SERVICE MANUAL CHASSIS MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO. KV-ES29M31 RM-916 SCC-P29A-A KV-ES29M61 RM-916 Singapore SCC-P30A-A TRINITRON COLOR TV ® http://cxema.ru...
Page 2
CARBON PAINTED ON THE CRT, AFTER REMOVING THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE ANODE. THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 –...
Page 3
KV-ES29M31/ES29M61 RM-916 TABLE OF CONTENTS Section Title Page Section Title Page SELF DIAGNOSIS FUNCTION 6. DIAGRAMS ........ 4 6-1. Block Diagram ............63 1. GENERAL ................ 8 6-2. Frame Schematic Diagram ........81 6-3. Circuit Boards Location .......... 84 2. DISASSEMBLY 6-4.
Page 4
KV-ES29M31/ES29M61 RM-916 SELF DIAGNOSTIC FUNCTION The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically begin to flash. The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference.
Page 5
KV-ES29M31/ES29M61 RM-916 DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT 2 times 3 times Lamp ON 0.3 sec. Lamp OFF 3 sec. Lamp OFF 0.3 sec. 4 times 5 times 6 times 7 times STANDBY/SLEEP lamp Diagnostic Item Flash Count* +B overcurrent...
Page 6
KV-ES29M31/ES29M61 RM-916 SELF-DIAGNOSTIC SCREEN DISPLAY For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it is possible to bring up past occurances of failure for confirmation on the screen: [To Bring Up Screen Test] In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below: [Screen display] / channel [5] / Sound volume [-] / Power ON...
Page 7
KV-ES29M31/ES29M61 RM-916 SELF-DIAGNOSTIC CIRCUIT IC4301 IC001 IC003 RGB JUNGLE OVP OCP SYSTEM MEMORY FROM IKIN CRT (IK) [H] IC6801 XRAY [V] D6806/D6801 V PROT CXA2100Q IC004 MEMORY [+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q6610 and Q6609.
KV-ES29M31/ES29M61 SECTION 3 RM-916 SERVICE JIG 3-1. JIGS REQUIRED FOR SERVICING REF NO. DESCRIPTION PART NO. REMARK TOOL (20P), SERVICE 3-702-763-01 For A to V board extension TOOL (40P), SERVICE 3-702-764-01 For A to E board extension TOOL (50P-A), SERVICE...
Page 41
KV-ES29M31/ES29M61 SECTION 4 RM-916 SET-UP ADJUSTMENTS • The following adjustments should be made when a complete Perform the adjustments in the following order : realignment is required or a new picture tube is installed. 1. Beam Landing • These adjustments should be performed with rated power 2.
Page 42
KV-ES29M31/ES29M61 RM-916 4-2. CONVERGENCE ADJUSTMENT V. STAT Preparation : • Before starting this adjustment, adjust the focus, horizontal size and vertical size. • Set the PICTURE 70% and BRIGHTNESS 0%. • Cross hatch / Dot pattern. (1) Horizontal and Vertical Static Convergence H.
Page 43
KV-ES29M31/ES29M61 RM-916 BMC (Hexapole) Magnet. (2) Dynamic Convergence Adjustment If the red, green and blue dots are not balanced or aligned, then Preparation: • use the BMC magnet to adjust in the manner described below. Before starting this adjustment, adjust the horizontal static convergence and the vertical static convergence •...
Page 44
KV-ES29M31/ES29M61 RM-916 (3) Screen-corner Convergence 4-3. FOCUS ADJUSTMENT Note Focus adjustment should be completed before W/B adjustment. (1) Receive digital monoscope pattern. (2) Set "A/V CONTROL" to "STANDARD". a-d : screen-corner (3) Adjust FOCUS VR so that the center of the screen becomes misconvergence justfocus.
Page 45
KV-ES29M31/ES29M61 RM-916 3. SUB PICTURE BRIGHTNESS ADJUSTMENT 4-5. G2 (SCREEN) AND WHITE BALANCE 1) Tune RF PAL white signal at program No. 1 and No. 2. ADJUSTMENTS 2) Select “TWIN PICTURE” mode. 3) Receive different RF PAL white signals in MAIN and Sub 1.
KV-ES29M31/ES29M61 SECTION 5 RM-916 CIRCUIT ADJUSTMENTS 5-1. ADJUSTMENTS WITH COMMANDER Service adjustments are made with the RM-916 that comes with 1, 4 this unit. Select the adjustment item. ↓ a. ENTERING SERVICE MODE 3, 6 Raise/lower the data value. With the unit on standby ↓...
Page 47
KV-ES29M31/ES29M61 RM-916 5-2. ADJUSTMENT METHOD Item Number 00 of device GEO Use the same method for all Items. Use 1 and 4 to select the This explanation uses H-Position as an example. 1. Select “GEO 00 VSZ” with the 1 and 4 buttons.
Page 57
KV-ES29M31/ES29M61 RM-916 NOTE • shaded items are fixed data. • Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode. • Note for Different Data: Those are the standard data values written on the microprocessor. Therefore, the data values of the modes and stored respectively in the memory.
Page 58
KV-ES29M31/ES29M61 RM-916 5-3. PICTURE QUALITY ADJUSTMENTS 1. NTSC VIDEO INPUT SUB COLOR ADJUSTMENT (SCL) Input signal ; NTSC color bar, 75% to Video 1. [TWIN] mode, [Service] mode. 1. Set to service mode. 2. Input RF PAL colorbar signal. (i) SUB CONTRAST Set A/V control to PERSONAL.
Page 59
KV-ES29M31/ES29M61 RM-916 2. NTSC RF INPUT 3. PAL VIDEO INPUT Input signal ; NTSC RF color bar, 75%. Input signal ; PAL color bar, 75% to Video 1. [TWIN] mode, [Service] mode. [TWIN] mode, [Service] mode. (i) SUB CONTRAST (i) SUB CONTRAST...
Page 60
KV-ES29M31/ES29M61 RM-916 3. PAL RF INPUT 5-4. DEFLECTION ADJUSTMENTS Input signal ; PAL RF color bar, 75%. FOR DRC 1250 [TWIN] mode, [Service] mode. 1. Set to Service Mode. 2. Input a Pal cross hatch/dot signal. (i) SUB CONTRAST 3. Set the following condition.
Page 61
KV-ES29M31/ES29M61 RM-916 FOR DRC 100 MODE 5-5. A BOARD ADJUSTMENT AFTER IC003 12. Set to DRC 100 mode. (MEMORY) REPLACEMENT 13. Repeat Step 5, Step 6 and Step 7. 14. Write “DAC 00 HCT DRC 100 Mode” as “DAC 00 HCT DRC When replacing IC003 and IC004 (MEMORY), be sure to change 1250 Mode”...
KV-ES29M31/ES29M61 SECTION 7 RM-916 EXPLODED VIEWS NOTE: • • Items marked " ∗ " are not stocked since Items with no part number and no The components identified by description are not stocked because they are seldom required for routine...
Page 102
4-071-305-01 BUTTON, POWER * A-1299-108-A A BOARD COMPLETE (KV-ES29M61) * A-1394-965-A J BOARD COMPLETE * A-1299-158-A A BOARD COMPLETE (KV-ES29M31) * A-1136-069-A BC4 BOARD COMPLETE * A-1136-054-A B3 BOARD COMPLETE * A-1241-403-A F2 BOARD MOUNT * A-1343-743-A E BOARD MOUNT...
Page 105
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C1275 1-163-007-11 CERAMIC CHIP 680PF CN1116 1-695-915-11 TAB (CONTACT)
Page 106
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <IC> <TRANSISTOR> IC001 8-752-910-26 IC CXP750096-012Q Q001 8-729-026-49...
Page 107
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R041 1-216-025-91 RES,CHIP 1/10W R101 1-216-025-91 RES,CHIP 1/10W...
Page 108
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R1283 1-216-295-91 SHORT C8108 1-164-004-11 CERAMIC CHIP 0.1MF...
Page 109
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C8209 1-163-251-11 CERAMIC CHIP 100PF <COIL> C8210 1-163-251-11...
Page 110
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R8173 1-216-025-91 RES,CHIP 1/10W C361 1-124-779-00 ELECT CHIP...
Page 111
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C609 1-163-021-91 CERAMIC CHIP 0.01MF C823 1-163-021-91 CERAMIC CHIP 0.01MF...
Page 112
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <FILTER> <COIL> FL304 1-234-177-21 FILTER, CHIP EMI L302...
Page 113
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R313 1-216-009-91 RES,CHIP 1/10W R557 1-216-049-91 RES,CHIP 1/10W...
Page 114
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R640 1-216-009-91 RES,CHIP 1/10W R816 1-216-073-00 RES,CHIP 1/10W...
Page 115
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R888 1-216-009-91 RES,CHIP 1/10W R979 1-216-295-91 SHORT R889...
Page 116
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK RB026 1-239-409-11 NETWORK RESISTOR (CHIP) 47 C2052 1-163-133-00...
Page 117
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <IC> R2044 1-216-057-00 RES,CHIP 2.2K 1/10W R2046 1-216-075-00...
Page 118
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. BC4 C REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <CRYSTAL> D9007 8-719-051-85 DIODE HSS83TD D9008...
Page 119
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R9042 1-216-049-91 RES,CHIP 1/10W C6618 1-163-021-91 CERAMIC CHIP 0.01MF...
Page 120
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C6808 1-106-228-00 MYLAR 0.22MF 100V C6874 1-136-165-00 MYLAR 0.1MF...
Page 121
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK D6616 8-719-911-55 DIODE U05G IC6603 8-749-016-66 IC MCR5152...
Page 122
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <IC LINK> R6609 1-215-489-00 METAL 680K 1/4W R6610...
Page 123
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R6667 1-249-413-11 CARBON 1/4W R6832 1-215-477-00 METAL 220K...
Page 124
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R6896 1-216-089-91 RES,CHIP 1/10W C6114 1-107-909-11 ELECT 47MF...
Page 125
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <DIODE> <IC LINK> D6101 8-719-510-02 DIODE D1NS4 PS6101...
Page 126
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R6134 1-208-806-11 METAL CHIP 0.50% 1/10W R6216 1-216-065-91 RES,CHIP 4.7K...
Page 127
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <NEON LAMP> C4354 1-107-823-11 CERAMIC CHIP 0.47MF C4355...
Page 128
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK D4804 8-719-911-19 DIODE 1SS119-25 Q4801 8-729-230-49 TRANSISTOR 2SC2712-YG...
Page 129
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R4339 1-216-051-00 RES,CHIP 1.2K 1/10W R4803 1-216-049-91 RES,CHIP...
Page 130
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R4864 1-208-788-11 METAL CHIP 1.8K 0.50% 1/10W * A-1241-402-A F1 BOARD MOUNT...
Page 131
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <SWITCH> <CONNECTOR> S1651 ! 1-571-433-21 CN1932* 1-564-509-11 PLUG, CONNECTOR 6P...
Page 132
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK S1975 1-572-198-11 SWITCH, KEYBOARD C8333 1-115-340-11 CERAMIC CHIP 0.22MF...
Page 133
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C8412 1-164-004-11 CERAMIC CHIP 0.1MF D8309 8-719-158-35 DIODE RD9.1SB...
Page 134
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK <CHIP CONDUCTOR> Q8360 1-801-806-11 TRANSISTOR DTC144EKA-T146 Q8361 8-729-230-49...
Page 135
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R8343 1-216-065-91 RES,CHIP 4.7K 1/10W R8412 1-216-073-00 RES,CHIP...
Page 136
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK R8565 1-216-049-91 RES,CHIP 1/10W R8472 1-216-089-91 RES,CHIP 1/10W...
Page 137
KV-ES29M31/ES29M61 RM-916 The components identified by shading and mark ! are critical for safety. Replace only with part number specified. REF. NO. PART NO. DESCRIPTION REMARK REF. NO. PART NO. DESCRIPTION REMARK C1827 1-104-666-11 ELECT 220MF C1828 1-163-021-91 CERAMIC CHIP 0.01MF...