Download Print this page
Monte Carlo Fan Company 3SKYR56XXD Series Owner's Manual And Installation Manual
Monte Carlo Fan Company 3SKYR56XXD Series Owner's Manual And Installation Manual

Monte Carlo Fan Company 3SKYR56XXD Series Owner's Manual And Installation Manual

Advertisement

Quick Links

Owner's Guide and Installation Manual
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
MODEL NUMBER:
To register your fixture, please visit our website www.montecarlofans.com
3 0 6 4 9 6 4
3SKYR56XXD Series Fan
ETL Model NO. : 3SKYR56(XXXXX)
RETAILER NAME:
RETAILER ADDRESS:
7.9 kgs
17.4 lbs
Total fan weight with light

Advertisement

loading
Need help?

Need help?

Do you have a question about the 3SKYR56XXD Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Monte Carlo Fan Company 3SKYR56XXD Series

  • Page 1 Owner’s Guide and Installation Manual 3SKYR56XXD Series Fan ETL Model NO. : 3SKYR56(XXXXX) Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: RETAILER ADDRESS: MODEL NUMBER: To register your fixture, please visit our website www.montecarlofans.com 7.9 kgs...
  • Page 2: Cautions And Warnings

    Note: Suitable for use in damp locations. Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses, Stepladder and Wire Strippers Customer Service 800-969-3347 Customer Service Center 7400 Linder Ave. Skokie, IL 60077 www.montecarlofans.com © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 3 Place downrod over canopy and yoke Partially loosen downrod set screws from cross pin from downrod. cover. yoke at top of motor assembly. Thread lead wires and safety cable from motor assembly through downrod. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 4 Make sure that no filaments are outside of the wire connectors. the lead wires. Insert the remote receiver into mounting bracket. Note : If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts In The Outlet Box. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 5 Loosen 2 and remove 1 preassembled with the preassembled screws on the screw from the light pan. Save screw for plate. Twist clockwise till lock. Reinstall later use. the screw removed in step 14. Tighten all screws securely. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 6 LED light, go to step 21 for blanking plate installation. Install blanking plate Light pan Blanking plate Attach blanking plate to light pan by locating dimples in light pan with grooves in blanking plate and twist clockwise until tight. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 7: Transmitter Operation

    Or you may turn power off for 15 seconds then turn power back, and then turn the fan on, Over load protection (current limit)- The device will limits the maximum current output from the receiver/drive when the fan or light load was increased abnormally. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 8 4. When fan is turned on or operated forward/reverse function, it shutters & goes back & forth until it turns. It is a normal performance of this fan and it will take for few seconds to run this operation. © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 9: Troubleshooting

    Trouble Shooting Warning Trouble Suggested Remedy CAUTION CAUTION CAUTION © 2014 Monte Carlo Fan Company 12/1/2014...
  • Page 10 Dec.2014...