Table of Contents
Advertisement
Quick Links
General Installation Manual
Photovoltaic Module HIT
VBHNxxxSA16 series
Thank you for choosing Panasonic HIT
read this manual completely before installation
or use of Panasonic PV(photovoltaic) modules.
With
proper
operation
and
®
Panasonic HIT
will provide you with clean,
renewable solar electricity for many years. This
manual
contains
important
maintenance and safety information. The word
"module" as used in this manual refers to one
or more PV modules.
Retain this manual for
future reference. The module is considered to
be in compliance with UL 1703 only when the
module is mounted in the manner specified by
the mounting instructions below.
SANYO is part of the Panasonic Group and is
in charge of the manufacturing process for
®
Panasonic HIT
.
VBHNxxxSA16 series
®
Model No.
VBHN330SA16 and 16B
VBHN325SA16 and 16B
®
. Please
maintenance,
installation,
Contents
Please read before installation
Note on Specifications
Grounding Methods
Customer Services
"HIT" is a registered trademark of Panasonic
Group.
Other product and service names listed in this
manual are trademarks or registered trademarks
of their respective companies.
1
:3
:3
:3
:3
:3
:3
:3
:5
:5
:5
:5
:5
:5
:5
:5
:5
:6
:6
:7
:7
:7
:7
:7
:8
:8
Advertisement
Table of Contents
Related Manuals for Panasonic VBHN330SA16
Summary of Contents for Panasonic VBHN330SA16
-
Page 1: Table Of Contents
Unpacking and handling module is mounted in the manner specified by the mounting instructions below. Wiring General SANYO is part of the Panasonic Group and is Module Wiring in charge of the manufacturing process for Array Wiring ®... - Page 2 Edition Revision Date Revised Item Revised Content New Edition 2016.2.10 Edition 2016.3.17 Name change ・Change from connection box to connection devices ・Change from ambient to operating Edition 2016.4.20 Changing installation condition ・Clearance between the roof surface and the module...
-
Page 3: Safety Precautions
GENERAL SAFETY cable fixing holes mounting installing or using your Panasonic PV modules. Follow permissions, installation structure. This section contains important electrical and inspection requirements. Do not stand or step on modules. Do not mechanical specifications. -
Page 4: Grounding
Installation (reference) module. This also allows any condensation moisture dissipate. required clearance between the roof surface and the module is more than 4 inch. Solar Module Panasonic recommends installation method mounting profile shown Mid Clamp Figure 1 (2 places) ... -
Page 5: Operating Conditions :5
Panasonic does not provide a warranty for factored according to the lowest recorded Do not connect modules in parallel without clamps. module warranty Panasonic operating temperature recorded using connection devices that connect to provides shall be voided if clamps selected location where the modules will be installed. -
Page 6: Grounding Locations :6
Junction Box Ground wires must be connected to the module’s metal frame at one of these locations. Lay-in lugs or grounding clips can be used to ground Panasonic PV modules. Both Backside methods explained below, please choose one. -
Page 7: Module Terminations :7
1.7 and 2.2 Nm. purchased separately. The return of any modules will not be Insert the wire into the wire slot. Press Conduit accepted by Panasonic unless prior written down on both ends of the wire. applications where wire raceways authorization has been given by Panasonic. -
Page 8: Disclaimer Of Liability
The return of any modules will not be accepted by Panasonic unless prior written authorization has been given by Panasonic. As part of Panasonic’s policy of continuous improvement, Panasonic reserves the right to change product specifications at any time without prior notice. - Page 9 Figure 3.2 (Method 1) Glass Grounding method using bolt and nut Backsheet Frame (Longer side) Note: Use the ground holes illustrated in Figure 3.1. Nut (Stainless steel) Flat washer (Stainless steel) *If using a brass cup washer, a flat Star washer (Stainless steel) washer must be inserted between the Grounding hole cup washer and module frame, and the...
- Page 10 Figure 3.4 Grounding method Glass Frame (Longer side) Using Grounding Clip with bolt and nut Backsheet Note: Use the ground holes illustrated in Figure 3.1. Grounding Clip Assemblies: Tyco Grounding hole Electronics 1954381-2 (0.205” diameter (5.2mm)) 8-32 Screw (Stainless steel) Length (not less than 0.63’‘(16 mm) not more than 0.78’‘(20 mm))
- Page 11 SPECIFICATIONS Electrical Specifications Model VBHN330SA16 VBHN325SA16 VBHN330SA16B VBHN325SA16B Cell Number in Series Rated Power, Watts (Pmax) Maximum Power Voltage (Vpm) 58.0 57.6 Maximum Power Current (Ipm) 5.70 5.65 Open Circuit Voltage (Voc) 69.7 69.6 Short Circuit Current (Isc) 6.07 6.03...