Using Multi Operations; Using System Off; Controlling Components - Pioneer SC-LX73 Operating Instructions Manual

Controlling the rest of your system (In case of SC-LX83)
• You don't need to program the receiver to switch on
or off. This is done automatically.
With Pioneer components, you don't need to:
• program the power to switch off in a shutdown
sequence (except DVD recorders);
These take priority in multi operations (not shutdown).
8 Repeat steps 5 to 7 to program a sequence of
commands.
When you're finished, use / to select 'EDIT
9
EXIT' from the menu and press ENTER.
You will return to the remote control Setup menu. Select
EXIT SETUP to exit.

Using multi operations

You can start multi operations with the receiver switched
on, or in standby.
MAIN
RECEIVER
ZONE2
BD DVD
TV CD
USB
iPod TUNER
MULTI CH
1 Press MULTI OPERATION.
MULTI OPERATE flashes in the display.
2 Press an input function button that has been set up
with a multi operation.
The receiver switches on (if it was in standby) and the
programmed multi operation is performed automatically.

Using System off

MAIN
RECEIVER
ZONE2
BD DVD
TV CD
USB
iPod TUNER
MULTI CH
1 Press MULTI OPERATION.
MULTI OPERATE flashes in the display.
Press  SOURCE.
2
The command sequence you programmed will run, then
all Pioneer components will switch off
3
receiver.
Note
1 With this remote control, the IR and RF modes can be selected separately for the individual input functions. To perform a multi operation on
a device (input function) for which the IR mode is selected, point the remote control toward the remote sensor on that device.
2 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
3 • With this remote control, the IR and RF modes can be selected separately for the individual input functions. To turn off the power of a device
(input function) for which the IR mode is selected using the System Off function, point the remote control toward the remote sensor on that device.
• When the power code of another brand is registered, the power on/off operation may be inverted. When using the System Off function for a
multi operation including the power codes of other brands, always check that the power of all the components has turned off.
SOURCE
3
MULTI MULTI
OPERATION OPERATION
BDR
DVR HDMI
NET RADIO
HMG ADAPTER
OPTION
1 2
SOURCE
3
MULTI MULTI
OPERATION OPERATION
BDR
DVR HDMI
NET RADIO
HMG
ADAPTER
OPTION
1 2
2
, followed by this

Controlling components

This remote control can control components after
entering the proper codes (see Selecting preset codes
directly on page 79). Set the remote control operation
selector switch to SOURCE, then press the input function
buttons to select the component.
• TV CONTROL on the remote control are dedicated to
control the TV assigned to the TV operation selector
switch. If you have two TVs, assign the main TV to the
TV operation selector switch.
RECEIVER
BD
TV
USB
iPod
PHONO
AUX
CH
INPUT
AUDIO
PARAMETER
1
TOP MENU
BAND
PRESET
CATEGORY
iPod CTRL
STATUS
THX
AUTO/ALC/
DIRECT
PGM
SIGNAL SEL SLEEP
D.ACCESS
MAIN
SOURCE
ZONE2 3
MULTI
OPERATION
BDR
DVD DVR HDMI
NET RADIO
CD HMG ADAPTER
OPTION
TUNER 1 2
MULTI CH
IN VIDEO CD-R
INPUT SELECT LIGHT
SOURCE
TV RECEIVER
VOL
VOL
TV CONTROL
MUTE MUTE
VIDEO
PARAMETER
TUNE
TOOLS
LIST
T.EDIT
GUIDE GUIDE
ENTER PRESET
RETURN
HOME
MENU
TUNE
PTY SEARCH
PHASE CTRL CH LEVEL
MPX PQLS MEMORY
STANDARD ADV SURR
STEREO
MENU
DIMMER AUDIO
A.ATT SBch MCACC INFO
DISP
HDMI OUT
CH
CLASS
ENTER
CLR
10
83
En