Table of Contents
Advertisement
Quick Links
GENUINE SATELLITE RADIO KIT
INSTALLATION INSTRUCTIONS
Thank you for purchasing a genuine Mazda accessory.
Before removal and installation, be sure to thoroughly read these instructions.
Please read the contents of this booklet in order to properly install and use the satellite
radio kit. Your safety depends on it.
Keep these instructions with your vehicle records for future reference.
x There are several
safety when installing. Always read and follow them in order to prevent injuries,
accidents, and possible damage to the vehicle.
WARNING: Indicates a situation in which serious injury or death could result if the
warning is ignored.
CAUTION:
Indicates a situation in which bodily injury or damage to the vehicle
could result if the caution is ignored.
x If in any doubt, please ask your Mazda dealer to install the accessory in order to
prevent errors in installation.
x If you have any questions about the use of the accessory, ask your Mazda dealer for
proper advice before using it.
x Mazda and its suppliers are not responsible for injuries, accidents, and damage to
persons and property that arise from the failure of the dealer or installer to follow these
instructions.
x
To ensure safety and reliability of the work, installation, removal and disposal work
done by an Authorized Mazda Dealership is recommended.
x
Be careful not to lose removed parts, and be sure that they are kept free from
scratches, grease or other dirt.
PART NAME:
PART NUMBER:
VEHICLE:
NOTE
To the dealer
x Please turn over these instructions to the customer after installation.
To the customer
x Keep these instructions after installation. The instructions may be necessary for
installing other optional parts or removal of this accessory.
x
Should the vehicle or this accessory be resold, always leave these instructions
with it for the next owner.
WARNING
WARNING and
CAUTION sections in this booklet concerning
SATELLITE RADIO KIT
0000 81 K11 (harness Kit G-X)
MAZDA RX-8
(Applicable to 2010 model year vehicles and after)
Mazda RX-8 1
1ED6P11A23900
Advertisement
Table of Contents
Related Manuals for Mazda 0000 81 K11
Summary of Contents for Mazda 0000 81 K11
-
Page 1: Installation Instructions
Indicates a situation in which bodily injury or damage to the vehicle could result if the caution is ignored. x If in any doubt, please ask your Mazda dealer to install the accessory in order to prevent errors in installation. -
Page 2: Installation View
Harness (G-X) To AUX connector To Audio unit Tie redundant part iPod connection cable Tie redundant part (GND) SIRIUS only Electro tap (+B and ACC) Harness (G-X) To AUX connector To Audio unit Tie redundant part Mazda RX-8 2... -
Page 3: Connection Diagram
16-pin connector 8-pin connector (Gray) 16-pin connector DLP unit (SIRIUS) Antenna cable CAUTION x When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle. Mazda RX-8 3... - Page 4 8-pin connector 16-pin connector (Gray) 16-pin connector DLP unit (SIRIUS) Antenna cable CAUTION x When connecting a connector, be sure to insert it straight along the guide. The connector terminal may be bent if inserted at an angle. Mazda RX-8 4...
-
Page 5: Before Installation
Part Part name Qty. Part Part name Qty. Part Part name Qty. Antenna DLP unit Alcohol wipe Harness Kit G-X (0000 81 K11) Part Part name Qty. Part Part name Qty. Part Part name Qty. Double-sided Harness (G-X) Pad protector... - Page 6 20 {0.78} mm {in} NOTE x When the negative battery cable is removed, the clock, radio, trip meters and other memories will be erased. Before performing work, record the content of the memory. Mazda RX-8 6...
-
Page 7: Battery Cover Removal
2. While pushing the lower panel downward, disengage hooks B (2) and remove the lower panel. Hooks B Vehicle front 3. Remove the screws (4), then remove the knee bolster. Screws Screws (If equipped) Knee bolster Vehicle front Mazda RX-8 7... - Page 8 3. Pull up the speaker grille in the direction of the arrow (4) and disengage the speaker grille clips A (6). 4. Pull out the speaker grille from the fulcrum point of each Tabs B Vehicle front tab B. < Speaker grille removal note> Press Speaker grille Pull Mazda RX-8 8...
-
Page 9: Glove Compartment Removal
Glove compartment Clip Inner scuff plate (passenger’s side) removal 1. Pull the inner scuff plate upward, detach clips A from the Inner scuff plate body, and then remove the inner scuff plate. Clip A Vehicle front Mazda RX-8 9... - Page 10 Trunk end trim 1. Remove the fasteners. Vehicle front 2. Pull the trunk end trim upward, then detach clips A, locator pins B, and tabs C. 3. Remove the trunk end trim. Fasteners Fasteners Clip A Locator pin B Mazda RX-8 10...
- Page 11 Rear combination light (driver’s side) removal Nuts (8 mm) 3.9 5.9 N m {40 60 kgf cm, 35 52 in lbf} 1. Disconnect the connector. 2. Remove the screw. 3. Remove the rear combination light. Connector Vehicle front Rear combination light Mazda RX-8 11...
- Page 12 Pad protectors 5. Affix pad protector half to the DLP unit as shown in the DLP unit Pad protector 1/2 figure. CAUTION To ensure proper affixing, be sure to degrease the area where the pad protector is affixed. Mazda RX-8 12...
- Page 13 DLP unit will interfere with the trunk side trim and Side body panel cannot be installed. To ensure proper affixing, be sure to degrease the area where the double-sided adhesive tape is affixed. Align side of DLP unit with Vehicle front line of side body panel Mazda RX-8 13...
-
Page 14: Installing Antenna
Failure to follow this route will not provide the slack required to open and close the trunk lid. Do not remove trunk seam from the flange. The antenna cable must not interfere with the flange Tie wraps (small) seals. Mazda RX-8 14... - Page 15 11. Secure the antenna cable to the vehicle wiring harness with tie wraps (small). 12. Secure the antenna cable to the vehicle wiring harness with tie wraps (small). Vehicle wiring harness Antenna cable Tie wraps (small) Vehicle front Tie wraps (small) Mazda RX-8 15...
- Page 16 Pad protector 1/2 x 1 shown in the figure. iPod integration module CAUTION To ensure proper affixing, be sure to degrease the area where the pad protector is affixed. Pad protectors 1/3 x 3 Pad protectors 1/3 x 3 Mazda RX-8 16...
- Page 17 Vehicle wiring harness clip 6. Secure the tie wrap (large) installed on the iPod integration module to the vehicle wiring harness on iPod integration module Vehicle front the back of the dashboard. Tie wrap (large) Vehicle wiring harness Mazda RX-8 17...
-
Page 18: Installing The Harness
3. Insert and connect the harness (G-X) to the Information Vehicle wiring harness display 12-pin connector. Vehicle front 4. Secure the harness (G-X) to the vehicle wiring harness with tie wrap (small). Tie wrap (small) 100 {3.93} Harness (G-X) Information display 12-pin connector mm {in} Mazda RX-8 18... - Page 19 Make sure the ground eyelet contacts the steel bracket. To AUX connector Pad protector 1/2 10. Bundle the redundant part of harness (G-X) GND wire and secure it to the harness (G-X) using a tie wrap (small). Mazda RX-8 19...
- Page 20 21. Go to Step 16 on page 24. Dashboard Tie wrap (large) Pad protectors Vehicle front Remove connector cover when connecting iPod; fit connector cover when iPod is not used Put iPod connection cable in glove box (Cable 30 cm from instrument panel) Mazda RX-8 20...
- Page 21 3. Insert and connect the harness (G-X) to the Information Vehicle wiring harness display 12-pin connector. Vehicle front 4. Secure the harness (G-X) to the vehicle wiring harness with tie wrap (small). Tie wrap (small) 100 {3.93} Harness (G-X) Information display 12-pin connector mm {in} Mazda RX-8 21...
- Page 22 Make sure the ground eyelet contacts the steel bracket. To AUX connector Pad protector (1/2) 10. Bundle the redundant part of harness (G-X) GND wire and secure it to the harness (G-X) using a tie wrap (small). Mazda RX-8 22...
- Page 23 18. Wrap both looped ends of the excess harness with pad protectors. 19. Push the bundled harness into the back of the dashboard. 20. Go to Step 16 on page 24. Dashboard Tie wrap (large) Pad protectors Mazda RX-8 23...
- Page 24 Install the harness to the clips with care not to damage the clip. 19. Secure the harness (G-X) to the vehicle wiring harness with a tie wrap (large). Vehicle wiring harness Clips (4 locations) Rear harness protector Harness (G-X) Clip Mazda RX-8 24...
- Page 25 Vehicle wiring harness Clips (2 locations) Rear harness protector Harness (G-X) Clip 22. Secure the harness (G-X) to the vehicle wiring harness Tie wraps (large) with tie wraps (large). Vehicle wiring harness Harness (G-X) Vehicle front Tie wraps (large) Mazda RX-8 25...
- Page 26 NOTE Bundle the harness into a loop and attach it to the Vehicle front sheet metal on the interior side of the trunk, and secure with pad protector halves. Harness (G-X) Pad protectors Mazda RX-8 26...
- Page 27 If the TCS/DSC or DSC OFF indicator lights do not go out after turning the ignition switch to the ON position, consult your Mazda dealer. x When the battery is disconnected, the windows will not fully open and close automatically.
- Page 28 Note: Sirius broadcasts can only be received in an open area, enclosed spaces such as garages or work buildings block the satellite reception. To troubleshoot problems, go to the following web page and select “Troubleshooting” in the Satellite https://portal.mazdausa.com/dealershome/service_parts/accy_website Radio section: Date Vehicle. VIN. The term of validity for this sheet: 3 months Mazda RX-8 28...