD monitor indicator ■ Recording mode ③ ② ① ⑫ ④ ⑬ ⑤ ⑭ ⑥ ⑦ ⑮ ⑯ ⑧ ⑨ ⑰ ⑱ ⑩ ⑪ ⑲ ⑳...
Page 9 Ⅰ. SPECIFICATION ① ⑫ : Optical / Digital Zoom bar / : Battery Digital Zoom rate ② 10 : Number of available shots remaining ⑬ : Image size 00:00:00 : Available recording time (Movie clip / Voice recording) ⑭ : Image quality / Frame rate ③...
Page 10 Ⅰ. SPECIFICATION ■ Play mode ④ ③ ② ① ⑤ ⑥ ⑬ ⑦ ⑫ F100 ⑪ 10/1 ⑩ FLASH ⑨ SIZE 3072x2304 ⑧ DATE 2007/02/01 Description Icon Battery 100-0010 Folder name & File name Memory card indicator Playback mode Voice Memo Protect DPOF 2007/02/01...
Page 11 Ⅰ. SPECIFICATION 4 4 . . C C O O N N N N E E C C T T I I O O N N D D I I A A G G R R A A M M SD Card Card Reader TV Monitor...
Page 12: Identification Of Features
Ⅰ. SPECIFICATION 5. IDENTIFICATION OF FEATURES Front & Top Power button Speaker Shutter button Face Recognition (FR) / Lock button Self-timer / AF lamp Flash Lens Microphone Back 이어폰 연결부 Zoom W (Thumbnail) / Zoom T (Digital zoom) / Volume button Camera status lamp LCD monitor Camera strap...
Page 13 Ⅰ. SPECIFICATION Side Battery chamber Memory card slot Battery chamber cover Battery lock lever Bottom Tripod socket USB / AV port...
Page 14: Main Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 1. MAIN ASSEMBLY 1-18 1-16 1-17 1-15 1-21 1-23 1-11 1-10 1-20 1-13 1-12 1-19 1-22 1-14...
Page 15 1-14 Q6003049101A SCREW 1-15 Q7011059202A LCD FRAME 1-16 Q0961900101A SCREW 1-17 Q9001122701A LCD ASSY Q9001122801A LCD UPPER ASSY VLUU i70 MASKING SILVER Q9001122801B LCD UPPER ASSY BLACK Q9001122801C LCD UPPER ASSY PINK 1-18 Q9001122801D LCD UPPER ASSY GOLD Q9001122801E LCD UPPER ASSY Samsung i70...
Page 16: Body Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 2. BODY ASSEMBLY 2-17 2-16 2-10 2-14 2-11 2-15 2-12...
Page 17 PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q9001122101A FRONT SLIDE COVER F ASSY VLUU i70 SILVER Q9001122101B FRONT SLIDE COVER F ASSY VLUU i70 BLACK Q9001122101C FRONT SLIDE COVER F ASSY VLUU i70 PINK Q9001122101D...
Page 18 Ⅱ. EXPLODED VIEW AND PART LIST ▶ ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q7217395601A AF LED WINDOW Q9001122201A BATTERY ASSY Q9001125501A MAIN FRAME ASSY Q7409272101A MAIN FRAME SUB TAPE Q7409271901A MIC FPCB TAPE Q6001021601A SCREW Q9001126301A...
Page 19 Ⅱ. EXPLODED VIEW AND PART LIST ▶ ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q7217396801A GUIDE RAIL U SILVER Q7217396801B GUIDE RAIL U BLACK 2-14 Q7217396801C GUIDE RAIL U PINK Q7217396801A GUIDE RAIL U GOLD Q7217396901A GUIDE RAIL B...
Page 20: Barrel Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 3. BARREL ASSEMBLY...
Page 21 Ⅱ. EXPLODED VIEW AND PART LIST ▶ ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q7212193402A LENS BASE Q9002149801A 5TH LENS BARREL ASSY Q9005163301A SHUTTER ASS'Y Q9002149601A 3RD LENS BARREL ASSY Q7411123303A GUIDE BAR B Q9002151101A 2ND CLIP ASSY Q9002149501A...
Page 22: Battery Cover Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 4. BATTERY COVER ASSEMBLY 4-21 4-20 4-17 4-18 4-16 4-19 4-14 4-15 4-13 4-22 4-23 4-12 4-11 4-10...
Page 23 Ⅱ. EXPLODED VIEW AND PART LIST ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q9008112901A SUB PCB ASSY Q9001122301A BATTERY CHAMBER ASSY Q7211087901A BATTERY CHAMBER Q6107068702A BATTERY PUSH SPRING Q8411000801A SLIDE SHAFT Q7003000501A BATTERY LOCK LEVER Q6107068301A BATTERY LOCK LEVER SPRING Q8411000701A...
Page 24: Top Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 5. TOP ASSEMBLY 5-10 5-11...
Page 25 Ⅱ. EXPLODED VIEW AND PART LIST ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q9007279701A TOP COVER ASSY SILVER Q9007279701B TOP COVER ASSY BLACK Q9007279701C TOP COVER ASSY PINK Q9007279701D TOP COVER ASSY GOLD Q7217396202A TOP COVER Q7217397001A POWER BUTTON...
Page 26: Front Cover Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 6. FRONT COVER ASSEMBLY 6-12 6-11...
Page 27 Q9007279701A TOP ASSY Q7409282401A FRONT SLIDE TAPE 6-10 Q7409284003A SLIDE COVER SHEET 6-11 Q7409284003A CONDENSOR TAPE A Q9007279601A FRONT COVER ASSY VLUU i70 MASKING SILVER Q9007279601B FRONT COVER ASSY BLACK Q9007279601C FRONT COVER ASSY PINK 6-12 Q9007279601D FRONT COVER ASSY...
Page 28: Back Cover Assembly
Ⅱ. EXPLODED VIEW AND PART LIST 7. BACK COVER ASSEMBLY 7-18 7-17 7-12 7-14 7-16 7-10 7-13 7-15 7-11...
Page 29 Ⅱ. EXPLODED VIEW AND PART LIST ▶ ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q7217399601A BACK COVER Q7409269601A 9KEY METAL DOME SHEET Q7409269501A ZOOM METAL DOME SHEET Q7217396101A FUCTION LAMP WINDOW Q9008115101A 9KEY FPCB ASSY Q9006017901A 9KEY ASSY Q9006018001A...
Page 30: Packing Item
Ⅱ. EXPLODED VIEW AND PART LIST 8. PACKING ITEM 8-14 8-11 8-10 8-19 8-12 8-13 8-15 8-16 8-17 8-18...
Page 31 Q4404000301A AC_ADAPTOR_4.2V (SAC-45)_EXP Q4404000401A AC_ADAPTOR_4.2V (SAC-45)_USA 8-10 Q4404000501A AC_ADAPTOR_4.2V (SAC-45)_UK Q4404000601A AC_ADAPTOR_4.2V (SAC-45)_AUS Q4404000701A AC_ADAPTOR_4.2V (SAC-45)_CHI_TSOE Q4404000801A AC_ADAPTOR_4.2V (SAC-45)_ARG 8-11 Q3009001301A Earphone_VLUU i70 8-12 Q3802006202A 24PIN USB Cable(Charger)_SUC-C2 8-13 Q3802006301A 24PIN AV CABLE_NV3 8-14 Q1107003201A Multi Media Card (1GB) Samsung...
Page 32 Ⅱ. EXPLODED VIEW AND PART LIST ▶ ▶ PARTS LIST Fig.No Parts No. Parts Name Q’ty Supply Available Parts Remarks Q6806369501A Q_GUIDE_VLUU_i70_KOR Q6806369801A Q_GUIDE_Samsung_i70_ENG Q6806369901A Q_GUIDE_Samsung_i70_GER Q6806370001A Q_GUIDE_Samsung_i70_FRA Q6806370101A Q_GUIDE_Samsung_i70_SPA Q6806370201A Q_GUIDE_Samsung_i70_ITA Q6806370301A Q_GUIDE_Samsung_i70_CHI_T Q6806370401A Q_GUIDE_Samsung_i70_DUT Q6806370501A Q_GUIDE_Samsung_i70_POR 8-17 8-15 Q6806370601A Q_GUIDE_Samsung_i70_SWE Q6806370701A...
Page 33 Q6807009502E CARD_PRODUCT(Mexico) Q6807012101A WARRANTY CARD_IRAN Q6807012401A WARRANTY CARD_TURKEY Q6807012501A SERVICE_CENTER_TURKEY Q7409266801A MIC LABEL_VLUU i70 (MADE IN KOREA) Q7409266701A MIC LABEL VLUU i70(MADE IN CHINA) 8-19 Q7409266901A FCC LABEL_Samsung i70(MADE IN KOREA) Q7409267001A FCC LABEL_Samsung i70(MADE IN CHINA) Q7409267101A FCC LABEL_Samsung i70(MADE BY SAMSUNG)
Page 34: Firmware
Ⅲ. ADJUSTMENT 1. FIRMWARE 1) Reseting Camera 1. Remove an External Memory Card from the camera. 2. Turn-On the camera using a Full-Charged Battery or the AC Adaptor. 3. While pressed the M + FD (Face Recognition) Button, Turn-Off the camera.
Page 35 Ⅲ. ADJUSTMENT 4. Turn on the camera and check whether the camera is reset or not.
Page 36 Ⅲ. ADJUSTMENT 2) Checking version 1. Remove an External Memory Card from the camera. 2. Turn-On the camera, then enter the Voice Recording Mode. 3. Press the 4 function button as following order. (Left → Right → Down → Fn button)
Page 37 Ⅲ. ADJUSTMENT 4. Shown the Running Firmware Version on the LCD.
Page 38 Ⅲ. ADJUSTMENT 3) Upgrading 1. Insert a memory card that has the Firmware File. ※ Be sure that make back-up the adjustment data, before upgraded the firmware. Otherwise, all adjustment data might be initialized. In addition, the firmware file name must be "i70_06_xx_xx_x.bin". 2.
Page 39 Ⅲ. ADJUSTMENT 3. Press the 4 function button as following order. (Left → Right → Down → Fn button) 5. "Firmware Upgrading... i70_07_03_25_6_PR' message will display for about 1 sec. And then the firmware will be upgraded during about 30sec 6.
Page 40 Ⅲ. ADJUSTMENT 2. ADJUSTMENT CAUTION 1) Basic Information of Adjustment After changing the electronic parts of i7, the parts have to be adjusted in accordance withe the adjusted items. The items listed on the table are have to be adjusted after changing. 1>...
Page 41 Ⅲ. ADJUSTMENT < Description of TXT file > Use the Memo pad of Basic Windows program and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 42 Ⅲ. ADJUSTMENT //adj_control progress_skip_sig //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 43 Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 44 Ⅲ. ADJUSTMENT mode playback set delay 10 power off end total (Recommend that act the Burning Test with the CCD DEFECT CELL adjustment) // Burn_In // start BURNING // burn repeat 15 adj_control check_process_id 65532 //3 ...
Page 45 Ⅲ. ADJUSTMENT set zoom 0 //19 set delay 10 //20 capture image //21 set delay 5 //22 // WIDE IMAGE Shot // set flash off //23 set img_size 5m_w //24 set delay 10 //25 capture image //26 set img_size 7m //27 set delay 5 //28 // ISO 1000 Shot // ...
Page 46 Ⅲ. ADJUSTMENT set self_timer off //49 set delay 10 //50 //delay: 5 --> 10 // Photo Frame Shot // capture photoframe_set //51 set delay 10 //52 capture image //53 set delay 10 //54 //delay: 5 --> 10 // division shot // capture composite //55 set delay 10 //56 ...
Page 47 Ⅲ. ADJUSTMENT playback right //83 set delay 5 //84 playback right //85 set delay 5 //86 playback right //87 set delay 5 //88 playback right //89 set delay 5 //90 playback right //91 set delay 5 //92 mode program //93 end BURNING start CCDdefect // image shot for inspeting high iso noise // ...
Page 48 Ⅲ. ADJUSTMENT adj_control save_log_file adj_control progress_sig_on mode program adj_defective_pixel ref_level1 3100 adj_defective_pixel white_defect_num 3000 adj_defective_pixel run set delay 30 power off end CCDdefect ※ SD Card, which will be used, have to be formatted on the PC.
Page 49 Ⅲ. ADJUSTMENT 2) OB SETTING After changing the MAIN PCB, adjust the black color. <How to adjust> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Adjustment will be done automatically.
Page 50 Ⅲ. ADJUSTMENT adj_ob run //adj_control progress_skip_sig //---------- Lens Shading ----------// adj_control progress_sig_on adj_control save_log_file mode program set img_size 7m set flash off set wb auto set metering spot set iso 100 adj_lens_shading set_ratio 60 adj_lens_shading run ...
Page 51 Ⅲ. ADJUSTMENT adj_sh_close init_hd 17 adj_sh_close limit 9 adj_sh_close run //adj_control progress_skip_sig set delay 30 // //---------- Flash ----------// adj_control progress_sig_on adj_control save_log_file mode program set flash fill_in adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185...
Page 52 Ⅲ. ADJUSTMENT adj_punt zoom 0 1 2 3 4 5 6 7 adj_punt focus_step_min 2 75 154 237 306 394 475 543 adj_punt focus_step_max 118 193 274 362 473 569 664 752 adj_punt focus_slope_min 48 63 66 73 76 70 57 adj_punt focus_slope_max 94 102 106 118 123 123 125 ...
Page 53 Ⅲ. ADJUSTMENT 3) LENS SHADING This menu adjust the brightness gaps between center of the lens and around the lens. Required Equipment : AE TESTER(LV: 8.2, 3300K) <How to adjust> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and attach the camera to the AE TESTER.
Page 54 Ⅲ. ADJUSTMENT <Description of TXT file> When modify the program, use the Memo Pad of Windows and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 55 Ⅲ. ADJUSTMENT //adj_control progress_skip_sig //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 56 Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 57 Ⅲ. ADJUSTMENT set delay 10 mode playback set delay 10 power off end total ※ SD Card, which will be used, have to be formatted on the PC.
Page 58: Adjustmnet
Ⅲ. ADJUSTMENT 4) B/T LEVEL ADJ After changing the MAIN PCB, adjust the Standard Voltage LEVEL. <How to adjust> a...Prepare the POWER SUPPLY. b...Connect the camera to the POWER SUPPLY. c...Set the voltage to 2.71V. d...Download the adjustment file and save it to SD memory card. e...Insert the SD memory card that has the program file and turn on the camera.
Page 59: Mode Program Set Img_Size 7M
Ⅲ. ADJUSTMENT mode program set img_size 7m set flash off set wb auto adj_ob set_range 100 4000 adj_ob run //adj_control progress_skip_sig //---------- Lens Shading ----------// adj_control progress_sig_on adj_control save_log_file mode program set img_size 7m set flash off set wb auto set metering spot...
Page 60 Ⅲ. ADJUSTMENT mode program set iso auto set metering multi adj_sh_close preview_lum 100 300 adj_sh_close init_count 15 adj_sh_close init_hd 17 adj_sh_close limit 9 adj_sh_close run //adj_control progress_skip_sig set delay 30 // //---------- Flash ----------// ...
Page 61 Ⅲ. ADJUSTMENT set delay 20 // //---------- PUNT ----------// adj_control set_process_id 65534 adj_control progress_sig_on adj_control save_log_file mode program adj_punt zoom 0 1 2 3 4 5 6 7 adj_punt focus_step_min 2 75 154 237 306 394 475 543 adj_punt focus_step_max 118 193 274 362 473 569 664 752 adj_punt focus_slope_min 48 63 66 73 76 70 57 adj_punt focus_slope_max 94 102 106 118 123 123 125...
Page 62 Ⅲ. ADJUSTMENT 5) SHUTTER CLOSE TIME ADJ Adjust the Close Timing of each camera's mechanical shutter. Required Equipment : AE TESTER(LV: 13, 3300K) <How to adjust> a...Prepare AE TESTER that can be test up to LV 13. b...Attach the camera to the AE TESTER. c...Set the LV to 13.
Page 63 Ⅲ. ADJUSTMENT <Description of TXT file> When modify the program, use the Memo Pad of Windows and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 64 Ⅲ. ADJUSTMENT //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 65: Mode Program Set Ev
Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 66: Set Delay 10
Ⅲ. ADJUSTMENT mode playback set delay 10 power off end total ※ SD Card, which will be used, have to be formatted on the PC.
Page 67 Ⅲ. ADJUSTMENT 6) CCD GAIN ADJ This adjustment is for minimizing the gabs of CCD saturation level of each camera. Required Equipment : AE TESTER(LV: 13, 3300K) <How to adjust> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and attach the camera to the AE TESTER.
Page 68 Ⅲ. ADJUSTMENT <Description of TXT file> When modify the program, use the Memo Pad of Windows and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 69 Ⅲ. ADJUSTMENT //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 70 Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 71: Set Zoom 7
Ⅲ. ADJUSTMENT set zoom 7 set delay 10 mode playback set delay 10 power off end total ※ SD Card, which will be used, have to be formatted on the PC.
Page 72 Ⅲ. ADJUSTMENT 7) FLASH ADJ <How to adjust> a...Arrange a 18% reflect chart in a darkroom. b...Arrange a camera in a darkroom. (Use TRIPOD) c...The distance between the reflect chart and the camera should be 80cm. d...Download the adjustment file and save it to SD memory card. e...Insert the SD memory card that has the program file and turn on the camera.
Page 73 Ⅲ. ADJUSTMENT <Description of TXT file> When modify the program, use the Memo Pad of Windows and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 74 Ⅲ. ADJUSTMENT //adj_control progress_skip_sig //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 75 Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 76 Ⅲ. ADJUSTMENT set delay 10 mode playback set delay 10 power off end total ※ SD Card, which will be used, have to be formatted on the PC.
Page 77 Ⅲ. ADJUSTMENT 8) FOCUS ADJ Adjust the Focus Range. < How to adjust > a...Arrange a chart for adjust the FOCUS. b...Attach the camera to the tripod. c...The distance between the chart and the camera should be 80cm. AF Chart d...Download the adjustment file and save it to SD memory card.
Page 78: Adj_Control Check_Process_Id 65535 // Adj_Control Progress_Sig_On
Ⅲ. ADJUSTMENT <Description of TXT file> When modify the program, use the Memo Pad of Windows and save it as "th73f_adj.txt". Use only section related to each adjustment. //---------- adjustmnet ----------// start total set reset //adj_control progress_sig_start //---------- OB ----------// ...
Page 79: Adj_Control Progress_Skip_Sig
Ⅲ. ADJUSTMENT //adj_control progress_skip_sig //---------- Battery Level ----------// adj_control progress_sig_on adj_control save_log_file mode playback adj_battery check 545 585 adj_battery level_set 520 544 555 575 532 //lock, empty,low,half,start adj_battery run //adj_control progress_skip_sig //---------- Shutter Close Time ----------// ...
Page 80 Ⅲ. ADJUSTMENT adj_flash trigger 300 800 2500 adj_flash min_limit 98 43 adj_flash mid_limit 363 117 adj_flash max_limit 805 185 adj_flash run //adj_control progress_skip_sig //---------- AWB_H ----------// adj_control progress_sig_on adj_control save_log_file mode program set ev 0 set wb auto adj_awb run 521 643 302 335 ...
Page 81 Ⅲ. ADJUSTMENT //---------- consumption current ----------// set delay 30 set zoom 0 set delay 10 set zoom 7 set delay 10 mode playback set delay 10 power off end total ※ SD Card, which will be used, have to be formatted on the PC.
Page 82 Ⅲ. ADJUSTMENT 9) BURNING TEST Check whether the camera operates correctly or not. a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Adjustment will be done automatically. ※...
Page 83 Ⅲ. ADJUSTMENT // TELE flash shot // set flash fill_in //14 set zoom 7 //15 set delay 10 //16 capture image //17 set delay 5 //18 // WIDE flash shot // set zoom 0 //19 set delay 10 //20 capture image //21 set delay 5 //22 ...
Page 84 Ⅲ. ADJUSTMENT set delay 5 //42 set shooting single //43 set delay 5 //44 // Self Timer shot // set self_timer 2sec //45 set delay 10 //46 capture image //47 set delay 30 //48 set self_timer off //49 set delay 10 //50 //delay: 5 --> 10 // Photo Frame shot // ...
Page 85 Ⅲ. ADJUSTMENT set delay 5 //72 playback right //73 set delay 5 //74 playback right //75 set delay 5 //76 playback right //77 set delay 5 //78 playback right //79 set delay 5 //80 playback right //81 set delay 5 //82 playback right //83 set delay 5 //84 playback right //85 set delay 5 //86 playback right //87 set delay 5 //88 playback right //89...
Page 86 Ⅲ. ADJUSTMENT capture image set delay 10 mount card set delay 20 set iso auto // CCD Defect adj // adj_control set_process_id 65528 adj_control save_log_file adj_control progress_sig_on mode program adj_defective_pixel ref_level1 3100 adj_defective_pixel white_defect_num 3000 adj_defective_pixel run ...
Page 87 Ⅲ. ADJUSTMENT 10) CCD DEFECT CELL After changing the MAIN PCB and CCD, adjust the defect of the CCD CELL. <How to adjust> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Adjustment will be done automatically.
Page 88 Ⅲ. ADJUSTMENT capture image //12 set delay 5 //13 // TELE flash shot // set flash fill_in //14 set zoom 7 //15 set delay 10 //16 capture image //17 set delay 5 //18 // WIDE flash shot // set zoom 0 //19 set delay 10 //20 capture image //21 set delay 5 //22 ...
Page 89 Ⅲ. ADJUSTMENT set shooting aeb //39 set delay 10 //40 capture image //41 set delay 5 //42 set shooting single //43 set delay 5 //44 // Self Timer shot // set self_timer 2sec //45 set delay 10 //46 capture image //47 set delay 30 //48 set self_timer off //49 set delay 10 //50 //delay: 5 -->...
Page 90 Ⅲ. ADJUSTMENT mode playback //69 set delay 5 //70 playback right //71 set delay 5 //72 playback right //73 set delay 5 //74 playback right //75 set delay 5 //76 playback right //77 set delay 5 //78 playback right //79 set delay 5 //80 playback right //81 set delay 5 //82 playback right //83 set delay 5 //84 ...
Page 91 Ⅲ. ADJUSTMENT set flash off set delay 10 capture image set delay 10 mount card set delay 20 set iso auto // CCD Defect adj // adj_control set_process_id 65528 adj_control save_log_file adj_control progress_sig_on mode program ...
Page 92 Ⅲ. ADJUSTMENT 11) EEPROM READ Make the adjustment data file by reading them in the camera. <How to Read> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Turn on the camera and the DATA in the EEPROM will be copied in the SD card.
Page 93 Ⅲ. ADJUSTMENT 12) EEPROM WRITE If you want to write the DATA of EEPROM, do as follows. <How to Write> a...Download the adjustment file and save it to SD memory card. b...Insert the SD memory card that has the program file and turn on the camera. c...Turn on the camera and the data of EEPROM will be copied to the camera.
Page 94: Main_Top
Ⅳ. PATTERN DIAGRAM 1. PARTS ARRANGEMENT FOR EACH PCB ASS’Y 1) MAIN_TOP...
Page 95: Main_Bottom
Ⅳ. PATTERN DIAGRAM 2) MAIN_BOTTOM...
Page 96: Card_Fpcb
Ⅳ. PATTERN DIAGRAM 3) CARD_FPCB...
Page 97: Ccd_Fpcb
Ⅳ. PATTERN DIAGRAM 4) CCD_FPCB...
Page 98: Sub_Fpcb_Top
Ⅳ. PATTERN DIAGRAM 5) SUB_FPCB_TOP...
Page 99: Sub_Fpcb_Bottom
Ⅳ. PATTERN DIAGRAM 6) SUB_FPCB_BOTTOM...
Page 100: Usb_Fpcb_Top
Ⅳ. PATTERN DIAGRAM 7) USB_FPCB_TOP...
Page 101: Usb_Fpcb_Bottom
Ⅳ. PATTERN DIAGRAM 8) USB_FPCB_BOTTOM...
Page 102: Strobo_Fpcb_Top
Ⅳ. PATTERN DIAGRAM 9) STROBO_FPCB_TOP...
Page 103: Strobo_Fpcb_Bottom
Ⅳ. PATTERN DIAGRAM 10) STROBO_FPCB_BOTTOM...
Page 104: Top_Fpcb
Ⅳ. PATTERN DIAGRAM 11) TOP_FPCB...
Page 105: Key_Fpcb
Ⅳ. PATTERN DIAGRAM 12) KEY_FPCB...
Page 106: Main_Dsp
Ⅴ. CIRCUIT DIAGRAM 1) MAIN_DSP...
Page 107: Main_Memory
Ⅴ. CIRCUIT DIAGRAM 2) MAIN_MEMORY...
Page 108: Main_Afe
Ⅴ. CIRCUIT DIAGRAM 3) MAIN_AFE...
Page 109: Main_Power
Ⅴ. CIRCUIT DIAGRAM 4) MAIN_POWER...
Page 110: Main_ Lcd
Ⅴ. CIRCUIT DIAGRAM 5) MAIN_ LCD...
Page 111: Main_Sub & Sd Card
Ⅴ. CIRCUIT DIAGRAM 6) MAIN_SUB & SD CARD...
Page 112: Main_Micom
Ⅴ. CIRCUIT DIAGRAM 7) MAIN_MICOM...
Page 113: Main_Otg
Ⅴ. CIRCUIT DIAGRAM 8) MAIN_OTG...
Page 114: Main_Audio
Ⅴ. CIRCUIT DIAGRAM 9) MAIN_AUDIO...
Page 115: Main_Usb_27Pin
Ⅴ. CIRCUIT DIAGRAM 10) MAIN_USB_27PIN...
Page 116: Main_Motor
Ⅴ. CIRCUIT DIAGRAM 11) MAIN_MOTOR...
Page 117: Top_Fpcb
Ⅴ. CIRCUIT DIAGRAM 12) TOP_FPCB...
Page 118: Sd Card_Fpcb
Ⅴ. CIRCUIT DIAGRAM 13) SD CARD_FPCB...
Page 119: Ccd_Fpcb
Ⅴ. CIRCUIT DIAGRAM 14) CCD_FPCB...
Page 120: Sub_Fpcb
Ⅴ. CIRCUIT DIAGRAM 15) SUB_FPCB...
Page 121: Usb_Fpcb
Ⅴ. CIRCUIT DIAGRAM 16) USB_FPCB...
Page 122: Key_Fpcb
Ⅴ. CIRCUIT DIAGRAM 17) KEY_FPCB...
Page 123: Mic_Fpcb
Ⅴ. CIRCUIT DIAGRAM 18) MIC_FPCB...
Page 124: Strobo_Fpcb
Ⅴ. CIRCUIT DIAGRAM 19) STROBO_FPCB...
Page 125: Service Information
Ⅵ. SERVICE INFORMATION 1. The order of disassembly and assembly ■ Caution 1. Do the disassembling and assembling camera where the blocking static electricity mat is on the table. 2. When handling the major PCBs of camera, please wearing the band which cuts off the electric current on the wrist.
Page 126 Ⅵ. SERVICE INFORMATION ■ ■ Disassembly 1. Remove 2 screws. 2. Remove 6 screws. 3. Remove 2 screws.
Page 127 Ⅵ. SERVICE INFORMATION 4. Disassemble the Side Cover.
Page 128 Ⅵ. SERVICE INFORMATION 5. Disassemble the Bottom Cover.
Page 129 Ⅵ. SERVICE INFORMATION 6. Remove 1 screw. 7. Disassemble the LCD Cover.
Page 130 Ⅵ. SERVICE INFORMATION 8. Disconnect the PCB from the connector. 9. Disassemble the LCD A'SSY.
Page 131 Ⅵ. SERVICE INFORMATION 10. Remove 2 screws. 11. Remove 1 screw.
Page 132 Ⅵ. SERVICE INFORMATION 12. Remove 1 screw. 13. Disassemble the below Cover.
Page 133 Ⅵ. SERVICE INFORMATION 14. Disconnect the PCB from the connector. 15. Disassemble the KEY pad A'SSY.
Page 134 Ⅵ. SERVICE INFORMATION 16. Remove 2 screws.
Page 135 Ⅵ. SERVICE INFORMATION 17. Disassemble the Slide Cover. 18. Disconnect 3 PCBs from each connector.
Page 136 Ⅵ. SERVICE INFORMATION 19. Remove 2 screws. 20. Disassemble the Main PCB & BARREL A'SSY.
Page 137 Ⅵ. SERVICE INFORMATION 21. Detach the below sticker. 22. Remove 3 screws.
Page 138 Ⅵ. SERVICE INFORMATION 23. Remove 1 screw. 24. Disassemble the Slide Plate.
Page 139 Ⅵ. SERVICE INFORMATION 25. Disassemble the Slide's Front Cover. 26. Disconnect the PCB from the connector.
Page 140 Ⅵ. SERVICE INFORMATION 27. Remove 2 screws. 28. Remove 2 screw.
Page 141 Ⅵ. SERVICE INFORMATION 29. Remove 4 screws. 30. Disassemble the Front Cover.
Page 142 Ⅵ. SERVICE INFORMATION 31. Detach the double-sticker.
Page 143 Ⅵ. SERVICE INFORMATION 32. Disassemble the Outer Connector A'SSY. 33. Disconnect the PCB from the connector.
Page 144 Ⅵ. SERVICE INFORMATION 34. Remove 1 screw. 35. Disassemble the FLASH PCB.
Page 145 Ⅵ. SERVICE INFORMATION 36. Finished...

Samsung i70 Service Manual

Table of Contents

Table of Contents

Table of Contents

Table of Contents

Quick Links

Chapters

Related Manuals for Samsung i70

Summary of Contents for Samsung i70

Table of Contents