Canon PIXMA MP610 Series Quick Start Manual page 91

d.·.,.·U.·.I.·,.·
::lY'".c o
• Error No.: 300 Is Displayed
Cause
I
Action
The machine is not ready.
Machine is not connected properly.
Your machine is not selected in Printer
on the Print dialog box.
Confirm that the Power lamp is lit green.
If the Power lamp is off, turn the machine on.
If the Power lamp is flashing green, the machine is initializing. Wait until the
Power lamp stops flashing and remains lit green.
If the Alarm lamp is lit orange, an error may have occurred in the machine. For
details on how to resolve the error, see "An Error Message Is Displayed on the
LCD" on page 70.
Make sure that the USB cable is plugged in securely to the machine and the
computer.
• If you are using a relay device such as a USB hub, disconnect it, connect the
machine directly to the computer, and try printing again. If printing starts
normally, there is a problem with the relay device.
Consult the reseller of the relay device for details.
• There could also be a problem with the USB cable. Replace the USB cable
and try printing again.
Select your machine's name in Printer on the Print dialog box.
If your machine's name does not appear in Printer, follow the procedure below
to check that the driver for your machine is installed to your computer.
(1)Select Print & Fax Preferences from Printer.
In Mac
as x
v 10.2.8 or 10.3.x, select Edit Printer List from Printer.
(2) Check that your machine's name is displayed in the list of printers and that
the check box is selected.
In Mac
as x
v.1 0.2.8, check that your machine's name is displayed in
Printer List.
(3) If your machine's name is not displayed, click Add(+) to add the machine.
If you cannot add the machine, follow the procedure described in your setup
sheet to reinstall the MP Drivers.
• Error No.: 1700 Is Displayed
See "The ink absorber is almost full. Press OK to continue printing. Contact the
service center." in "An Error Message Is Displayed on the LCD" on page 71.
tllll
• Error No.: 1851 Is Displayed
Inner Cover was open when you
started printing.
Close the Inner Cover, press the OK button on the machine.
again.
Troubleshooting
87
d.·.,.·U.·.I.·,.·
::lY'".c o
• Error No.: 300 Is Displayed
Cause
I
Action
The machine is not ready.
Machine is not connected properly.
Your machine is not selected in Printer
on the Print dialog box.
Confirm that the Power lamp is lit green.
If the Power lamp is off, turn the machine on.
If the Power lamp is flashing green, the machine is initializing. Wait until the
Power lamp stops flashing and remains lit green.
If the Alarm lamp is lit orange, an error may have occurred in the machine. For
details on how to resolve the error, see "An Error Message Is Displayed on the
LCD" on page 70.
Make sure that the USB cable is plugged in securely to the machine and the
computer.
• If you are using a relay device such as a USB hub, disconnect it, connect the
machine directly to the computer, and try printing again. If printing starts
normally, there is a problem with the relay device.
Consult the reseller of the relay device for details.
• There could also be a problem with the USB cable. Replace the USB cable
and try printing again.
Select your machine's name in Printer on the Print dialog box.
If your machine's name does not appear in Printer, follow the procedure below
to check that the driver for your machine is installed to your computer.
(1)Select Print & Fax Preferences from Printer.
In Mac
as x
v 10.2.8 or 10.3.x, select Edit Printer List from Printer.
(2) Check that your machine's name is displayed in the list of printers and that
the check box is selected.
In Mac
as x
v.1 0.2.8, check that your machine's name is displayed in
Printer List.
(3) If your machine's name is not displayed, click Add(+) to add the machine.
If you cannot add the machine, follow the procedure described in your setup
sheet to reinstall the MP Drivers.
• Error No.: 1700 Is Displayed
See "The ink absorber is almost full. Press OK to continue printing. Contact the
service center." in "An Error Message Is Displayed on the LCD" on page 71.
tllll
• Error No.: 1851 Is Displayed
Inner Cover was open when you
started printing.
Close the Inner Cover, press the OK button on the machine.
again.
Troubleshooting
87