Advertisement
Quick Links
PART NUMBERS:
0000-8F-Z20 DOCKABLE DVD KIT
0000-8F-N11 DVD INSTALL KIT
DVD KIT CONTENTS
DVD PLAYER
110 VOLT ADAPTER
0000-8F-Z22
USER'S
MANUAL
REMOTE
0000-8F-Z24
0000 8F Z19
WIRELESS GAME
CONTROLLER
0000 8F Z23
TOOLS REQUIRED
PROTECTIVE CLOTH
CORDLESS DRILL
DRILL STOP
8 mm DRILL BIT
FIBER STICK
FELT MARKER
T-10 TORX BIT
#3 PHILLIPS SCREWDRIVER
UTILITY KNIFE
TORQUE WRENCH
SAFETY GLASSES
RUBBER MALLET
DEBURRING TOOL
FISH WIRE
7mm SOCKET OR NUT RUNNER
1/14/08
GENUINE ACCESSORIES
INSTALLATION INSTRUCTIONS
DOCKABLE DVD KIT
0000-8F-Z25
QUICK REF.
CARD
MODULATOR
0000-8F-N24
WIRELESS
HEADPHONES
0000 8F N16
DVD INSTALL KIT CONTENTS
TRIM BEZEL
0000 8F N12
FM MODULATOR
FM
0000 8F N22
TEMPLATE
(Not to scale)
0000 8F N23
0000 8F Z21
HARDWARE KIT CONTENTS
(2)
FLANGE NUTS
(4)
TRIM BEZEL TORX SCREWS
(2)
PHILLIPS HEAD SCREWS
(6)
FRAME MOUNTING NUTS
(11) TIE WRAPS
(1)
FOAM PAD
(2)
FOAM TAPE
ADDITIONAL ACCESSORIES AVAILABLE
DVD PLAYER BATTERY
DVD PLAYER CARRY CASE 0000 8F Z26
1
APPLICABLE MODELS:
INSTALLATION
WIRE
INSTRUCTIONS
HARNESS
0000 8F N13
WIRES
DOCKING
HARDWARE KIT
STATION
0000 8F N17
2007 > CX9
WITH MOONROOF
MOUNTING
BRACKET
0000 8F N15
(See below)
0000 8F Z27
Advertisement
Related Manuals for Mazda 0000-8F-Z20
Summary of Contents for Mazda 0000-8F-Z20
-
Page 1: Tools Required
GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS PART NUMBERS: APPLICABLE MODELS: 0000-8F-Z20 DOCKABLE DVD KIT 2007 > CX9 DOCKABLE DVD KIT 0000-8F-N11 DVD INSTALL KIT WITH MOONROOF DVD KIT CONTENTS DVD INSTALL KIT CONTENTS INSTALLATION DVD PLAYER 110 VOLT ADAPTER WIRE INSTRUCTIONS 0000-8F-Z22... -
Page 2: Installation Instructions
Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored. • If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. - Page 3 WIRING UNDER THE HEADLINER FOAM TAPE DVD WIRING MOONROOF OPENING OEM WIRING CUTOUT 1/14/08...
- Page 4 0). BEFORE STARTING 1.) OBTAIN ONE DVD INSTALL KIT 0000 8F N11 FOR EACH VEHICLE. 2.) REVIEW THE INSTRUCTIONS COMPLETELY BEFORE STARTING. 3.) RECORD RADIO PRESETS ON THE "INSPECTION PAGE" AT THE END OF THESE INSTRUCTIONS. (A.M. / F.M. / SATELLITE / TRIP COMPUTER AS APPLICABLE). 4.) CLOSE THE MOONROOF 5.) PLACE THE SHIFTER IN "D"...
- Page 5 1.) MARKING AND CUTTING THE HE ADLINER 1.) USING A FIBER STICK CAREFULLY REMOVE THE HEADLINER PUSHPIN LOCATED BEHIND THE CENTER DOMELIGHT. 2.) ALIGN THE TEMPLATE ON THE CENTER DOME LIGHT AND REINSTALL THE PUSHPIN TO HOLD THE TEMPLATE IN PLACE. NOTE: WHEN PROPERLY ALIGNED, THE FORWARD EDGE OF THE TEMPLATE WILL BE AT THE MOONROOF OPENING AND THE TEMPLATE 'WING' WILL FOLLOW THE...
- Page 6 5.) CAREFULLY REMOVE THE FOAM BLOCK FROM THE ROOF BOW. SAVE IT FOR A LATER STEP. 6.) MOVE TO AN APPROPRIATE, FLAT WORK SURFACE. CUT A 2.5 cm (1") STRIP FROM THE LONG SIDE OF THE REMOVED SECTION OF HEADLINER. THIS STRIP WILL BE USED AS A SPACER LATER IN THE INSTALLATION.
- Page 7 2.) INSTALLING THE BRACKET NOTE: REFERENCE THE DETAIL VIEW OF THE INSTALLED BRACKET. THE VIEW IS SHOWN FROM ABOVE THE HEADLINER TO ILLUSTRATE THE (4) BRACKET TABS ENGAGING THE REAR ROOF BOW SLOTS AND THE LOCATION OF THE (2) FLANGE NUTS. FRONT OF VEHICLE REAR OF VEHICLE 1.) INSTALL THE BRACKET SO THE TABS ENGAGE THE...
- Page 8 2.) ALIGN THE LEFT BRACKET HOLE TO THE EXISTING ROOF BOW HOLE. INSTALL A SCREW AND FLANGE NUT FROM THE KIT. LOOSELY TIGHTEN THE BOLT USING A #3 PHILLIPS SCREWDRIVER. CAUTION: ENSURE THE SUNSHADE IS CLOSED BEFORE DRILLING - TO PREVENT DAMAGE. CAUTION: USE A DRILL STOP TO PREVENT DAMAGE TO THE ROOF SHEET METAL.
- Page 9 3). REMOVING COMPONENTS - TRIM 1.) USE A PICK TOOL TO OPEN THE COVER AT THE POINTS INDICATED. 2.) REMOVE THE SCREW FROM THE SUNVISOR SWIVEL ARM. DETACH ANY ELECTRICAL CONNECTORS AND REMOVE THE SUNVISOR. 3.) REMOVE THE OVERHEAD MAP LIGHT 1.) USE A FIBER STICK TO REMOVE THE LENSES.
- Page 10 5.) REMOVE THE "A" PILLAR TRIM a.) PULL THE TOP PORTION UNTIL THE PUSH PIN EXTENDS APPROXIMATELY 12mm (1/2 "). b.) SLIDE THE TRIM UPWARD UNTIL IT DETACHES FROM THE PUSH PIN. c.) PULL FIRMLY INWARD TO DETACH THE TRIM FROM THE REMAINING CLIPS.
- Page 11 9.) UNSCREW THE PLASTIC CAP AND REMOVE THE DRIVERS KICK PLATE. NOTE: USE CARE TO PREVENT DAMAGE AND SCRATCHES TO THE TRIM AND INTERIOR. PLACE PARTS ON A PROTECTED SURFACE AFTER REMOVAL. 1/14/08...
- Page 12 10). REMOVE BOTH DECORATION PANELS BY PULLING STRAIGHT AWAY. 11). REMOVE THE CENTER PANEL SCREWS, PULL FORWARD, DISCONNECT ANY ELECTRICAL CONNECTORS AND REMOVE THE PANEL. 12.) REMOVE (4) SCREWS, DISCONNECT ELECTRICAL CONNECTIONS AND REMOVE THE RADIO. (Non-Navigation Head Unit shown). ...
- Page 13 14). REMOVE THE DRIVER SIDE CONSOLE AND INSTRUMENT PANEL SIDE WALLS. 15). REMOVE THE HOOD RELEASE LEVER BY RELEASING THE CENTER TOP TANG. REMOVE THE HOOD RELEASE HANDLE SCREW. NOTE: RECORD OR OTHERWISE NOTE THE COLORS AND LOCATION OF CONNECTORS BEHIND THE LOWER PANEL TO ENSURE CORRECT RE- INSTALLATION.
- Page 14 4.) INSTALL ING WIRING 1.) ROUTE A WIRE PULLING TOOL FROM THE MOONROOF OPENING TO THE DRIVER SIDE "A" PILLAR. CAUTION: USE CARE DO NOT WRINKLE THE HEADLINER. 2. TAPE THE BLACK CONNECTOR OF THE DVD HARNESS TO THE TOOL. 3.) PULL THE WIRING TO THE CORNER OF THE MOONROOF OPENING.
- Page 15 5. ROUTE THE WIRING FROM THE MOONROOF OPENING, ABOVE THE HEADLINER TO THE DVD CUTOUT. 6. TUCK THE WIRING ABOVE THE HEADLINER AS SHOWN. THE BLACK CONNECTOR SHOULD END APPROXIMATELY 2/3 OF THE WAY ACROSS THE DVD OPENING. 7.) PLACE THE PREVIOUSLY CUT (2.5 cm / 1") FOAM STRIP AS A SPACER BETWEEN THE HEADLINER AND FRONT OF THE BRACKET.
- Page 16 9.) REACH ABOVE THE HEADLINER AND PLACE A PIECE OF FOAM TAPE TO ADHERE THE DVD WIRING TO THE HEADLINER. THE TAPE WILL HOLD THE WIRING IN POSITION AS AN ASSEMBLY AID. CAUTION: ENSURE THE WIRING IS INBOARD OF THE SIDE CURTAIN AIRBAG.
- Page 17 13.) ROUTE THE DVD HARNESS UNDER THE STEERING COLUMN AND BEHIND THE IP BRACE. ATTACH IT TO THE ADJACENT HARNESS WITH A TIE WRAP. STEERING COLUMN 14.) ATTACH THE GREY CONNECTOR OF THE DVD HARNESS TO THE FM MODULATOR 15.) PEEL AND STICK THE FOAM PAD TO THE UN- LABELED SIDE OF THE FM MODULATOR 16.) CONNECT THE CABLES TO THE FM MODULATOR.
- Page 18 18.) LOCATE THE ACCESSORY POWER SOCKET AT THE LOWER RIGHT CORNER OF THE CENTER STACK. REMOVE THE ADJOINING COIN TRAY TO EXPOSE THE CONNECTOR. 19.) ROUTE THE 12v POWER CONNECTORS IN FRONT OF THE CENTER STACK FRAME TOWARD THE COIN SLOT OPENING. 20.) DISCONNECT THE FRONT ACCESSORY SOCKET FROM FROM ITS RECEPTACLE AND CONNECT IT TO THE MAIN DVD HARNESS.
- Page 19 21.) USE FOAM TAPE TO WRAP THE MAIN DVD HARNESS CONNECTOR, CAPTURING THE EXCESS WIRE UNDER THE FOAM TO PREVENT RATTLE. 22.) PUSH THE FOAM WRAPPED CONNECTOR INTO THE OPENING DIRECTLY BEHIND THE COIN TRAY. MAKE SURE IT REMAINS BEHIND THE CENTER STACK FRAME.
- Page 20 5.) INSTALLING DVD COMPONENTS 1.) PLACE THE DVD FRAME OVER THE BRACKET STUDS AND INSTALL 6 NUTS. TORQUE TO 25.5 kg-cm (22.1 in-lbs). NOTE: THE INFRARED DIODES FACE THE REAR OF THE VEHICLE. ENSURE THE WIRING ON THE DVD FRAME REMAINS WITHIN THE CHANNEL ON THE DVD FRAME TO AVOID PINCHING WIRES.
- Page 21 1.) PUSH THE COVER PLATE UP AND BEGIN TO INSERT THE DVD PLAYER. 2.) SLIDE THE DOCKING LOCK TO THE RIGHT (UNLOCKED POSITION) AND FINISH INSERTING THE DVD PLAYER. THE PLAYER WILL LOCK IN PLACE. PUSH UP ON THE REAR CORNERS OF THE PLAYER TO CONFIRM ENGAGEMENT.
-
Page 22: Testing The System
3. Lift up the power window switch to fully close the windows, and keep it pulled up for approximately 2 seconds. 4. Position the engine switch OFF and then ON again. If the function doesn't work after these procedures, please contact your Mazda dealer When the battery is disconnected, the DSC will stop operating. - Page 23 INSPECTION • Inspect installed/reinstalled parts for the following items. Inspections may differ depending on vehicle. Inspection Items (○ ) Installation/ Scratches/ Dirt/ Operation Inspection Parts Clearance/Fit Tightening/ Harness check Engagement interference DVD player ○ ○ ○ ○ *1 Audio unit ○...
-
Page 24: Troubleshooting
TROUBLESHOOTING CONDITION POSSIBLE CAUSE Unit will not power up. DVD player not receiving power. DVD player not grounded properly. Blown fuse. Short in vehicle power. Power and Ground backward. Fuse keeps blowing. Short in DVD player. No Sound from radio Antenna circuit at fault.