Module Wiring the mounting instructions below. Array Wiring Earth Ground Wiring SANYO is part of the Panasonic Group and is Grounding Locations in charge of the manufacturing process for Grounding Methods ®...
Edition Revision Date Revised Item Revised Content New Edition 2013.4.19 (1) Addition of System Fire Class Rating (1) System Fire Class Rating (2) Explanation of trademark Edition 2015.3.18 (2) Trademark (3) According to UL1703 Edition 3 (3) Front cover, Grounding –...
Completely ground all modules. installing or using your Panasonic PV modules. inspection requirements, which should be Do not disassemble a module, attempt any This section contains important electrical and followed. repair, open the junction box cover, nor mechanical specifications.
0.12”(3 mm) or more (11mm) Material: Aluminum Alloy (6005-T5, 0.2” 6105-T5, 6061-T6) (5mm) Panasonic does not provide a warranty for clamps. module warranty Panasonic provides shall be voided if clamps selected M8 Bolt customer improper M8 Nut material or size...
IEC 60904-3. Note: At the appropriate FUSE for each series string or only at the locations marked in this manual time of shipment, Panasonic guarantees the each module. (see grounding methods below). ...
No.10 (0.190’‘ diameter (4.83mm)). Lay-in lugs or grounding clips can be used used grounding connections This method requires a minimum number of to ground Panasonic PV modules. Both accordance with instructions provided threads-per-inch to achieve an adequate methods explained below, please with the module.
A junction box as a terminal enclosure is Contact your Panasonic Authorized instructions previous section regarding equipped for electrical connections. Representative for proper diode type, if it is using bolts and nuts with larger grounding...
The return of any modules will not be accepted by Panasonic unless prior written authorization has been given by Panasonic. As part of Panasonic’s policy of continuous improvement, Panasonic reserves the right Cable Connector Plug Option:...
Page 9
Glass Figure 3.2 (Method 1) Grounding method using self-tapping machine screw Backsheet Frame (Longer side) Note: the smaller ground holes illustrated in Figure 3.1. Grounding hole *If using a brass cup washer, a flat (0.165’‘ diameter (4.2 mm) ) washer must be inserted between the cup washer and module frame, and the flat washer diameter must be greater *Flat washer (Stainless steel)
Page 10
Figure 3.4 Glass Frame (Longer side) Grounding method Backsheet Using self-tapping machine screw Note: smaller ground holes illustrated in Figure 3.1. Grounding hole Select a grounding the following lug. (0.165” diameter (4.2mm)) ILSCO GBL-4DBT, Star washer (Stainless steel) Burndy CL501TN Thickness: not less than 0.02”...
Page 11
Figure 3.6 Grounding method Frame (Longer side) Using Grounding Clip with self-tapping Glass machine screw Backsheet Note: the smaller ground holes illustrated in Figure 3.1. Grounding Clip Assemblies: Tyco Grounding hole Electronics 1954381-1. (0.165” diameter (4.2mm)) Self-tapping machine screw (Stainless steel) Length (not less than 0.47’‘(12 mm) not more than 0.78’‘(20 mm))
Page 12
SPECIFICATIONS Electrical Specifications Model HIT Power 240S HIT Power 235S HIT Power 230S VBHN240SA11 VBHN235SA11 VBHN230SA11 VBHN240SA11B VBHN235SA11B VBHN230SA11B Cell Number in Series Rated Power, Watts (Pmax) Maximum Power Voltage (Vpm) 43.7 43.0 42.3 Maximum Power Current (Ipm) 5.51 5.48 5.45 Open Circuit Voltage (Voc) 52.4...