Page 1 LFD DISPLAY User Manual ME32C ME40C ME46C ME55C The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. BN46-00359B-01...
Page 2: Table Of Contents
Checking the Contents MDC Program Installation/Uninstallation Before Connecting Removing the Packaging Installation Pre-connection Checkpoints (for ME32C ME40C and ME46C models only) Uninstallation Removing the Packaging Connecting to a PC (for ME55C models only) What is MDC? Connection using the D-SUB cable (Analog type) 45...
Page 3 Table of contents Network System Setup Color Space Tool Settings White Balance Other Functions 10p White Balance Network Settings Group Management Gamma Connecting to a Wired Network Schedule Management Expert Pattern Wired Network Settings Troubleshooting Guide Motion Lighting Connecting to a Wireless Network Wireless Network Setting Picture Options Manual Network Setup...
Page 4 Max. Power Saving Eco Sensor Game Mode Software Update No Signal Power Off BD Wise By USB Auto Power Off Menu Transparency Contact Samsung Sound Feedback Security Auto Power Contents Home Safety Lock Standby Control MagicInfo Lite Button Lock Lamp Schedule...
Page 5 Table of contents MagicInfo Premium S Troubleshooting Guide Playing a Video Photos File Formats Compatible with MagicInfo Requirements Before Contacting Samsung Viewing a Photo (or Slide Show) Premium S Player Customer Service Center Read before using Testing the Product Music...
Page 6 Table of contents Appendix Contact SAMSUNG WORLD WIDE Responsibility for the Pay Service (Cost to Customers) Not a product defect A Product damage caused by customer's fault 239 Others Optimum Picture Quality and Afterimage Burn-in Prevention Optimum Picture Quality Prevention of Afterimage Burn-in...
Page 7: Before Using The Product
© 2013 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Page 8: Safety Precautions
Safety Precautions Cleaning ― Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. ― Take the following steps when cleaning. Caution ― The following images are for reference only. Real-life situations may differ from what is shown in the images.
Page 9: Storage
Storage Connect the power plug to a grounded power socket (type 1 insulated devices only). Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecolored • An electric shock or injury may result. stains on the product. ―...
Page 10: Installation
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. • A fire may result. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. • A fire or electric shock may result.
Page 11 SAMSUNG • Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
Page 12: Operation
If the product is dropped or the outer case is damaged, turn off the power Do not lift or move the product by pulling the power cord or any cable. switch and disconnect the power cord. Then contact Samsung Customer Service Center.
Page 13 • Your eyesight may deteriorate. when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center. • Product failure, an electric shock or fire may result. Do not hold the product upside-down or move it by holding the stand.
Page 14 Rest your eyes for more than 5 minutes for every 1 hour of product use. Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that •...
Page 15: Preparations
Checking the Contents Remove the styrofoam from the product. Removing the Packaging (for ME32C ME40C and ME46C models only) ― The following images are for reference only. Real-life situations may differ from what is shown in the images. Remove the black locking device at the bottom of the box.
Page 16: Removing The Packaging (For Me55C Models Only)
Removing the Packaging (for ME55C models only) Using the grooves in the box, lift and remove the top of the box. ― The following images are for reference only. Real-life situations may differ from what is shown in the images. Remove the black locking device at the bottom of the box.
Page 17: Checking The Components
Checking the Components Components - Contact the vendor where you ― Components may differ in different locations. purchased the product if any components are missing. - The appearance of the components and items sold separately may differ from the image shown. - A stand is not provided with the product.
Page 18: Items Sold Separately
Items sold separately - The following items can be purchased at your nearest retailer. Wall-mount Kit Stand RS232C-Stereo cable (P.57) DVI cable (P.45) HDMI-DVI cable (P.46) DP cable (P.47) HDMI cable (P.46) Stereo cable (P.26) RCA stereo cable (P.50) External sensor Kit (P.26) - The RS232C adapter can be used to connect to another monitor using the D-SUB (9-pin) type RS232C cable.
Page 19: Parts
Parts ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Panel Key Control Panel Buttons Description Power on the product. If you press the button when the product is turned on, the control menu will be displayed.
Page 20 ― If you press the Buttons Description button on the panel key (P.19) when the product is turned on, the control menu will be displayed. Select the connected input source. Control menu Move the panel key right to select Source in the control menu.
Page 21: Reverse Side
Port Description Reverse Side RS232C IN Connects to MDC using an RS232C-stereo adapter. ― The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. RS232C OUT IR / AMBIENT SENSOR IN Supplies power to the external sensor board or receives the light sensor signal.
Page 22: Anti-Theft Lock
Anti-theft Lock ― An anti-theft lock allows you to use the product securely even in public places. ― The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. ―...
Page 23: Remote Control
Remote Control ― Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. ― A button without a description in the image below is not supported on the product. Power on the product.
Page 24 TOOLS INFO Quickly select frequently used functions. Display information about the current input source. Move to the upper, lower, left or right menu, or adjust an option's setting. Confirm a menu selection. RETURN EXIT Return to the previous menu. Exit the current menu. Manually select a connected input source from HDMI PC, DVI, HDMI, or DisplayPort.
Page 25 Adjusting the OSD with the Remote Control Remote Control Reception Range Buttons Description Open the OSD menu. Select from Picture, Sound, Network, System Support in the displayed OSD menu screen. Change settings as desired. Use the remote control within 7m to 10m from the sensor on the product at an angle of 30 from the left and right.
Page 26: Connection Using An Ir Stereo Cable (Sold Separately)
Connection Using an IR Stereo Cable (sold separately) Turn off the device before connecting the External Sensor Kit. After it is connected, POWER POWER turn on the device. Controlling more than one display product using IR OUT IR/AMBIENT your remote control SENSOR IN •...
Page 27: Before Installing The Product (Installation Guide)
Tilting Angle and Rotation 15 ˚ ― Contact Samsung Customer Service Center for further details. • The product can be tilted at a maximum angle of 15 from a perpendicular wall surface. • To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Page 28: Dimensions
Figure 1.3 Side view Installation on an Indented Wall ― Contact Samsung Customer Service Center for further details. Plane view Minimum 40 mm Minimum 70 mm Minimum 50 mm Minimum 50 mm Ambient temperature: Under 35 C ― When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C.
Page 29: Installing The Wall Mount
We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
Page 30: Wall Mount Kit Specifications (Vesa)
Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
Page 31: Remote Control (Rs232C)
Remote Control (RS232C) • Pin assignment 1 2 3 4 5 Cable Connection RS232C Cable Interface RS232C (9 pins) 6 7 8 9 TxD (No.2), RxD (No.3), GND (No.5) Signal Bit rate 9600 bps Detect data carrier Data bits 8 bit Received data Parity None...
Page 32: Lan Cable
LAN Cable • RS232C cable Connector: 9-Pin D-Sub to Stereo Cable • Pin assignment 1 2 3 4 5 6 7 8 -P2- -P1- -P1- -P1- -P2- -P2- Female --------> STEREO <-------- PLUG Pin No Standard Color Signal ---------- (3.5ø) White and orange Orange White and green...
Page 33 Cross LAN cable (PC to PC) • Connector : RJ45 Direct LAN cable (PC to HUB) RJ45 RJ45 RJ45 MDC Signal Signal <--------> <--------> Signal Signal <--------> <--------> <--------> <--------> <--------> <-------->...
Page 34: Connection
Connection • Connection 2 • Connection 1 RJ45 RJ45 RS232C RS232C RS232C RS232C • Connection 3 RJ45 RS232C RS232C RS232C RS232C...
Page 35: Control Codes
Command type Command Value range Control Codes Video Wall On 0x84 Viewing control state (Get control command) Video Wall User Control 0x89 Header Command Data length Checksum • All communications take place in hexadecimals. The checksum is calculated by adding up all 0xAA Command type values except the header.
Page 36: Power Control
Power control Volume control • Function • Function A product can be powered on and off using a PC. The volume of a product can be adjusted using a PC. • Viewing power state (Get Power ON / OFF Status) •...
Page 37 Input source control 0x25 DisplayPort • Function ― DVI_video, HDMI1_PC and HDMI2_PC cannot be used with the Set command. They only respond to The input source of a product can be changed using a PC. "Get" commands. • Viewing input source state (Get Input Source Status) ―...
Page 38 Screen mode control • Nak Header Command Data length Ack/Nak r-CMD Val1 Checksum • Function The screen mode of a product can be changed using a PC. 0xAA 0xFF 0x18 "ERR" Screen mode cannot be controlled when the Video Wall function is enabled.
Page 39 PIP On/Off control Auto adjustment control (PC and BNC only) • Function • Function The PIP mode of a product can be turned on or off using a PC. Automatically adjust the PC system screen using a PC. ― Only available on models that have the PIP function. •...
Page 40 Video Wall Mode Control Safety Lock • Function • Function Video Wall mode can be activated on a product using a PC. PC can be used to turn the Safety Lock function on or off on a product. Video Wall This control is only available on a product whose is enabled.
Page 41 Video Wall On • Nak Header Command Data length Ack/Nak r-CMD Val1 Checksum • Function Turn Video Wall on or off on the product from your computer. 0xAA 0xFF 0x84 • Get Video Wall On/Off Status "ERR": A code showing what error has occurred Header Command Data length...
Page 42 10x10 Video Wall Model 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x1F 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x2F 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28...
Page 43 Wall_SNo: Product Number code assigned to the product 10x10 Video Wall Model : ( 1 ~ 100) Set Number Data 0x01 0x02 0x63 0x64 • Ack Header Command Data length Ack/Nak r-CMD Val1 Val2 Checksum 0xAA 0xFF 0x89 Wall_Div Wall_SNo •...
Page 44: Connecting And Using A Source Device
Chapter 03 Connecting and Using a Source Device Before Connecting Check the following before you connect this product with other devices. Devices that can be connected to this product Pre-connection Checkpoints include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players. ―...
Page 45: Connecting To A Pc
Connecting to a PC • Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. • A PC can be connected to the product in a variety of ways. Select a connection method suitable for your PC.
Page 46: Connection Using An Hdmi-Dvi Cable
Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable ― When you connect a PC to the product using an HDMI-DVI cable, set Edit Name DVI PC to access video and audio content stored on the PC. POWER POWER HDMI IN 1, HDMI IN 2 HDMI IN 1, HDMI IN 2 RGB / DVI / HDMI AUDIO IN...
Page 47: Connection Using An Dp Cable
Connection Using an DP Cable POWER DP IN • Precautions for using DP ― To increase the standby power capacity, the product stops DP communication when it is turned off or in power-saving mode. If the product in dual monitor mode is turned off or goes into power-saving mode, monitor setting changes may not be updated.
Page 48: Changing The Resolution
Changing the Resolution ― Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. ― The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel Display Settings, and change the resolution.
Page 49: Changing The Resolution On Windows 7
Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution, and change the resolution. Changing the Resolution on Windows 8 Go to Settings Control Panel Display Screen Resolution, and change the resolution.
Page 50: Connecting To A Video Device
Connecting to a Video Device Connection Using an HDMI Cable • Do not connect the power cable before connecting all other cables. Using an HDMI cable or HDMI to DVI Cable (up to 1080p) Ensure you connect a source device first before connecting the power cable. •...
Page 51: Connecting To An Audio System
Connecting to an Audio System Connecting an External Monitor ― Connecting parts may differ in different products. ― Connecting parts may differ in different products. POWER POWER DP OUT AUDIO OUT DP IN...
Page 52: Connecting The Network Box (Sold Separately)
Connecting the network box (Sold separately) ― For details on how to connect to a network box, refer to the user's manual provided with the network box upon purchase. MagicInfo To use MagicInfo, a network box (sold separately) must be connected to the product. ―...
Page 53 Select a display mode. Enter the IP information. MagicInfo Setup Wizard - v.1.12 MagicInfo Setup Wizard - v.1.12 Select Screen Type - step 4 Select TCP/IP - step 2 Obtain an IP address automatically Landscape Use the following IP address: IP address: 192 .
Page 54: Changing The Input Source
Changing the Input source Source allows you to select a variety of sources and change source device names. You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source.
Page 55: Using Mdc
Chapter 04 Using MDC Configuring Settings for Multi Control DisplayPort Daisy Chain • To display the DP IN video input through the DP OUT output port, select a device connection method from Single Stream Transport (SST) and Multi Stream Transport (MST). Clone: In this Single Stream Transport (SST) output mode, the same screen output is displayed on MENUm→...
Page 56: Mdc Program Installation/Uninstallation
MDC Program Installation/Uninstallation Installation MDC installation can be affected by the Insert the installation CD into the CD-ROM drive. graphics card, mother board and network conditions. Click the MDC Unified installation program. Select a language for installation. Next, click "OK". If a software installation window is not displayed on the main screen, install with When the...
Page 57: What Is Mdc
What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices Connecting to MDC simultaneously using a PC. Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor. POWER Monitor 1 RS232C IN...
Page 58: Using Mdc Via Ethernet
Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable. Connection using a direct LAN cable ― Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB. POWER Monitor 1 RJ45...
Page 59 Connection using a cross LAN cable ― Multiple products can be connected using the RS232C IN / OUT port on the product. POWER Monitor 1 RJ45 RS232C OUT Monitor 2 Computer...
Page 60: Connection Management
Connection Management Connection management includes the Connection list and Connection list modification options. Connection list - Connection list shows the details of the connections such as connection setting (IP/COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
Page 61: User Login
User Login Launching the programme displays the user login window. The initial login ID (Username: admin) and password (Password: admin) are set to admin. ― After logging in for the first time, make sure to change the password to ensure security. ―...
Page 62: Auto Set Id
Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0. ―...
Page 63: Cloning
Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window. ― To delete the settings you have configured, click the Paste Settings button.
Page 64: Command Retry
Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10.
Page 65: Getting Started With Mdc
Getting Started with MDC To start the program, click Start Programs Samsung MDC Unified. The login window appears after the MDC program is launched. Enter the user ID and password. • The default user ID and password are admin. • Make sure to change the password after the first login.
Page 66: Main Screen Layout
Main Screen Layout Change the status of a display device or the properties of the program. Menu Bar View a list of connected display devices or device groups. Device Category View a list of schedules for display devices. Schedule Category Select the display device you want to adjust.
Page 67 ― The volume can be changed or the sound can be muted only for displays that are turned on. Volume Volume • Adjust the volume of a selected display. • The volume can be adjusted using the slider bar in the range of 0 to 100. Mute •...
Page 68: Screen Adjustment
User Login User Settings • Add, delete or edit login information. Logout • Log out from the current user account as follows. • Click Logout. The message "Do you want to log admin out?" is displayed • Click Yes. The user login window appears. •...
Page 69 Color Color • Adjust the colors for the selected display device. Tint (G/R) • Adjust the tint for the selected display device. Color Tone • Adjust the background color tone for the selected display device. Color Temp. • Adjust the color temperature for the selected display device. ―...
Page 70 MPEG Noise Filter MPEG Noise Filter Reduces MPEG noise to provide improved picture quality. Medium High Auto • Smart LED Controls the LED backlight to maximize picture clarity. Cinema Black In Movie mode, this feature dims the top and bottom areas of the video image to provide a more immersive viewing experience.
Page 71: Advanced Features
Advanced features 3D Mode Select the 3D input format. 3D L/R Change Swap the left and right pictures. Displays the image for the left eye only. 3D Auto View 3D Auto View Message Notice, a pop up message window appears when the product receives a 3D signal. If you set 3D Control 3D Optimization...
Page 72: Advanced Settings
Advanced Settings Dynamic Contrast Adjust the screen contrast. Gamma Control Adjust the primary color intensity. RGB Only Mode Displays the Red, Green Blue color for making fine adjustments to the hue and saturation. Flesh Tone Emphasize pink “Flesh Tone. ” Motion Lighting Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
Page 73: Sound Adjustment
Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. Bass • Adjust the bass for the selected display. Treble • Adjust the treble for the selected display. Balance(L/R) - The Bass Treble...
Page 74 Format • Select the number of horizontal display devices. • Select the format to display the split screen. • A maximum of 15 displays can be arranged in a row. ― A maximum of 6 can be assigned to if 15 is assigned to H. •...
Page 75 General User Auto Color • Automatically adjust the screen colors. ― Available only in mode. Auto Power • Set the product to automatically power on. Standby Control • Set the standby mode to activate if an input source is not detected. Fan &...
Page 76 Security Safety Lock • Lock the on-screen menus. ― To unlock the menus, set Safety Lock to Off. Button Lock • Lock the buttons on the display device. ― To unlock the buttons, set Button Lock to Off. OSD Display Source OSD •...
Page 77 Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer On Timer • Repeat: Specify the period for which you want to repeat the selected Timer. Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, Manual Holiday...
Page 78: Screen Burn Protection
Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date. ― The Holiday Management function can be enabled or disabled in the Timer settings menu. •...
Page 79 Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. Timer: You can set the timer for Screen Saver. • • Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals (Period).
Page 80 Safety Screen Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time.
Page 81 Ticker Input text while a video or image is displayed and display the text on the screen. Ticker Enable or disable Ticker. • Message Enter a message to display on the screen. Timer Start Time End Time Set the to display a message (Message). Position Horizontal and Vertical.
Page 82: Tool Settings
Tool Settings Panel Control: Turn on or off the screen of a display device. • Remote Control: Enable or disable the remote control. • Virtual Romete Control: Control a device from a PC using the virtual remote control. • Security Reset Reset Picture: Reset the screen settings.
Page 83 Edit Column Configure the settings for the items that will be displayed on the list of displays. • Language: Select a language to use in the MDC program. After selecting a language, restart the MDC program to use the selected language. Options Command Retry Count: Specify the number of retry attempts when a command fails.
Page 84 Monitor Window A window appears showing details for data transfer between the computer and display devices. Filter • Information View the program information.
Page 85: Other Functions
Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
Page 86: Group Management
Group Management Create groups and manage the list of sets on a group basis. ― Duplicate group names cannot be used. Group Edit Creating Groups Right-click and select in the display device list section on the left side of the program window. In the Edit Group window displayed, click...
Page 87 Add on the sub level: Create a sub-group under the selected group. • Enter the group name. Deleting Groups Select a group name, and click Edit. In the Edit Group window displayed, click Delete. Click Yes. The group will be deleted.
Page 88: Schedule Management
Renaming Groups Select a group name, and click Edit. Edit Group window displayed, click Rename. In the If a cursor appears in the old group name, enter a new group name. Rename Schedule Management Creating Schedules Create and register a schedule on a group basis. All Schedule List Click in the schedule section on the left side of the program window.
Page 89 Click the button. The Add Schedule window will appear. Device Group Click below the item, and select the group you want to add a schedule to. Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list Select window.
Page 90: Troubleshooting Guide
Troubleshooting Guide - This program may malfunction sometimes due to a communication Issue Solution problem between the PC and display or electromagnetic waves emitted from The display you want to control does not Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). nearby electronic devices.
Page 91 How display properties are shown when multiple displays are used When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 and ID 3): The settings for ID 1 are displayed before the settings for ID 3. When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
Page 92: Screen Adjustment
Chapter 05 Screen Adjustment Picture Color Tone, etc.). Configure the settings (Backlight, Picture - The layout of the menu options may vary depending on the product. Picture Mode If the input source is PC, DVI or DisplayPort • Information: This mode reduces eye fatigue and is suitable for displaying information to the public. MENUm →...
Page 93: Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R)
Backlight / Contrast / Brightness / Your product has several options for adjusting picture quality. Input source Picture Mode Adjustable options Sharpness / Color / Tint (G/R) PC, DVI, DisplayPort, HDMI1 Information Backlight Contrast Brightness (when a PC is connected), HDMI2 Sharpness MENUm →...
Page 94: Screen Adjustment
Screen Adjustment choose size and aspect ratio picture displayed on screen. Picture Size MENUm → → → ENTERE Picture Screen Adjustment ― Different Screen Adjustment options are displayed depending on the current input source. • 16:9: Sets the picture to 16:9 wide mode.
Page 95 Picture Sizes available by Input Source. Input Source Picture Size HDMI1, HDMI2 16:9, Smart View Smart View Wide Fit, Screen Fit, (720p, 1080i, 1080p) Custom HDMI1, HDMI2 (480i, 480p) 16:9, Zoom1, Zoom2, Smart View Smart View 2, 4:3, Custom PC, DVI, DisplayPort, HDMI1(when a PC is connected), HDMI2 16:9, 4:3, Original Ratio...
Page 96: Position
Position Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Wide Fit, Screen Fit or Custom. ― To use the Position function after selecting Zoom1, Zoom2, Wide Fit Screen Fit, follow these steps. Screen Adjustment Press the ▼...
Page 97: Pc Screen Adjustment
PC Screen Adjustment Coarse Fine • Removes or reduces picture noise. If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible Screen Adjustment (Coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the Center of screen.
Page 98: Auto Adjustment
Auto Adjustment Adjust frequency values/positions and fine tune the settings automatically. MENUm → → → ENTERE Picture Auto Adjustment Picture Auto Adjustment - Available in mode only. - The displayed image may differ depending on the model. Rotation Rotate the product screen orientation. •...
Page 99: Aspect Ratio
Aspect Ratio Set the rotated screen to be either full screen or original. Full Screen: Display the rotated screen in full screen. • • Original: Display the rotated screen in the original aspect ratio. MENUm → Picture → Aspect Ratio →...
Page 100: Advanced Settings
Advanced Settings Input Source Picture Mode Advanced Settings PC, DVI, DisplayPort, HDMI1 Information White Balance Gamma (when a PC is connected), MENUm → → → ENTERE Picture Advanced Settings HDMI2 (when a PC is Advertisement Dynamic Contrast Black Tone Flesh Tone Color Space connected) White Balance...
Page 101: Dynamic Contrast
Dynamic Contrast Advanced Settings Adjust the screen contrast. Dynamic Contrast Medium Medium High • Black Tone Black Tone Flesh Tone Select the black level to adjust the screen depth. RGB Only Mode Dark Darker Darkest • Color Space Native Flesh Tone White Balance Emphasize pink Flesh...
Page 102: 10P White Balance
White Balance Advanced Settings Adjust the color temperature for a more natural picture. R-Offset G-Offset / B-Offset: Adjust each color’s (red, green, blue) darkness. • White Balance R-Gain G-Gain / B-Gain: Adjust each color’s (red, green, blue) brightness. • 10p White Balance •...
Page 103: Expert Pattern
Expert Pattern Advanced Settings Use the Expert Pattern function to calibrate the picture. If the OSD menu disappears or a menu other than the Picture menu is opened, the product saves the calibration and the White Balance Expert Pattern screen disappears. •...
Page 104: Picture Options
Picture Options Select an option using the ▲ and ▼ arrow keys, and the press E. Use the arrow keys to change the setting, and then press E. Input source Picture Mode Picture Options MENUm → Picture → Picture Options →...
Page 105: Color Tone
Color Tone Picture Options If the input source is PC, DVI, DisplayPort HDMI1 (PC connection), HDMI2 (PC connection). Color Tone Standard Cool Standard Warm • If the input source is HDMI1 or HDMI2. Color Temp. 10000K Cool Standard Warm1 Warm2 •...
Page 106: Hdmi Black Level
HDMI Black Level Picture Options Selects the black level on the screen to adjust the screen depth. Normal HDMI Black Level Normal • ― Available only in HDMI1, HDMI2 mode (AV Timing : 480p, 576p, 720p, 1080i, 1080p). Film Mode Auto Motion Plus Film Mode Dynamic Backlight...
Page 107: Dynamic Backlight
Dynamic Backlight Picture Options Automatically adjust the backlight to provide the best possible screen contrast under the current conditions. HDMI Black Level Normal • ― The Dynamic Backlight is not available when the input source is set to while Video Wall is On.
Page 108: Sound Adjustment
Chapter 06 Sound Adjustment Sound Configure the sound ( ) settings for the product. Sound Mode You can select a sound mode to suit your personal preferences. • Standard: Selects the normal sound mode. • Music: Emphasizes music over voices. MENUm →...
Page 109: Sound Effect
Sound Effect Configure your preferred sound effect for output sound. ― If Speaker Select is set to External, Sound Effect is disabled. ― Available only when Sound Mode is set to Standard. MENUm → Sound → Sound Effect → ENTERE Virtual Surround (Off / On) •...
Page 110: Speaker Settings
Speaker Settings Speaker Select (External / Internal) • If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the products speakers and the speakers attached to your audio receiver.
Page 111: Reset Sound
Reset Sound Reset all sound settings to the factory defaults. MENUm → Sound → Reset Sound → ENTERE Sound Sound Mode Standard Sound Effect Speaker Settings Reset Sound - The displayed image may differ depending on the model.
Page 112: Network
No network cable or Samsung Wireless LAN Adapter The Modem Port on the Wall External Modem connected. RJ45 (ADSL / VDSL) Please plug in a network cable or a Samsung Wireless Start LAN Adapter. Cancel Modem Cable LAN Cable • You can attach your product to your LAN by connecting the LAN port on the back of your product to an IP Sharer which is connected to an external modem.
Page 113: Wired Network Settings
Wired Network Settings • Depending on how your network is configured, you may be able to attach your product to your LAN by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN cable.
Page 114: Connecting To A Wireless Network
On the dialog that appears, click the Support tab. To connect your product to your network wireless, you need a wireless router or modem and a Samsung On the Support Tab, click the Details button. The Network connection values are displayed.
Page 115: Wireless Network Setting
― If your router, modem, or device is not certified, it may not connect to the product via the “Samsung If the Enter security key. screen appears, go to step 5. If you select a wireless router that does not Wireless LAN adapter”.
Page 116: Wps(Pbc)
How to set up manually When done, select at the bottom of the page, and then press E. The network test screen appears and the verification process starts. Go to the Network Settings screen. Select Start, press E. When the connection has been verified, the “Your wireless network and Internet connection are Network function searches for available wireless networks.
Page 117: Network Status
Network Status Wi-Fi Direct MENU m → → → ENTER E MENU m → → → ENTER E Network Network Status Network Wi-Fi Direct You can check the current network and Internet status. Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router.
Page 118: Soft Ap
Soft AP AllShare Settings MENU m → Network → Soft AP → ENTER E MENU m → Network → AllShare Settings → ENTER E Using this function, you can connect the product on your mobile devices if your mobile devices do not Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play support...
Page 119: System
Chapter 08 System Multi Control Configuring settings for Multi Control ID Setup • Assign an ID to a set. (Range: 0~99) MENUm → System → Multi Control → ENTERE Press ▲ or ▼ to select a number, and press E. Multi Control ID Input •...
Page 120: Time
Time You can configure Clock Set Sleep Timer. You can also set the product to automatically turn on or off at a specified time using the Timer function. Clock Set MENUm → System → Time → ENTERE Set the clock to use the various various timer features of the product. Time Clock Set •...
Page 121: On Timer
On Timer Time On Timer so that your product turns on automatically at a time and on a day of your choosing. On Timer The power is turned on with the specified volume or input source. Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first. Off Timer (On Timer1 Timer7)
Page 122: Off Timer
Off Timer Time Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer1 Timer7) On Timer ― You must set the clock before you can use Timer. • Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual.
Page 123: Menu Language
Menu Language Set the menu language. ― A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC. MENUm → → → ENTERE System Menu Language System Time Menu Language...
Page 124: Rotate Menu
Rotate Menu Configure the menu screen. • Landscape: Display the menu in landscape mode (default). • Portrait: Display the menu in portrait mode on the right side of the product screen. ― Available in MENUm → System → Rotate Menu →...
Page 125: Eco Solution
Eco Solution Energy Saving Reduce the power consumption by adjusting the screen brightness. MENUm → System → Eco Solution → ENTERE Selecting Picture Off switches off the screen. The volume is not disabled. To switch the screen on, press any button other than the volume button. Eco Solution Medium High...
Page 126: Security
Security Every time you access the Security functions, the PIN screen will appear and the default PIN number is "0-0-0-0" (default password: 0 - 0 - 0 - 0). Safety Lock MENUm → System → Security → ENTERE It sets safe lock function. Security •...
Page 127: Pip
PIP Settings The picture from the external video source will be in the main screen and the picture from the product will be in the PIP sub- picture screen. MENUm → System → → ENTERE Main picture Sub picture System MagicInfo Lite PC, DVI, HDMI1, HDMI2, DisplayPort...
Page 128: Auto Protection Time
Auto Protection Time If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen. 2 hours 4 hours 8 hours 10 hours •...
Page 129: Screen Burn Protection
Screen Burn Protection To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. Pixel Shift Time setting allows you to program the time between movements of the picture in minutes. MENUm →...
Page 130: Timer
Timer Screen Burn Protection Screen Burn Protection. You can set the timer for Pixel Shift Pixel Shift feature stops automatically after a specified period of time. Timer Timer Immediate Display • Side Gray • Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
Page 131: Immediate Display
Immediate Display Screen Burn Protection Select the screen saver you want to display immediately. Pixel Shift Pixel Rolling Bar Fading Screen • Timer Side Gray Immediate Display When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen. Side Gray Light Dark...
Page 132: Ticker
Ticker Input text while a video or image is displayed and display the text on the screen. • ― Message, Time, Position, Motion, and Font Options are enabled only when Ticker is set to On. MENUm → → → ENTERE System Ticker •...
Page 133: Video Wall
Video Wall Customize the layout of multiple displays that are connected to form a video wall. In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide.
Page 134: Vertical
Vertical Video Wall This function automatically divides the screen according to the specified number of vertical displays. Video Wall Enter the number of vertically arranged displays. The vertical screen will automatically be divided according to the number entered. Full · Format A maximum of 15 displays can be assigned to the vertical arrangement.
Page 135: Source Autoswitch Settings
Source AutoSwitch Settings Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. Source AutoSwitch MENUm → → → ENTERE System Source AutoSwitch Settings When the...
Page 136: General
Standby Control Auto BD Wise Wise. When Provides the optimal picture quality for Samsung DVD, Blu-ray and Home Theater products which support Wise is turned On, the picture mode is automatically changed to the optimal resolution. • - The displayed image may differ depending on the model.
Page 137: Sound Feedback
Sound Feedback General Your product gives sound feedback when you use product. Sound Feedback Sound Feedback is enabled by default. Turn off Sound Feedback or adjust its volume. This function is enabled by default. The volume can be adjusted or muted. Auto Power ―...
Page 138: Lamp Schedule
Lamp Schedule General Enables the lamp value to be adjusted to a user-specified value at a specified time in MDC mode. Sound Feedback • Auto Power OSD Display Standby Control Auto Displays or hides a menu item on the screen. Lamp Schedule ―...
Page 139: Anynet+ (Hdmi-Cec)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your MENUm →...
Page 140: Auto Turn Off
Auto Turn Off Anynet+ (HDMI-CEC) Setting an Anynet+ Device to turn automatically when the product is turned off. Anynet+ (HDMI-CEC) • ― If Auto Turn Off Auto Turn Off is set to Yes, running external devices will turn off at the same time as the product powers off. ―...
Page 141: Troubleshooting For Anynet
Troubleshooting for Anynet+ Problem Possible Solution Anynet+ does not work. • Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only. • Check if the Anynet+ device power cord is properly connected. • Check the Anynet+ device’s Video/Audio/HDMI cable connections. Anynet+ (HDMI-CEC) •...
Page 142 Problem Possible Solution The connected device is not • Check whether or not the device supports Anynet+ functions. displayed. • Check whether or not the HDMI cable is properly connected. • Check whether Anynet+ (HDMI-CEC) is set to in the Anynet+ Setup menu.
Page 143: Divx® Video On Demand
DivX ® Video On Demand Shows the registration code authorized for the product. If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file. For more information about DivXⓇ VOD, visit “http://vod.divx.com”. MENUm →...
Page 144: Magic Clone
Clone to USB ― The option is available for products with the same Model Code Software Version. Support → Contact Samsung Model Code Software Version. Go to and find the product Clone From USB - The displayed image may differ depending on the model.
Page 145: Reset All
Reset All This option returns all the current settings for a display to the default factory settings. MENUm → System → Reset All → ENTERE System Reset All - The displayed image may differ depending on the model. PC Module Power The PC module can be turned on/off separately from the LFD.
Page 146: Support
By USB - Please be careful not to remove the USB To perform a software update from a USB device, contact the customer service center. drive until the upgrade is complete. Contact Samsung MENUm → → → ENTERE Support Contact Samsung View this information when your product does not work properly or when you want to upgrade the software.
Page 147: Contents Home
Contents Home MagicInfo Lite MENU m → Support → Contents Home → MagicInfo Lite → ENTER E ― MENUm → Support → Contents Home → ENTERE MagicInfo Lite can also be accessed by pressing MagicInfo Lite/S on the remote control. ―...
Page 148: Allshare Play
AllShare Play MENU m → Support → Contents Home → AllShare Play → ENTER E Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device. ― Refer to page 149 for details about the AllShare Play menu.
Page 149: Allshare Play
• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost. Samsung Electronics is not liable for any damage or loss of data. • Do not remove a USB device while it is loading.
Page 150 Compatible devices with AllShare Play • Some types of USB devices, digital cameras and audio devices may not be compatible with the product. AllShare Play is only compatible with USB MSC devices. • • MSC device refers to a Mass Storage Class Bulk-Only Transport device. Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.) These MSC devices must be connected directly to a USB port on the product.
Page 151: Using A Usb Device
Using a USB device Connecting a USB device Turn on your product. It is recommended to use a USB HDD that has a power adapter. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. A message New device connected.
Page 152: Connecting To A Pc Over A Network
Settings. • To view content saved on the PC, connect the product and PC to the same wireless router and visit http://www.samsung.com to download the AllShare PC software. • Ensure the product and PC are connected to the same network subnet.
Page 153: Using The Allshare Play Features
• Compatibility with various subtitle formats (SRT, SMI, SUB, TXT, TTXT) • Search with file names • And many others ― A compatibility issue may occur if a video file is played when a server not provided by Samsung Electronics is connected. ― To use AllShare...
Page 154: Using The Basic Allshare Play Features
Using the Basic AllShare Play Sorting the file lists Features To sort files, press on the remote control to specify the sorting criteria. Sort Criteria Operation Videos Photos Music MENUm → → → → ENTERE Support Contents Home AllShare Play Folder view Displays the whole folder.
Page 155: Playing Selected Files
Playing Selected Files Creating a Playlist Select files from the list of Videos, Photos, or Music files. Select files from the list of Videos, Photos, or Music files. Press TOOLS on the remote control and select Selection Play. Press TOOLS on the remote control and select Add to Playlist.
Page 156: My List
My List MENUm → → → → → ENTERE Support Contents Home AllShare Play My List Access desired content more conveniently and quickly. Playlist To play files, select files or a and press E. Recently Played: Display video, photo or music files that were recently played. This mode is suitable when playing files again that were played before. •...
Page 157: Videos
Videos MENUm → → → → → ENTERE Support Contents Home AllShare Play Videos Playing a Video Select the internal memory or a USB device. Select files from the list of files. Press the E button or ∂ (Play) button. •...
Page 158: Photos
Photos MENUm → → → → → ENTERE Support Contents Home AllShare Play Photos Viewing a Photo (or Slide Show) Select the internal memory or a USB device. Select a file from the list of files. Press the E button. •...
Page 159: Music
Music MENUm → → → → → ENTERE Support Contents Home AllShare Play Music Playing Music Select the internal memory or a USB device. Select files from the list of files. Press the E button or ∂(Play) button. • When the music is playing, you can search using the π(REW) and µ(FF) button. ―...
Page 160: Videos / Photos / Music Play Option Menu
Videos / Photos / Music Play Option menu When playing video or photo files, you can press the TOOLS button to display an Options menu. - Pressing the INFO button while a device name is selected will display Option Name Operations Videos Photos...
Page 161 Option Name Operations Videos Photos Music Sound Mode You can change the Sound Mode. Audio Language You can enjoy video in one of supported languages. The function is enabled only when you play stream-type files which support multiple audio formats. Subtitle You can view a subtitle.
Page 162: Supported Subtitle And Allshare Play File Formats
Supported Subtitle and AllShare Play file formats Subtitle External Internal • MPEG-4 timed text (.ttxt) • Xsub Container: AVI • SAMI (.smi) • SubStation Alpha • SubRip (.srt) Container: MKV • SubViewer (.sub) • Advanced SubStation Alpha • Micro DVD (.sub or .txt) Container: MKV •...
Page 163: Supported Music File Formats
Supported music file formats File Extension Type Codec Comments *.mp3 MPEG MPEG1 Audio Layer 3 *.m4a, *.mpa, *.aac, *.3ga MPEG4 *.flac FLAC FLAC The Seek (jump) function is not supported. Supports up to 2 channel Supported Video Formats • Video content will not play, or not play correctly, if there is an error in the content or the container. •...
Page 164 File Container Video Codec Resolution Frame rate Bit rate Audio Codec Extension (fps) (Mbps) *.avi DIVX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf ADMPCM MPEG4 SP / ASP *.wmv (IMA, MS) *.mp4 *.mov HE-AAC H.264 BP / MP / HP *.3gp...
Page 165: Magicinfo Lite
Chapter 11 MagicInfo Lite File Formats Compatible with MagicInfo Lite Player MagicInfo Lite, select - To launch MagicInfo Lite for the Player Mode the System. Read before using MagicInfo Lite Player • Supported file systems include FAT32 and NTFS. • A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played. Check the vertical and horizontal resolution of the file.
Page 166 Contents File Extension Container Video Codec Resolution Frame rate Bit rate Audio Codec (fps) (Mbps) *.avi DIVX 3.11 / 4.x / 5.x / 6.x 1920 x 1080 6~30 *.mkv LPCM *.asf MPEG4 SP / ASP *.wmv HE-AAC *.mp4 *.mov H.264 BP / MP / HP *.3gp MPEG(MP3) *.vro...
Page 167 Video Audio Image • 3D video is not supported. • Audio content with a Bit rate or Frame rate • Compatible image file format : Jpeg larger than the rate specified in the table above • Content with a resolution larger than the •...
Page 168 Flash Power Point • Compatible with Flash 10.1 • Compatible document file formats • Flash Animation - Extension : ppt, pptx - Version : Office 97 ~ Office 2007 - Compatible file format : SWF • Functions not supported • Recommended resolution : 960 x 540 - Caution - Animation effect - 3D shapes (which will be displayed in 2D)
Page 169 WORD • Compatible document file formats • Compatible document file formats - Extension : pdf - Extension : .doc, .docx - Version : Office 97 ~ Office 2007 • Functions not supported - Content less than 1 pixel not supported because of performance •...
Page 170: Approving A Connected Device From The Server
Approving a connected device from the Select Lite from the menus on the left. server Unapproved from the sub-menus of Lite. Select ― First configure the server network settings before device approval. (page 184) Access the server you have assigned to your device. Select the Approve button for your device from the list of unapproved Lite devices.
Page 171: Setting The Current Time
Enter the information required to approve the device. When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. ― For further details on how to configure a schedule, refer to the <MagicInfo Lite Server user's manual>. ―...
Page 172: Magicinfo Lite
MagicInfo Lite Select Network Schedule in the MagicInfo Lite Player menu. MagicInfo Lite Player MENUm → Support → Contents Home → MagicInfo Lite → ENTERE ― To launch Network Schedule MagicInfo Lite, select MagicInfo Lite for the Player Mode on the System. Local Schedule ―...
Page 173 Local Schedule → Click to create a schedule → Select the schedule you want to run → Go to Local Schedule Manager Create Local Schedule MagicInfo Lite Player Select in the menu screen. MagicInfo Lite Player Run schedules created in Local Schedule Manager.
Page 174 ― To enable and use the option, ensure at least one content file is saved in the "MagicInfoSlide" folder on the USB device. The USB AutoPlay content file must be a file other than a music or text file. ― Ensure a USB device is inserted. Be sure to create a folder named "MagicInfoSlide" in the USB device and put content in the MagicInfo Lite Player folder.
Page 175: Local Schedule Manager
Local Schedule Manager Create Local Schedule Manager Select in the screen. Configure the settings for playback from Local Schedule. Local Schedule Manager Alternatively, select and play content from internal or USB memory according to the customized playback Create sequence. Storage Internal Memory Edit No Playing Schedule...
Page 176 Content Select Duration. Select to specify the content you want to play. Content Direction Internal Memory Content Duration Localschedule Folder1 Menu1.jpg 00:00:05 Menu1.jpg Menu2.jpg 00:00:05 Menu2.jpg Cancel Down Save Deselect Duration Cancel Return Return Specify the sequence and time duration to play content files. - A maximum of 99 content files can be selected.
Page 177 Select Save. Select the memory space you want to save the content to. Modifying a Local Schedule ― Ensure at least one Local Schedule is registered. Create Select Local Schedule Manager in the MagicInfo Lite menu screen. Time --:-- am~ --:-- pm Delete Content Menu1.jpg Menu2...
Page 178 Deleting a Local Schedule Change the details of the local schedule. Next, select Save. ― Ensure at least one Local Schedule is registered. Edit ― If a copied local schedule is deleted, content files in the schedule will also be deleted. Time 12:00 am~ 12:00 pm Delete...
Page 179 Running a Local Schedule Stopping a Local Schedule ― Ensure at least one ― This option is available only when a schedule is running. Local Schedule is registered. Selecting Stop will change the running mode from Local Schedule Network Schedule. Select Local Schedule Manager in the...
Page 180 Viewing the details of a Local Schedule The details of the schedule will be displayed. Select Local Schedule Manager in the MagicInfo Lite menu screen. Information 2012.01.01_1834.lsch MagicInfo Lite 00:00 ~ 00:00, 2 File(s) - Menu1.jpg Menu2.jpg MagicInfo Lite Player Local Schedule Manager Close Content Manager...
Page 181 Copying a Local Schedule Select local schedule files and press Copy. Select Local Schedule Manager in the MagicInfo Lite menu screen. Local Schedule Manager Storage Internal Memory Create MagicInfo Lite Edit No Playing Schedule MagicInfo Lite Player Delete All Schedules Local Schedule Manager 2012.01.01_1834.lsch Content Manager...
Page 182: Content Manager
Content Manager Select the content you want to copy. Content Manager Copying content Internal Memory Select Content Manager in the MagicInfo Lite menu screen. Folder1 Localschedule Menu1.jpg Menu2.jpg MagicInfo Lite Player MagicInfo Lite Player Copy Local Schedule Manager Delete Free Space Free Space 5549.2MB 6227.2MB...
Page 183 Deleting content Select the content you want to delete. Next, select Delete. Internal Memory • Content under memory can be deleted at the same time. Select Content Manager in the MagicInfo Lite menu screen. Content Manager MagicInfo Lite Player Internal Memory MagicInfo Lite Player Localschedule Folder1...
Page 184: Settings
Settings Server Network Settings MagicInfo Lite, connect to a network. To run Settings Server Server Network Settings Enter the MagicInfo Lite server settings. Content Default Duration Content Ratio (E.g.: http://192.168.0.10:7001/MagicInfo/) Image Effect Random Close • If the option is enabled, the server is configured to use https and data transfer is encrypted. Default Content None ―...
Page 185 Content Default Duration Content Layout Landscape Portrait Specify the duration to play content. Switch the orientation of playing content to mode. Image Viewer Time, Doc Viewer Time, PPT Viewer Time, PDF Viewer Time, Flash Viewer Time Landscape Portrait • • ―...
Page 186: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Device Name: Displays the name of a device recognized by the server • Viewing the details of the content that is running Device ID: Displays the original identification number of a device •...
Page 187 Changing the settings for the content that is running Press the TOOLS button on the remote control. You can change the Picture Mode Sound Mode setting or safely remove a USB device (Safely Remove USB) while content Tools is playing by pressing the TOOLS button on the remote control. Picture Mode (Dynamic Standard Natural...
Page 188: Magicinfo Premium S
MagicInfo Premium S A license needs to be purchased to use MagicInfo Premium MagicInfo Premium S, select - To launch To download the software, go to the Samsung homepage at http://www.samsunglfd.com. MagicInfo Premium S for the Player Mode on the System.
Page 189 Video Audio Image • 3D video is not supported. • Audio content with a Bit rate or Frame rate • Compatible image file format : Jpeg larger than the rate specified in the table above • Content with a resolution larger than the •...
Page 190 Flash Power Point • Compatible with Flash 10.1 • Compatible document file formats • Compatible document file formats - Extension : ppt, pptx - Extension : pdf • Flash Animation - Compatible file format : SWF - Version : Office 97 ~ Office 2007 •...
Page 191 WORD Template files • Compatible document file formats • Creation/editing/playback are only available in • Supported in USB AutoPlay Network Template Manager. - Extension : .doc, .docx Schedule (Authored in a PC authoring tool for - Version : Office 97 ~ Office 2007 Premium S Player) •...
Page 192 Network Schedule Multiframe Playback restrictions • A maximum of two video files (Videos) can be played simultaneously. • In portrait playback mode, only one video file can be played at a time. • If mode is enabled, more than one video (Videos) file cannot be played. •...
Page 193 Playback restrictions • A maximum of two video (Videos) files can be played. • If mode is enabled, more than one video (Videos) file cannot be played. • More than one Flash file cannot be played. Office • For files (PPT and Word files) and files, only one file type is supported at a time.
Page 194: Approving A Connected Device From The Server
Approving a connected device from the Select Premium from the menus on the left. server Unapproved from the sub-menus of Premium. Select ― First configure the server network settings before device approval. (page 211) Access the server you have assigned to your device. Select the Approve button for your device from the list of unapproved Premium devices.
Page 195 Enter the information required to approve the device. When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. ― For further details on how to configure a schedule, refer to the <MagicInfo Premium Server user's manual>.
Page 196: Magicinfo Premium S
MagicInfo Premium S Network Schedule MagicInfo Premium S Player Select in the menu. MagicInfo Premium S Player MENU m : T Support Contents Home MagicInfo Premium S ENTER E ― To launch Network Schedule MagicInfo Premium S, select MagicInfo Premium S Player Mode for the on the...
Page 197 Local Schedule → Click to create a schedule → Select the schedule you want to run → Go to Local Schedule Manager Create Select Local Schedule in the MagicInfo Premium S Player menu screen. MagicInfo Premium S Player Run schedules created in Local Schedule Manager.
Page 198 ― To enable and use the option, ensure at least one content file is saved in Internal AutoPlay Internal Memory. The content file must be a file other than a music or text file. MagicInfo Premium S Player Internal AutoPlay MagicInfo Premium S Player Select in the...
Page 199: Local Schedule Manager
Local Schedule Manager Select Create in the Local Schedule Manager screen. Local Schedule. Configure the settings for playback from Local Schedule Manager Alternatively, select and play content from internal or USB memory according to the customized playback Create sequence. Storage Internal Memory Edit No Playing Schedule...
Page 200 Select Content to specify the content you want to play. Select Duration. Content Direction Internal Memory Content Duration Localschedule Folder1 Menu1.jpg 00:00:05 Menu1.jpg Menu2.jpg 00:00:05 Template Menu2.jpg Down Cancel Deselect Save Duration Cancel Return Return Specify the sequence and time duration to play content files. - A maximum of 99 content files can be selected.
Page 201 Select Save. Select the memory space you want to save the content to. Modifying a Local Schedule ― Ensure at least one Local Schedule is registered. Create Select Local Schedule Manager in the MagicInfo Premium S menu screen. Time --:-- am~ --:-- pm Delete Content Menu1.jpg Menu2...
Page 202 Change the details of the local schedule. Next, select Save. Deleting a Local Schedule ― Ensure at least one Local Schedule is registered. Edit ― If a copied local schedule is deleted, content files (except for template files) in the schedule will also Time 12:00 am~ 12:00 pm be deleted.
Page 203 Running a Local Schedule Stopping a Local Schedule ― Ensure at least one ― This option is available only when a schedule is running. Local Schedule is registered. Selecting Stop will change the running mode from Local Schedule Network Schedule. Select Local Schedule Manager in the...
Page 204 Viewing the details of a Local Schedule The details of the schedule will be displayed. Select Local Schedule Manager in the MagicInfo Premium S menu screen. Information 2012.01.01_1834.lsch MagicInfo Premium S 00:00 ~ 00:00, 2 File(s) - Menu1.jpg Menu2.jpg MagicInfo Premium S Player Local Schedule Manager Close Template Player...
Page 205 Copying a Local Schedule Internal Memory → USB: Content files (except for templates) in a copied schedule are saved • to a subfolder under the local schedules folder on the memory device. The subfolder is assigned the schedule name. If a content file in a copied schedule contains a template file, the Select Local Schedule Manager in the...
Page 206: Template Manager
Template Manager Select Create in the Template Manager screen. Template Manager Registering a Template Create Storage Internal Memory Select Template Manager in the MagicInfo Premium S menu screen. Edit No Playing Schedule Copy MagicInfo Premium S Delete Play MagicInfo Premium S Player Preview Local Schedule Manager Close...
Page 207 Message Organize a template by inserting text, video, photo, or PDF files as desired. Message Create Message None Select the position and background. Scroll None Use background image Alignment Center Preview Color White Previous Cancel Next Return Cancel • Message: Select a message input mode. - None: Select this mode if you do not want to input a message.
Page 208 Content Select Sound/Background music. Content Create Type None Select Sound/Background music. Content No Item Background Music Size Fit to screen Preview Source Previous Cancel Next Return Cancel • Type: Select a file type to use to organize a template. None Videos Image Flash...
Page 209: Content Manager
Content Manager Specify Storage and change the Template Name. Select OK. Create Copying content Save the template and finish. Select Content Manager in the MagicInfo Premium S menu screen. Storage Internal Template Name 20130101_2222 Preview MagicInfo Premium S Previous MagicInfo Premium S Player Local Schedule Manager Template Manager Cancel...
Page 210 Deleting content Select the content you want to copy. Select Content Manager in the MagicInfo Premium S menu screen. Content Manager Internal Memory MagicInfo Premium S Deployed Folders Deployed Folders Menu1.jpg MagicInfo Premium S Player Menu2.jpg Local Schedule Manager Template Manager Copy Content Manager Close...
Page 211: Settings
Settings Server Network Settings MagicInfo Premium S, connect to a network. To run Settings Server Server Network Settings Enter the MagicInfo Premium S server settings. Content Default Duration • If the option is enabled, the server is configured to use https and data transfer is encrypted. Content Ratio ―...
Page 212 Content Default Duration Content Layout Landscape Portrait Specify the duration to play content. Switch the orientation of playing content to mode. ― Image Viewer Time, Template Viewer Time, Doc Viewer Time, PPT Viewer Time, PDF Viewer Time, Landscape Portrait • Flash Viewer Time ―...
Page 213: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Device Name: Displays the name of a device recognized by the server • Viewing the details of the content that is running Device ID: Displays the original identification number of a device •...
Page 214 Changing the settings for the content that is running Press the TOOLS button on the remote control. You can change the Picture Mode Sound Mode setting or safely remove a USB device (Safely Remove USB) while content Tools is playing by pressing the TOOLS button on the remote control. Picture Mode (Dynamic Standard Natural...
Page 215: Magicinfo Videowall S
MagicInfo Videowall S A license needs to be purchased to use MagicInfo Videowall MagicInfo Videowall - To launch To download the software, go to the Samsung homepage at http://www.samsunglfd.com. select MagicInfo Videowall S for the Player Mode on the System.
Page 216 Video Image • 3D video is not supported. • Compatible image file format : Jpeg, bmp, png • Content with a resolution larger than the resolution specified in the table • Supported maximum resolution : 15,360 x 8,640 above is not supported. - A higher resolution image may take longer to display on the screen.
Page 217 Restrictions • Only one video (Videos) file can be played per client. ― Different content files can be played on the displays of a video wall. Two video (Videos) files cannot be played on a single display of a video wall. Available Available Not available...
Page 218: Magicinfo Videowall S
MagicInfo Videowall S Default Storage Specify the location you want to save content (downloaded from the server) to. Internal Memory: Save the content to the internal memory of the product. • MENUm → Support → Contents Home → MagicInfo Videowall S →...
Page 219: When Content Is Running
When Content is Running Press the INFO button on the remote control. Software Version: Displays the software version of a device • Information Device Name: Displays the name of a device recognized by the server • Device ID: Displays the original identification number of a device •...
Page 220: Troubleshooting Guide
Chapter 14 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center Before calling Samsung Customer Service Testing the Product Center, test your product as follows. If the problem persists, contact Samsung Check if your product is operating normally by using the product test function.
Page 221: Check The Followings
Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product.
Page 222 Screen issue The screen is not clear. The screen is blurry. Adjust Coarse and Fine. Remove any accessories (video extension cable, etc) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product.
Page 223 Lines (red, green or blue) are displayed on the screen. These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a Samsung Service Center to resolve the issue. The display looks unstable and then freezes.
Page 224 Sound issue There is no sound. Check the connection of the audio cable or adjust the volume. Check the volume. The volume is too low. Adjust the volume. If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software program.
Page 225 Sound issue There is audible sound when the volume is muted. Speaker Select is set to External, the volume button and mute function are disabled. When Adjust the volume for the external speakers. Audio settings for main speakers are separate from the internal speakers on the product. Changing or muting the volume on the product does not affect an external amplifier(decoder).
Page 226 Other issue The product smells like plastic. The plastic smell is normal and disappears over time. The monitor appears tilted. Remove and then attach the stand again to the product. Audio or video cuts out intermittently. Check the cable connection and connect it again if required. Using a very hard or thick cable may corrupt audio and video files.
Page 227 Other issue The IR sensor is not functioning. Make sure the sensor light turns on when a button is pressed on the remote control. • If the sensor light does not turn on, turn the power switch off and then on again on the back of the product.
Page 228: Q & A
Q & A Question Answer How can I change the frequency? Set the frequency on your graphics card. • Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings. •...
Page 229 Question Answer • Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display How do I set powersaving mode? → Screen Saver Settings or BIOS SETUP on the PC. • Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver Settings or BIOS SETUP on the PC.
Page 230: Specifications
Chapter 15 Specifications General Size Model Name ME32C ME40C Panel Size 32 CLASS (31.5 inches / 80 cm) 40 CLASS (40.0 inches / 101 cm) Display area 698.4 mm (H) x 392.85 mm (V) 885.6 mm (H) x 498.15 mm (V) 27.5 inches (H) x 15.5 inches (V)
Page 231 Display Color 16.7 M Synchronization Horizontal 31 ~ 80 kHz Frequency Vertical 56 ~ 75 Hz Frequency Resolution Optimum 1920 x 1080 @ 60 Hz resolution Maximum 1920 x 1080 @ 60 Hz resolution Maximum Pixel Clock 148.5 MHz (Analog, Digital) Audio Output 10 W + 10 W Power Supply...
Page 232 ― Plug-and-Play This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired. ―...
Page 233: Powersaver
PowerSaver Normal Operation Power saving mode Power off Power off (Power Button off) Rating Typical Power Indicator Blinking Power Consumption ME32C 70 W 62 W 0.5 W 0.4 W ME40C 100 W 93 W ME46C 110 W 97 W ME55C...
Page 234: Preset Timing Modes
Preset Timing Modes ― This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product. - Horizontal Frequency Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product.
Page 235 Resolution Horizontal Frequency Vertical Frequency Pixel Clock Sync Polarity (kHz) (Hz) (MHz) (H/V) VESA, 1024 x 768 56.476 70.069 75.000 VESA, 1024 x 768 60.023 75.029 78.750 VESA, 1152 x 864 67.500 75.000 108.000 VESA, 1280 x 720 45.000 60.000 74.250 VESA, 1280 x 800 49.702...
Page 236: Contact Samsung World Wide
Chapter 16 Appendix Contact SAMSUNG WORLD WIDE ― If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us http://www.samsung.com/ca (English) CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca_fr (French) LATIN AMERICA...
Page 237 LATIN AMERICA http://www.samsung.com/latin (Spanish) COSTA RICA 0-800-507-7267 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) DOMINICA 1-800-751-2676 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) ECUADOR 1-800-10-7267 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) EL SALVADOR 800-6225 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) GUATEMALA 1-800-299-0013 http://www.samsung.com/latin_en (English) http://www.samsung.com/latin (Spanish) HONDURAS 800-27919267 http://www.samsung.com/latin_en (English)
Page 238 LATIN AMERICA TRINIDAD & TOBAGO 1-800-SAMSUNG (726-7864) http://www.samsung.com URUGUAY 000 405 437 33 http://www.samsung.com VENEZUELA 0-800-100-5303 http://www.samsung.com/ve...
Page 239: Responsibility For The Pay Service (Cost To Customers)
― When the service is requested, in spite of in warranty, we may charge you for a visit from a service • Use of supplies or separatly sold product unspecified by Samsung. technician in the following cases. • Repair from a person besides an engineer of outsourcing service company or partner of Samsung Electronics Co., Ltd. Not a product defect •...
Page 240: Optimum Picture Quality And Afterimage Burn-In Prevention
Optimum Picture Quality and Afterimage Burn-in Prevention Optimum Picture Quality • To enjoy the optimum picture quality, go to Control Panel on your PC and adjust the resolution and refresh rate as follows. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. - Resolution: 1920 x 1080 - Vertical frequency (refresh rate): 56 ~ 75 Hz Screen refresh rate: refers to the number of times a display image is refreshed per second.
Page 241: Prevention Of Afterimage Burn-In
What is afterimage burn-in? Prevention of Afterimage Burn-in Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight Black Matrix Color-Filter Common...
Page 242 • Avoid combinations of a text color and background color of contrasting brightness. ― Avoid using grey as it may contribute to afterimage burn-in. ― Avoid using colors of contrasting brightness (black and white; grey). - Brightness: refers to the lightness or darkness of a color which varies FLIGHT TIME...
Page 243: License
License Manufactured under license from Dolby Laboratories. DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content. Dolby and the double-D symbol are trademarks of Dolby Laboratories. DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of DivX, Inc. and are used under license.
Page 244: Terminology
Terminology 480i / 480p / 720p / 1080i / Non-interlace Mode and Interlace Vertical Frequency____ The product Plug & Play____ Plug & Play is a DVD (Digital Versatile Disc)____ DVD 1080p____ Each of the scanning Mode____ Non-interlace mode displays a single image many times function that allows the automatic refers to a CD-sized mass storage disk rates above refers to the number of...

This manual is also suitable for:

Me46c Me40c Me55c Me75c

Samsung ME32C User Manual

Copyright

Safety Precautions

Storage

Checking the Contents

Parts

Before Installing the Product (Installation Guide)

Dimensions

Installing the Wall Mount

Remote Control (RS232C)

Before Connecting

Connecting to a PC

Changing the Resolution

Connecting to an Audio System

Connecting an External Monitor

Connecting the Network Box (Sold Separately)

Changing the Input Source

Configuring Settings for Multi Control

MDC Program Installation/Uninstallation

What Is MDC

Getting Started with MDC

Picture Mode

Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R)

Sharpness / Color / Tint (G/R) 93

Screen Adjustment

Auto Adjustment

Rotation

Aspect Ratio

Advanced Settings

Picture Options

Reset Picture

Sound Mode

Sound Effect

Speaker Settings

Reset Sound

Network Settings

Network Status

Wi-Fi Direct

Soft AP

Allshare Settings

Device Name

Multi Control

Time

Menu Language

Rotate Menu

Eco Solution

Security

Pip

Auto Protection Time

Screen Burn Protection

Ticker

Video Wall

Source Autoswitch Settings

General

Anynet+ (HDMI-CEC)

DIVX® Video on Demand

Player Mode

Magic Clone

Reset System

Reset All

PC Module Power

Software Update

Contact Samsung

Contents Home

What Is Allshare Play

Using the Basic Allshare Play Features

My List

Videos

Photos

Music

Videos / Photos / Music Play Option Menu

Supported Subtitle and Allshare Play File Formats

File Formats Compatible with Magicinfo Lite Player

Approving a Connected Device from the Server

Magicinfo Lite

File Formats Compatible with Magicinfo Premium S Player

Approving a Connected Device from the Server

Device from the Server 194

Magicinfo Premium S

File Formats Compatible with Magicinfo Videowall S Player