JVC CH-X1500 Service Manual page 24

CH-X1500
3.2.2 CH-X1500 Error code
The following error codes can be displayed and stored in up to 3 memories when the KD-MX3000 is used with the controller. Refer
QQ
3 7 63 1515 0
to the KD-MX3000 service manual regarding error code indication.
The error code indication when using the earlier controller is the same as the CH-X99,KD-MK88 and other 12CD changer models.
Generating condition
Tray extension error Tray-in switch time out
(Tray-in switch Low Tray-out switch High)
Tray-out switch time out
(Tray-in switch High Tray-out switch High)
Tray-in switch time out
(Tray-in switch Low Tray-out switch Low)
MAG-in switch Low to High
Tray retraction error Tray-in switch time out
(Tray-in switch Low Tray-out switch Low)
Tray-out switch time out
(Tray-in switch High Tray-out switch High)
Tray-in switch time out
(Tray-in switch Low Tray-out switch Low)
MAG-in switch Low to High
Lifter raise error Wait position time out
Wait position time out
Wait position time out
Lifter lower error Wait position time out
Wait position time out
Wait position time out
Chuck error Play position time out
TE
L 13942296513
Play position time out
Play position time out
Unchuck error Wait position time out
Wait position time out
Wait position time out
Eject error Eject position time out
Eject position time out
MAG in switch time out
Initialize error Mechanism switch time out
Absolute position time out
Note:
The 1st error code is indicated by E1, while the 2nd and 3rd error codes are respectively indicated by E2 and E3.
www
1-24
http://www.xiaoyu163.com
CH-1 error code table
x ao
y
. i
http://www.xiaoyu163.com
8
Description
Tray stops part way
Tray stops part way
Tray-in switch faulty or other defect
Magazine removed when tray partly extende
Tray motor inoperative
Tray retraction stops part way
Tray-in switch faulty or other defect
Magazine removed when tray partly retracted
Position motor inoperative
Position not stable in fine adjust mode
Other fault
Position motor inoperative
Position not stable in fine adjust mode
Other fault
Q Q
Position motor inoperative
3 6 7 1 3
Position not stable in fine adjust mode
Other fault
Position motor inoperative
Position not stable in fine adjust mode
Other fault
Position motor inoperative
Eject position not attained
Magazine not ejected
Both Tray-in and Tray-out Low
Not stable at absolute position
u163
.
2 9 9 4 2 8
Error code
E1 03 00 11
E1 03 00 12
E1 03 00 13
E1 03 00 14
E1 03 00 16
E1 03 00 17
E1 03 00 18
E1 03 00 19
E1 02 00 21
E1 02 00 22
E1 02 00 23
E1 02 00 26
E1 02 00 27
E1 02 00 28
E1 02 00 31
1 5 0 5 8 2 9 9 4
E1 02 00 32
E1 02 00 33
E1 02 00 36
E1 02 00 37
E1 02 00 38
E1 02 00 41
E1 02 00 42
E1 02 00 43
E1 03 00 46
E1 03 00 47
m
co
9 9
2 8 9 9