Related Manuals for Foto Walser WalimexPro
Summary of Contents for Foto Walser WalimexPro
- Page 1 Copy of Instruction Manual LED Spotlight + Barndoors Gewerbering 26 86666 Burgheim Tel. +49/84 32 / 9489-0 Fax: +49/84 32 / 9489 - 8333 eMail: info@foto-walser.de www.foto-walser.de...
-
Page 2: Table Of Contents
Content How to understand the instruction manual ............ 4 Markings on the device ..................4 Markings in this manual ..................4 Important safety notes .................. 4 Unpack and check the device ................. 6 Overview about the parts ................7 Quick-start guide ................... 7 Preparation for operation ................ - Page 3 Thank you very much for your confidence. We wish you much pleasure and success with your new device. The LED Spotlight + Barndoors is equipped with long-living, energy-saving LED. The Light is especially developed for ambitious beginners and professional users in film and studio photography. It is characterized through its longevity, stable colour temperature and constant luminance (without flickering).
-
Page 4: How To Understand The Instruction Manual
How to understand the instruction manual Markings on the device This marking means, that your device meets the safety requirements of all relevant European Directives. This marking means, that your device should be disposed in the local disposal points. Markings in this manual Marking Meaning Indicates the handling and consequences of safety... - Page 5 WARNING Danger of electric shock, fire through short-circuit A short-circuit could be caused through defect cables and through humidity or moisture. A short- circuit can warm up the conductors, so that there isolation will melt or even melt thoroughly. This could lead to fire.
-
Page 6: Unpack And Check The Device
− Don´t touch the lamps with bare hands. Just touch the lamp at the plastic socket or wear clean cotton gloves or use a clean cloth. − Avoid touching the flash tube accidentally when mounting or changing accessories. Unpack and check the device •... -
Page 7: Overview About The Parts
Overview about the parts Housing 2. Dimmer 3. Fuse Holder 4. Lamp Socket with Locking Screw 5. Locking Screw Tilt Angle 6. Connection for Power Cord from Power Supply Unit 7. On/Off Switch 8. Handle 9. Barndoors 10. LED Quick-start guide ADVICE: The detailed instruction for the following operations can be found in the respective chapters in this instruction manual. -
Page 8: Mount Barndoors
• Loose locking screw. • Mount the device with the holder on the tripod. • Tighten locking screw. Holder with Fastening Screw Guide Rail Mount barndoors • Loose fastening screw. • Slide the barndoors into the lateral guide rail. • Tighten fastening screw. -
Page 9: Solve Problems
• Clean the device if necessary. See Cleaning. • Put the device and all demounted elements in one carton and carry and store them according to the requirements in the technical specifications. See Technical specifications. Solve problems Problem Possible reason Remedy Plug in the power cord correctly Device is switched on,... -
Page 10: Change Lamps
10.3 Change lamps WARNING Please just use suitable LED for this device. These LED´s should just be changed through an electrician. It is essential to send back the device to Foto Walser within the warranty time. 10.4 Change micro-fuse WARNING Danger of electric shock and fire through short-circuit A micro-fuse, which is not conform with the required specifications, doesn´t protect against the... -
Page 11: Technical Specifications
13. Technical specifications Device Micro-fuse Power Supply AC 220 - 230 V / 50 Hz (Power Supply Unit – Voltage 12V 5A Output) Weight approx.1,9 kg Vertical Pivoting Radius 180 ° Dimensions (LxWxT) approx. 18 cm x 18cm x 20 cm Protection Class IP 20 Output at 2m distance...