Page 1
Nemo 240 AD Nemo 275 AD Nemo 300 AD INSTRUCTION MANUAL........1-12 MANUEL D’INSTRUCTION........13-24 ANWEISUNG HANDBUCH........25-36 INSTRUCTIE HANDBOEK........37-48 MANUAL DE INSTRUCCIÓN.......49-60 BRUKSANVISNING..........61-72 www.silvermarine.com...
PVC on both sides, and include a transom and molded floorboard system. This manual has been compiled to help you achieve long term safe use, and pleasure from your Silver Marine®. Please read it carefully and familiarize yourself with the craft before boating.
7. Aft 8. Beam 9. Transom 10. Length overall 11. Starboard side 12. Port side TECHNICAL SPECIFICATIONS MODEL NEMO 240 AD NEMO 275 AD NEMO 300 AD DESIGN CATEGORY TYPE II C, TYPE V C, TYPE V STANDARD NO. EN ISO6185-1:2001...
PARTS TERMINOLOGY 10.HI-QUALITY MATERIALS 10.HI-QUALITY MATERIALS 10.HI-QUALITY MATERIALS 5.OARS WITH 5.OARS WITH 5.OARS WITH OARLOCK SYSTEM OARLOCK SYSTEM OARLOCK SYSTEM 4.RUBBER STRAKING 4.RUBBER STRAKING 4.RUBBER STRAKING 1.D-TOWING RING 1.D-TOWING RING 1.D-TOWING RING 2.BENCH SEAT 2.BENCH SEAT 2.BENCH SEAT 3.SAFETY GRAB 3.SAFETY GRAB 3.SAFETY GRAB HANDLE...
PACKING LIST Boat Hull with Air Deck, Oars, Foot Pump, Pressure Gauge, Wooden Seat, Docking Rope, Grab Safety Handles, 5 Screw Valves + 1 Drain Valve, Repair Kit, Carry Bag, Bench Seat Bag and Boat Cover. INSTALLATION TIPS Tip 1: Make sure to tuck in wood board’s edge to the joint of tubes and bottom. Tip 2: Make sure to press down and turn the pop-up spring valve 90 degrees before inflating.
Make sure the side with wooden boards is placed on the bottom and the air valve of the inflatable keel fits through the hole in the bow. 3. Install Seating Board When the air deck is in position, hook the plastic brackets at the bottom of the plywood bench into the PVC straps on your Silver Marine® boat.
4. Seat bag assembly After the Seat Assembly, attach the bench seat bag onto the bench seat. STEP THREE: FINISH INFLATION After inflating the tubes, insert the barometer against the valve. Check if the pressure in the air chambers reaches 0.25 bars, then remove the barometer and screw the cap on. Note: Gently press down around the air deck floor edges to ensure a snug fit under the buoyancy chambers.
PRESERVATION You should endeavour to keep your Silver Marine® in good condition. Preferably store it deflated. If you leave it outside, raise it off the ground and cover it from the elements especially strong sunshine, or heavy, cold, raining, conditions.
5. Check the inflation valves, clean them and remove any sand or debris. REPAIRING Your Silver Marine® boat comes with a repair kit for patching minor punctures. Most leaks only take a few minutes to repair. Air Leakage: If your boat appears a bit soft, it might not be because of a leak, since any change in temperature can cause modifications 0.003 bar (0.045 psi) per Celsius degree (34F).
7. Fold the bow section on top of the previously folded rear part of the boat. Place the boat inside your Silver Marine® carry bag or protective covering. When storing your inflatable boat, ensure protection against rodents and other vermin, as they feed on the fabric of the boat.
OPERATION Rowing Silver Marine® transom boats are great tenders and can be rowed easily. The oars are attached to the swiveling oarlocks, which allow for easy rowing. Snap the rear blade section of the oar out of the clasp and the oarlock will pivot out for instant use. You can remove the oar from the oarlock by unscrewing the plastic nut on the oar.
TROUBLESHOOTING CHART PROBLEM POSSIBLE REASONS POSSIBLE SOLUTION(S) Rise or drop of temperature MAINTENANCE Plastic valve cap has not been fitted MAINTENANCE Buoyancy chamber looses air Loose valve MAINTENANCE Puncture REPAIRING Engine is incorrectly mounted MOTOR INSTALLATION Boat does not get on plane Load is not distributed correctly MOTOR INSTALLATION...
Need help?
Do you have a question about the Nemo 240 AD and is the answer not in the manual?
Questions and answers