Yaesu FT-897 Operating Manual page 61

MENU MODE No •061 [ MTR ATX SEL ]
Function: Selects the meter display configuration while the
transceiver is transmitting.
Available Values: PWR, ALC, MOD, SWR, VLT, N/A, OFF
Default: PWR
PWR: Indicates the relative transmit power.
ALC: Indicates the relative Automatic Level Control voltage.
MOD: Indicates the deviation level.
SWR: I n d i c a t e s t h e S t a n d i n g Wa v e R a t i o
(forward:reflected).
VLT: Indicates the battery voltage.
N/A: Not available at this time.
OFF: Disables the meter.
MENU MODE No- 062 [ MTR PEAK HOLD ]
Function: Enabling/disabling of the "peak hold" function
of the meter.
Available Values: OFF/ON
Default: ON
MENU MODE No- 063 [ NB LEVEL ]
Function: Setting of the blanking level for the IF Noise
Blanker.
Available Values: 0 ~ 100
Default: 50
MENU MODE No •064 [ OP FILTER 1 ]
Not available at this time.
MENU MODE No •065 [ PG A ]
Function: Programming the [A] key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: MONI
MENU MODE No •066 [ PG B ]
Function: Programming the [B] key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: Q.SPL
MENU MODE No•067 [ PG C ]
Function: Programming the [C] key (in the Operating Func-
tion Row 17) function.
Available Values: All Multi Function , all Menu Item,
MONI, Q.SPL, TCALL, ATC and USER.
Default: ATC
MENU MODE No•068 [ PG ACC ]
Not available at this time.
MENU MODE No •069 [ PG P1 ]
Not available at this time.
MENU MODE No •070 [ PG P2 ]
Not available at this time.
FT-897 O M
PERATING ANUAL
M
ENU
MENU MODE No •071 [ PKT1200 ]
Function: Adjusts the audio input level from the TNC dur-
ing 1200 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
MENU MODE No •072 [ PKT9600 ]
Function: Adjusts the audio input level from the TNC dur-
ing 9600 bps Packet operation.
Available Values: 0 ~ 100
Default: 50
MENU MODE No •073 [ PKT RATE ]
Function: Sets the transceiver's circuitry for the Packet baud
rate to be used.
Available Values: 1200/9600 (bps)
Default: 1200 (bps)
MENU MODE No- 074 [ PROC LEVEL ]
Function: Sets the compression level for the AF speech pro-
cessor in the SSB/AM modes.
Available Values: 0 ~ 100
Default: 50
MENU MODE No- 075 [ RF POWER SET ]
Function: Setting of the maximum power level for the cur-
rent band.
Available Values: 5 ~ 100
Default: 100
MENU MODE No- 076 [ RPT SHIFT ]
Function: Sets the magnitude of the repeater shift.
Available Values: 0.00 ~ 99.99 (MHz)
Default: Depends on operating band and transceiver ver-
sion.
MENU MODE No •077 [ SCAN MODE ]
Function: Selects the desired Scan-Resume mode.
Available Values: TIME/BUSY/STOP
Default: TIME
This Menu Item allows you to select your favorite method
of scan-restart after the scanner has stopped on an incoming
signal (when the squelch opens).
TIME: The scanner will hold for a fixed length of time, set
via MENU MODE No-078 [ SCAN RESUME ] , then
resume whether or not the other station is still trans-
mitting.
BUSY: The scanner will hold until the signal disappears, then
will resume after one second.
STOP: The scanner will stop when a signal is received, and
will not restart.
MENU MODE No •078 [ SCAN RESUME ]
Function: Sets the delay time for scanning resumption.
Available Values: 1 ~ 10 (sec)
Default: 5
MENU MODE No•079 [ SPLIT TONE ]
Function: Enables/disables split CTCSS/DCS cording.
Available Values: OFF/ON
Default: OFF
O
PERATION
Page 59