Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Woosh Manuals
  4. Bicycle
  5. Big Bear
  6. User manual

Woosh Big Bear User Manual

Hide thumbs Also See for Big Bear:

Advertisement

Quick Links

Download this manual
Big Bear User Guide
Please read this manual.
It contains important information regarding
your safety, the correct use of the bike and
how to avoid expensive repair fees
in the future .
Support is available Mon to Fri from 10am to 5pm on
01702 684444 If there is no answer, leave a message and
we will call you back.
Sales: 01702 435566 — Support: 01702 684444 — E-mail: support@wooshbikes.co.uk
1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Big Bear and is the answer not in the manual?

Questions and answers

Related Manuals for Woosh Big Bear

Summary of Contents for Woosh Big Bear

  • Page 1 Big Bear User Guide Please read this manual. It contains important information regarding your safety, the correct use of the bike and how to avoid expensive repair fees in the future . Support is available Mon to Fri from 10am to 5pm on 01702 684444 If there is no answer, leave a message and we will call you back.
  • Page 2 The Big Bear from Woosh The Big Bear is a strong sturdy bike which can be used for commuting to and from work. It has a 15Ah bat- tery which means that distances of up to 50-60 miles can be achieved on a single charge in ideal condi- tions.
  • Page 3 See the maintenance manual for how to adjust and maintain the various components of the bike. Please note that failure to carry out these checks properly could result in serious injury for which Woosh Bikes Ltd will not be held liable.
  • Page 4 Unpacking: Two people are required to unpack the bike. Stand the carton upright as shown. Remove the shipping straps, cut the tape seals and then remove all of the polystyrene packaging. Keep the carton/bike in the upright position, and then lift the bike out of the carton and then lean it against a sturdy surface.
  • Page 5 Fitting the torque arm(s): The torque arm is a secondary measure to secure the motor wheel to the bike. It is essential that this de- vice is fitted to ensure your safety. The torque arms should be fitted to the both sides of the bike as shown. Remove the wheel nut and slide the arm into position on the axle and then refit the nut to secure it in position.
  • Page 6 Handlebars: If you haven’t already, slide the handlebar stem into the frame at the desired height, remove the weather- proof cap and then tighten the allen bolt indicated below to secure the stem in position whilst ensuring that the handlebars line up correctly with the front wheel. Once the stem has been secured, you can now fine tune the positioning of the handlebars.
  • Page 7 Seat-post/saddle: The seat-post simply slides into position and then the clamp is used to secure it. To adjust the height of the saddle, simply open the clamp and position the seat-post at the desired height and then close the clamp to lock it into position. It may be necessary to tighten the thumb screw a little to ensure that when the clamp is closed the seat-post is properly secured.
  • Page 8 Once unlocked remove the key and then slide the battery from the bike using the grip at the rear underside of the battery. Remember to separate your keys, Woosh Bikes is not able to supply replacements if you lose them.
  • Page 9 Obviously the bike shop will you charge for this service. Woosh Bikes not reimburse you for these costs.
  • Page 10 UK law. The Big Bear comes with a throttle control. The throttle is located on the right side of the handlebars as shown below. When the throttle is pulled fully, the motor will provide the most assistance. The throttle fea- ture is enabled/disabled by the red button as indicated below.
  • Page 11 The Big Bear also comes equipped with a horn which is powered from the main battery on the bike. To activate the horn (which is quite loud), simply press the red button indicated below.
  • Page 12 Fitting/Operating the lights: The rear light is already fitted, to operate the rear light, simply press the button on the top of the light as shown below. To change the batteries in this unit, simply reach under the bottom edge and then pull the lower edge of the light rearwards.
  • Page 13 To attach the light to the handlebars, undo the thumbscrew and slide the fitting over the handlebars, then re-tighten the thumbscrew to secure the fitting in place. Once in place you can slide the light/torch into po- sition a shown. It may be necessary to adjust the thumbscrew on the left side of the light to hold it firmly in position.
  • Page 14 King-Meter—Advanced The King-Meter has many advanced features and modes, these include back-lit display (for night riding), indicator options for max speed, average speed and current speed, a digital clock and a battery power in- dicator. Battery Level Indicator Assistance Level (Pedal Assist) Odometer Digital Clock Speed Indicator...
  • Page 15 Riding Distance/Total Distance To change the display between riding distance and total distance, press the Mode button. The current mode is indicated by “Trip” for “Current Trip Distance” and by “Odo” for “Total Distance”. Control Module Battery The “control module” itself has a battery which retains the settings within the module. This battery should last for around 2 years.

  • Page 16: Declaration Of Conformity

    Woosh Sant Ana Woosh Sant Ana CD/CDL Manufacturer, address Made in China for Woosh Bikes Ltd 42-46 Queens Road, Southend-on-Sea, Essex, SS1 1NL, UK The product (system) identified above is in conformity with the listed European Directive(s). The following table identifies the applied standards and the conformity assessment procedure.
  • Page 17 Email: support@wooshbikes.co.uk Telephone: 01702 684444 (If there is no answer, leave a brief message and contact no. and someone will call you back asap). Support staff are available 10am to 5pm Monday to Friday. © 2014 Woosh Bikes Limited...