DPP-MS300E SERVICE MANUAL AEP Model UK Model SPECIFICATIONS – Continued on next page – DIGITAL PHOTO PRINTER 9-928-127-31...
Page 2
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
TABLE OF CONTENTS GENERAL Identifying the parts ............. 1-1 Setting Up ..............1-1 Printing ................. 1-4 Making Various Prints ..........1-6 About “Memory Stick” ..........1-10 About PC Cards ............1-10 DISASSEMBLY ............2-1 MECHANICAL ADJUSTMENTS ....3-1 ELECTRICAL ADJUSTMENTS ......
Page 4
SECTION 1 This section is extracted from in- struction manual (3-866-753-11). GENERAL...
Page 16
MP-40 BOARD SECTION 6 harness (HH-C00-010-BB) 5 two screws (BV2.6 × 8) 7 MP shield case 0 PCMCIA ejector 8 MP-40 board 9 four screws (P2 × 6.5) 1 two screws (BV2.6 × 8) 2 MP bracket ass’y 3 card panel 4 card select lever ESCUTCHEON (60) BLOCK ASS’Y, MECHANISM DECK SECTION 6 two screws...
Page 17
HEAD MOTOR BLOCK ASS’Y (HEAD UP/DOWN) (M902) 3 two screws (BVTT 2.6 × 6) 4 bridge 7 head motor block ass’y (head up/down) (M902) 5 HM bracket ass’y 2 connector 6 two screws (CN1940) (PS 3 × 4) 1 two clamps (LOW TYPE) MD-40 BOARD 2 connector (CN1938)
Page 18
DC MOTOR (STEPPING MOTOR) (PLATEN) (M904), REEL MOTOR BLOCK ASS’Y (RIBBON) (M903) 6 reel motor block ass’y (ribbon) (M903) 5 two screws (PS2 × 4) 3 two screws (BVTT2.6 × 6) 2 DC motor (stepping motor) (platen) (M904) 4 motor bracket ass’y section 3 two screws (BVTT2.6 ×...
SECTION 3 MECHANICAL ADJUSTMENTS Replacing the Thermal Head 6) Remove the two screws 8 (PSW2.6 × 8) and remove the ther- 1) Before replacing the head, print the stair-step pattern with the mal head 9 from the heat sink 0. (Refer to Fig. 2) old head (faulty head).
SECTION 4 ELECTRICAL ADJUSTMENTS During the adjustment, see the Adjustment and Adjust- 2. Connection of Equipment ment Pats on page 4-7. Following the designation of input terminal (S-VIDEO or VIDEO), connect measuring units as shown in Fig. 4-1 and make adjust- Pre-Adjustment Preparations ment.
Page 21
3. Input Signal Check (2) When VIDEO is input The video circuit adjustment uses as adjustment signals the video Connect an oscilloscope to the VIDEO IN terminal, and check signals obtained from the pattern generator, and therefore these that the sync signal amplitude of VIDEO signal is 300 mV, video video output signals must be within the specification.
POWER SUPPLY BLOCK [Head Voltage Adjustment] Before performing this adjustment, print the stair-step pattern (Note 2) two times continuously with the old head (Note 1) or normal unit. The second print will be used as a sample of the print density.
[Y/C Separation CHROMA Level] (VI-40 board) VIDEO BLOCK Mode VIDEO Input [Free-Run Frequency Adjustment (1)] (VI-40 board) Signal Color bar (VIDEO IN) Mode VIDEO Input Measuring point CL129 Signal Color bar (S-VIDEO IN) (Note 1) Measuring equipment Oscilloscope IC108 !• pin Measuring point Adjustment part RV102...
Page 24
[D/A Output CHROMA Level Adjustment] (DK-40 board) [A/D Input R-Y/B-Y Level Adjustment] (VI-40, DK-40 board) Mode VIDEO Input Mode VIDEO Input Signal Color bar (VIDEO IN) Signal Color bar (S-VIDEO IN) Measuring point J1802 (OUTPUT) Measuring point CL407, 408 Measuring equipment Oscilloscope Measuring equipment Oscilloscope...
Page 25
[HUE Level Adjustment] (VI-40 board) Mode VIDEO Input Signal Color bar (S-VIDEO IN) Measuring point J1802 (OUTPUT) Measuring equipment Vector scope Adjustment part RV105 Specification value Yellow phase 167 ± 4 deg Adjustment Procedure: (1) Connect on vector scope to the J1802. (2) Press the S1707 (CAPTURE).
Page 26
Adjustment Parts and Measuring Points: – DK-40 BOARD (Side A) – RV404 A/D Input Y Level Adjustment CT401 910fh Adjustment CT500 IC407 Free-run Frequency (2) RV405 Adjustment A/D Input R/Y Level Adjustment RV401 RV402 D/A Output Y Level D/A Output Chroma Level Adjustment Adjustment –...
5-7. NOTES FOR PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM Note on Printed Wiring Board: Note on Schematic Diagram: • X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF • Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics •...
DPP-MS300E 5-23. SCHEMATIC DIAGRAM – HP-40/JD-40/MD-40/RD-40 Boards – • See page 5-57 for IC Block Diagrams. (Page 5-30) The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified.
Page 52
• IC Block Diagrams – VI-40 Board – IC101, 102 MM1113XFBE BUFFER BIAS IC103 CXA1229AM-T6 I REF VCC1 SYNC C SYNC OUT REGULATOR V REF C SYNC IN CHROMA OUT AUDIO OUT BUFFER AUDIO IN PULSE GENERATOR CHROMA IN NTSC/PAL Y IN PHASE SHIFTER...
5-24. IC PIN FUNCTION DESCRIPTION • DK-40 BOARD IC407 F432301PGF (A/D, D/A CONVERTER, MEMORY BUS CONTROL) Pin No. Pin Name Description MDT15 Two-way data bus with the D-RAM (IC403) (upper 8 bit) DGND — Ground terminal (logic system) DVCC — Power supply terminal (+5V) (logic system) 4, 5 MAD11, MAD10...
Page 57
Pin No. Pin Name Description TSTC TSTB TSTA Input terminal for the test (normally: fixed at “L”) TST2 TST1 TST0 DVCC — Power supply terminal (+5V) (logic system) DVCC — Power supply terminal (+5V) (A/D converter, digital system) AGND — Ground terminal (A/D converter, analog system) VRT1 Reference voltage (top side) input of the A/D converter...
Page 58
Pin No. Pin Name Description MNT2 Test monitor output terminal (normally: open) MNT1 Test monitor output terminal (normally: open) DVCC — Power supply terminal (+5V) (logic system) PCSX Chip select signal output to the mechanism controller (IC505) DCSX Chip select signal output terminal Not used (open) Data write end latch pulse input from the system controller (IC503) VRSR Refresh stop request input from the system controller (IC503)
Page 59
• DK-40 BOARD IC503 HD6437045E18F (SYSTEM CONTROLLER) Pin No. Pin Name Description Status (CPU emancipation of memory bus) input from the A/D, D/A converter (IC407) — Not used (open) VRSR Refresh stop request output to the A/D, D/A converter (IC407) Internal register data write end latch pulse output to the A/D, D/A converter (IC407) VTRS Busy signal input from the A/D, D/A converter (IC407)
Page 60
Pin No. Pin Name Description 3.3V/5V 3.3V/5V selection signal output terminal “L”: 3.3V, “H”: 5V Setting terminal for the destination Not used (open) Power on/off control signal output for the PC card and memory stick interface power supply “H”: power on —...
Page 61
Pin No. Pin Name Description MD1/BOOT Setting terminal for the CPU operational mode (fixed at “H” in this set) Setting terminal for the CPU operational mode (fixed at “L” in this set) PLL VCC — Power supply terminal (+5V) (PLL system) PLL CAP Connected to capacitor for the PLL PLL VSS...
Page 62
• DK-40 BOARD IC505 HG51BS263AFB (HEAD CONTROLLER, MECHANISM CONTROLLER) Pin No. Pin Name Description FKEY0 Sheets bit (0) input from the auto feeder unit FEEDER Auto feeder unit desorption detect input terminal “L”: attach, “H”: removed Auto feeder unit position detect sensor input terminal Busy signal in/out terminal Connected to TMGE (pin @§) BUSY HPS0...
Page 63
Pin No. Pin Name Description 62, 63 — Ground terminal Two-way data bus with the A/D, D/A converter (IC407), system controller (IC503), ROM 64 to 71 DT7 to DT0 (IC506), D-RAM (IC509), PC card controller (IC1501) and PC card slot (lower 8 bit) Data input from the centronics parallel port —...
Page 64
• MP-40 BOARD IC1501 HG72C306AH05TE1 (PC CARD CONTROLLER) Pin No. Pin Name Description H A2 Address signal input from the system controller (IC503) and PC card slot H INPACK Not used (pull up) H REG Register access signal input from the system controller (IC503) —...
Page 65
Pin No. Pin Name Description Address strobe signal output to the memory stick/PC card micro computer (IC1502), memory P AS stick controller (IC1503) and static RAM (IC1504) Address signal output to the memory stick/PC card micro computer (IC1502), memory stick P A17 controller (IC1503) and static RAM (IC1504) —...
Page 66
• MP-40 BOARD IC1502 HD6433032ST06X (MEMORY STICK/PC CARD MICRO COMPUTER) Pin No. Pin Name Description Reset signal output to the memory stick controller (IC1503) 2 to 4 — Not used (open) — Not used (open) Power on/off control signal output for the memory stick +3.3V power supply “H”: power on 7 to 10 —...
Page 67
• MP-40 BOARD IC1503 HG71G030A2R05TE (MEMORY STICK CONTROLLER) Pin No. Pin Name Description TEST Input terminal for the test Not used (open) A TST Input terminal for the test Not used (open) B TST Input terminal for the test Not used (open) 4 to 6 —...
Page 68
Pin No. Pin Name Description VCC 5V — Power supply terminal (+5V) 72, 73 — Not used (open) — Ground terminal Two-way data bus with the PC card controller (IC1501), memory stick/PC card micro computer 75 to 78 P D4 to P D7 (IC1502) and static RAM (IC1504) —...
SECTION 6 EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark may have some difference from the original are seldom required for routine service.
Page 74
(6) LOWER CABINET SECTION harness (HH-C00-010-BB) not supplied M905 not supplied The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No.
SECTION 7 DK-40 ELECTRICAL PARTS LIST NOTE: The components identified by • Due to standardization, replacements in the • Items marked “*” are not stocked since they mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.