Service Adjustment Data Table - Sanyo PLV-Z4000 Service Manual

Service Adjustment data table

No. Adjustment Item
Group: 0 Ad converter (PW392)
10 SOGTH
11 SOGHYSDIS
12 HS1TH
13 HS0TH
20 Anti-alias Filter
Anti-alias Down sample
21
(Read Only)
Anti-alias High Friquency
22
(Read Only)
Group: 20 Video decoder
10 XCXL Parameter
11 Sync Amp Low
12 Sync Amp High
13 Luma Setup Enable
14 Anti-Alias Filter
15 Anti-Alias Downsample
16 Anti-Alias High Frequency
17 CSC Adjust
20 R3DXL_TB_AMP for PAL
Group: 40 General
0 IP Mode
1 3:2 PullDown Mode
2 Detect Film Mode Enable
3 NR Enable for Analog YUV
4 NR Enable for Digital YUV
Group: 41 deinterlacer Setting
0 Motion Adaptive Weight Value
1 Angle Interpolation Level
2 CUE Low Pass Filter Enable
These initial values are the reference data written from the CPU
ROM to memory IC when replaced new memory IC. The adjustment
items indicated with "✻" are required to readjust following to the
"Electrical adjustments". Other items should be used with the initial
data value.
Initial Value
3/3/4
1/1/0
4
4
G1 - 4
G2 - 4
G3 - 6
G4 - 5
G5 - 4
G6 - 4
G7 - 4
G1 - 3
G2 - 3
G3 - 0
G4 - 1
G5 - 3
G6 - 3
G7 - 3
G1 - 1
G2 - 1
G3 - 3
G4 - 1
G5 - 3
G6 - 3
G7 - 3
2
0x0700
0x1000
0
2
1
1
0x400 / 0x400
3
1
1
0
1
0
Progressive Model 1, Film Parameter setting
30/30/30
4/4/4
0/0/0
- 53 -
range Input source / description
0 - 15 PC / Component / SCART SyncOn Green Threhould
0 - 1 PC / Component / SCART SyncOn Green Hsysterisis Enable
0 - 15 H Sync1 Threshold
0 - 15 H Sync0 Threshold
0 - 7
Setting Group
Group1 : PC (Read Only)
Group2 : Sxart (Read Only)
Group3 : YCbCr 480i, 575i
0 - 3 Group4 : YCbCr 480p, 575p
Group5 : YCbCr 720p 60, 720p 50
Group6 : YCbCr 1080i 60, 1080i 50
Group6 : YCbCr 1080p 60, 1080p 50
0 - 3
0 - 4 XCXL Leve
0 - 9999 Minimum sync amplitude threshold for HLOCK 1 to 0 transition
0 - 9999 Minimum sync amplitude threshold for HLOCK 0 to 1 transition
0 - 1 7.5IRE Mode (NTSC)
0 - 7 Anti-Alias Filter
0 - 3 Anti-Alias Downsample
0 - 3 Anti-Alias High Frequency
0x300 - 0x500 Composite / S-Video - CSC Adjust
0 - 3 R3DXL_TB_AMP for PAL
0 - 1 Setting of IP Off 0: IP Block non used 1: IP Block used IP=0
1 - 3 bit0 : Global Motion
"0 : 2:3pull down & 2:2pull down
0 - 2
2 : 2:2pull down"
0 - 1 0: Y & UV Detect Noise reduction 1: Y Detect TUV Noise reduction
Analog YUV : PC/Video/S-Video/Component Digital YUV : HDMI
0 - 1
<NSYUVEN>
0 - 255 <KDEINT>
0 - 5 0 : Conservative <====> 5 : Aggressive
0 - 1 <CUELPFEN>
Electrical Adjustments
bit1 : Video Motion
1 : 2:3pull down
Deinter Setting
-- Group
Group1 :
Composite /
S-Video
Group2 :
Component /
Scart / PC
Group3 : HDMI