Sony XR-C4120 Service Manual page 26

Pin No. Pin Name I/O
37 AMP ON
38 PLL-CKO
39 PLL-CE
40 PLL-SO
41 PLL-SI
42 LCD-SO
43 LCD-CE
44 LCD-CKO
45 VOL-SIO I/O
46
NCO
47 VOL-CKO
48 ACC-IN
49 MUT
50
NCO
51 AMSON
52 N/R-OUT
53 MTLON I/O
54 TAPE-MUT
55 DOLON I/O
56 AMSIN
57 to 75
NCO
76 ST-MONO I/O
77 SD-IN
78 RE-IN0
79 RE-IN1
80 AD-ON
81 POWSEL
82
ILL-ON
83 REEL
Standby on/off control signal output to the power amplifier (IC751)
O
"L": standby mode, "H": amp on
O
PLL serial data transfer clock signal output to the FM/AM PLL (IC21)
O
PLL chip enable signal output to the FM/AM PLL (IC21) "H" active
O PLL serial data output to the FM/AM PLL (IC21)
I
PLL serial data input from the FM/AM PLL (IC21)
O Serial data output to the liquid crystal display driver (IC901)
O Chip enable signal output to the liquid crystal display driver (IC901) "H" active
O Serial data transfer clock signal output to the liquid crystal display driver (IC901)
Two-way data bus with the electrical volume (IC331)
O
Not used (open)
O
Bus clock signal output to the electrical volume (IC331)
I Accessory detect signal input terminal "L": accessory on
O Audio line muting on/off control signal output terminal "H": muting on
O
Not used (open)
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
O
"L" is output to lower the gain for audio level at FF/REW mode
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
O
"L": forward direction, "H": reverse direction
METAL control in/out terminal
At initial mode: valid/invalid selection input of METAL function (valid at "L" input)
At normal mode: METAL on/off control signal output to the CXA2509AQ (IC301)
(METAL on at "H" output)
Tape muting on/off control signal output to the CXA2509AQ (IC301) "H": muting on
O
Active at ATA, FF/REW mode
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (valid at "L" input)
At normal mode: dolby on/off control signal output terminal (dolby on at "H" output)
Not used this function (fixed at "H")
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
I
"L": music is present, "H": music is not present
O
Not used (open)
FM stereo broadcasting detection signal input from the FM/AM tuner unit (TU1), or forced
monaural control signal output to the FM/AM tuner unit (TU1)
"L" is input in the FM stereo mode, or "L" is output in the forced monaural mode
Station detector detect input from the FM/AM tuner unit (TU1)
I
Stop level for SEEK, BTM, etc. is determined SD is present at input of "H"
I
Dial pulse input of the rotary encoder (RE900)
(for VOLUME/BASS/TREBLE/BALANCE/FADER control)
I
A/D converter power control signal output terminal
When the KEYACK (pin @§) that controls reference voltage power for key A/D conversion input
O
is active, "L" is output from this terminal to enable the input
I Power select switch (S501) input terminal "L": off (halt mode), "H": on (operation mode)
Power on/off control signal output of the illumination LED and liquid crystal display driver
(IC901) "H": power on Depends on initial setting of power select switch (S501)
O
Power select switch (S501) on: "H" output at the accessory on
Power select switch (S501) off: "H" output at the power on
Rotation detect signal input from supply reel sensor and take-up reel sensor on the deck
I
mechanism
Function
– 32 –