Related Manuals for CCTV EL-15MB1R
Summary of Contents for CCTV EL-15MB1R
-
Page 1: User Manual
Introduction CCTV LCD Monitor User Manual For models: EL-15MB1R EL-17MB1R EL-19MB1R _____________________... -
Page 2: Table Of Contents
Contents 1. Introduction………............................3 2. Work Safety Information..........................4 2.1. Product Safety Precautions information.......................4 2.2. Safety Guidelines............................5 2.3. Important Notice Concerning Power Cord Selection...................5 2.3.1 For the United States and Canada..................... 5 2.3.2 For European Countries........................5 2.3.3 For the United Kingdom........................6 3. -
Page 3: Introduction
Introduction Thank you for purchasing the professional CCTV LCD Monitor and welcome to a fantastic new technology that will completely change the way you look at monitors. The following sections describe just a few of the major advantages of this LCD monitor. You’ll discover more of its wonderful features as you use it. -
Page 4: Work Safety Information
No internal parts can be serviced by users. Refer servicing to qualified personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS CCTV LCD MONITOR TO RAIN OR MOISTURE. “HIGH VOLTAGE EXISTS ON THE BACK LIGHT POWER LEAD OF THIS WARNING CCTV LCD MONITOR. -
Page 5: Safety Guidelines
Safety Guidelines WARNING This device must be operated with the original power supply. The socket outlet should be installed near the equipment and should be CAUTION easily accessible. Use a power cord that is properly grounded. Always use the appropriate AC power cord that is certified for the individual country. -
Page 6: For The United Kingdom
2.3.3 For the United Kingdom For your safety please read the following text carefully. If the fitted molded plug is unsuitable for the socket outlet, then the plug should be cut off and disposed of safely. Do not plug the cut-off plug into a socket outlet! There is a danger of severe DANGER electrical shock! If a new plug is to be fitted, please observe the wiring code as shown below. -
Page 7: Standards And Guidelines
Standards and Guidelines FCC Requirements This device complies with Part 15 of the FCC Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must tolerate any interference encountered, including interference that may cause improper operation. -
Page 8: Rohs Compliance Statement
RoHS Compliance Statement This display defined in this user manual is 100% RoHS complaint and meets all the requirements set forth in European Union Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment. Information on Disposal for Your Old Product Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment. -
Page 9: Hardware Installation
Hardware This chapter will guide you through the correct installation procedures for the LCD monitor. 4.1. Checking the Accessories Supplied LCD monitor body + Desk Stand x 1 pc AC power cord x 1 pc Adaptor x 1 pc D-Sub 15-pin cable (1.8 Meter) x 1 pc Ø... -
Page 10: Buttons And Connections
5. Buttons and Connections 5.1 Buttons ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ “Menu/Enter” : To Enter the OSD menu or confirm the setting. ○... -
Page 11: Connections
5.2 Connections Item Connector Function ○ DC 12 Input Please use DC 12V, 5A Power Adaptor ○ PC Audio Input (Ø 3.5mm) Connect to the audio output of your computer ○ Stereo RCA Audio Input Stereo audio input , “R“ is right channel (Red) of audio connector, (L/R) “L“... -
Page 12: Id Remote Controller
6. ID Remote Controller The ID function is only applicable for some specific models ) . POWER switch. Press to turn ON or turn OFF the LCD Monitor. VIDEO SIGNAL Selection: Press the “AV1” ,“AV2”, “S-VIDEO”, “D-SUB”, “HDMI” button to enter the selected video source or press the “SOURCE” button to have the cycle video selection. -
Page 13: Osd Setup
Step 2: Control the monitor with ID No. Press “ID“ button, the screen will dispaly the“ ID NO.“, input 4 same digit on “ ID “ and press “ENTER“ to confrim the input. Then you can control the monitor. For example: When you setup the Monitor “ID NO“... - Page 14 Tint Press “▲/+” or “▼/-“ to increase/decrease the “Blue bar” to adjust hue. Using hue to adjust the color of flesh tones. Increasing figure will make the picture with more red in appearance. Decreasing figure will shift the picture with more green in appearance. Saturation Press “▲/+”...
- Page 15 PIP (Video Mode) Press the “Menu” key on the buttons to call out the OSD “Menu” . Press “▲/+” or “▼/-“ to select “PIP” mode and press “Menu” key again to select the “PIP” option. Sub Source Press the “Menu” key to enter the Sub Source and press “▲/+” or “▼/-“ to select PC as the sub-screen . Sub Size Press the “Menu”...
- Page 16 Image Ratio (Video/HDMI mode) In order to meet different applications in video output, there are 5 image ratio to choose (1) 5:4 Full (2) 4:3 Under-V (3). 4:3 Over-H (4). 5:4 Over-1 (5). 5:4 Over-2. Press “▲/+” or “▼/-“ key to select the format ratio you want.
- Page 17 5. 5:4 Over-2 The format is another over scan mode to make the image fill up the screen and cut about 3% on “Vertical” and 6% on “Horizontal” lines.. Image Optimize Select the “ Image Optimize” for best image setting. Press “Menu” to enter “OK” mode. To select DNR (Dynamic Noise Reduction), the DNR will reduce the noise level and improve the video quality.
- Page 18 The ID function is only applicable for some specific models, if the model you brought has the ID function, Please check the ID setup procedure on page 9. Default If you want to back to factory default, press “▲/+” or “▼/-“ key to select “ Default” “ and press “Enter” key to activate “OK”...
- Page 19 Sound (PC/HDMI Mode) The setup is the same as page No.11 for sound setup of “Video Mode”. PIP (PC/HDMI Mode) The setup is the same as page No. 11 for PIP setup of “Video Mode”. Display (PC/HDMI Mode) Press the “Menu” key on the buttons to call out the OSD “Menu”...
- Page 20 Image Ratio(PC Mode) In order to meet different applications in video output, there are 2 image ratio to choose (1) 4:3 (2) 16:9 Press “▲/+” or “▼/-“ key to select the ratio you want. 1. 4:3 The image fully fills up the 4:3 screen on both “Vertical” and “...
- Page 21 Function (PC/ HDMI Mode) The setup is the same as page 12 for Function adjustment of “Video Mode”. Exit Press the “Menu” key and press “▲/+” or “▼/-“ to select “Exit” to exit the OSD menu.
-
Page 22: Troubleshooting Guide
8. Troubleshooting Guide When you experience issues with the CCTV LCD Monitor , before contacting your retailer where you made your purchase, please check the following items. The most common issue is with the connection of AV equipment or graphic card. We recommend that at the same time of troubleshooting, also refer to the AV equipment or graphic card user manual. -
Page 23: Applicable Video Timing For Pc- Analog Video
Applicable Video Timing for PC- analog Video The following table list are the better display quality modes for analogy signal (PC) supported by this LCD monitor. The LCD monitor will stop working or has poor picture quality when other modes out of below list input. -
Page 24: Technical Data
10. Technical Data Model EL-15MB1R EL-17MB1R EL-19MB1R System Panel Size 15” LCD 17” LCD 19” LCD Resolution 1024 x 768 1280 x 1024 1280 x 1024 Pixel Pitch (H x V) 0.297 x 0.297 mm 0.264 x 0.264 mm 0.294 x 0.294 mm... -
Page 25: Dimension
Dimension EL-15MB1R EL-17MB1R EL-19MB1R...