THUNDER TIGER titan x50 Instruction Manual page 23

Main Frame Assembly-8 / 本體組裝-8
Bag H+K
No. Material No. Description
1 HMM3Z
NYLON NUT,M3
2 BK0077 COLLAR,d3xD4xW6
3
HMV740ZZY BEARING,d4xD7xW2.5
4 BK0649-2
LINKAGE BALL(B)
5 BK2160-R 120° CONTROL ARM-R
6
BK2160-L 120° CONTROL ARM-L
7 BK2227
ARM COLLAR
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
HMV740ZZY
BEARING,d4xD7xW2.5
滾珠軸承,d4xD7xW2.5
BK0649-2
LINKAGE BALL(B)
內六角連接頭自攻螺絲(B)
HME3-30B
SET SCREW,M3x30
無頭內六角螺絲,M3x30
HMC2512B
SOCKET SCREW,M2.5x12
內六角螺絲,M2.5x12
HMV1680ZZY
BEARING,d8xD16xW5
滾珠軸承,d8xD16xW5
Apply C.A Glue
使用快乾膠黏合
Step 2
1. Attach the Bearing into the Rubber Bearing Support.
2. Screw the Shaft End onto the Tail Drive Shaft with a drop of threadlocker
as the drawing, but do not over tighten.
3. Add a drop of thin CA glue on the Tail Drive Shaft next to where the
bearing should be, and then slide the bearings over the position quickly;
the distance from the Shaft Drive End to the Rubber Shaft Bearing
Support is approx. 350mm / 13.78".
4. Apply some amount of silicon oil or Vaseline onto the rubber surface for
easy install into the tail boom later.
名稱
止鬆螺帽,M3
軸環,d3xD4xW6
滾珠軸承,d4xD7xW2.5
內六角連接頭自攻螺絲(B)
120° 控制搖臂(右)
120° 控制搖臂(左)
擺臂固定軸環
Step 1 / 步驟一
Attach the Control Arms onto the Main Frame Set as drawing, and note the difference of
Left & Right Control Arms, please refer the "120L"/ "120R" mark on the arms.
參考圖示將控制搖臂裝上主側板上，請注意左、右邊的控制搖臂不同，請對照控制搖臂上L或R凸字
安裝。
HMM25Z
NYLON NUT, M2.5
止鬆螺帽, M2.5
(8)
(4)
(2)
(3)
(1)
(4)
(5) Right side
(3)
右側
Tail
尾座
(12)
(13)
The hole with a round chamfer
goes toward the tail。
有倒角的孔徑朝向尾座。
(10)
Qty No. Material No. Description
8 HME3-30B
2
2 9 BK2529
10
4 HMV1680ZZY
11 BK2552
6
1 12 HMC2512B
13
1 HMM25Z
14 BK0367
2
(7)
(11)
(9)
-22-
名稱
SET SCREW,M3x30 無頭內六角螺絲,M3x30
傳動軸軸承套
TAIL DRIVE SHAFT BRG
滾珠軸承, d8xD16xW5
BEARING, d8xD16xW5
尾驅動軸
TAIL DRIVE SHAFT
內六角螺絲, M2.5x12
SOCKET SCREW, M2.5x12
止鬆螺帽, M2.5
NYLON NUT, M2.5
尾驅動連接棒
TAIL DRIVE SHAFT LINKER
Left side
(6)
左側
(4)
(7)
(8)
CA
(13)
(12)
步驟二
1. 將軸承擠壓入橡膠軸套內。
2. 參考圖示，塗抹些許防鬆膠將尾傳動軸接頭
鎖在尾傳動軸，但勿過度鎖緊。
3. 在尾傳動軸上軸承固定位置前方，塗抹少量
快乾膠，迅速滑動軸承至定位固定；該定位
大約距離軸傳動接頭350mm / 13.78"處。
4. 塗抹些許矽膠油脂或凡士林於橡膠軸套表面
上，稍後將尾驅動軸組裝入尾管時，會較為
容易。
Qty
2
1
1
1
2
2
2
(4)
(3)
(1)
(2)
(4)
(3)
Collar
軸環
21mm
Frame 側板
CA
(14)
Nose
機頭