FEATURES ..............................................................................................................................................4
PARTS LIST ...........................................................................................................................................35
AV-21L11 AV-21L31 AV-25L31 SPECIFICATIONS Contents Items AV-21L11-PH AV-21L31-PH AV-25L31-PH Dimensions (W × H × D) 59.8cm × 46.8cm × 47.15cm 68.2cm × 53.84cm × 47.75cm Mass 22kg 32kg TV RF System CCIR(M) Color System TV Mode NTSC3.58 VIDEO Mode NTSC3.58...
AV-21L11 AV-21L31 AV-25L31 SAFETY PRECAUTIONS 1. The design of this product contains special hardware, many circuits 8. When service is required, observe the original lead dress. Extra and components specially for safety purposes. For continued pro- precaution should be given to assure correct lead dress in the high tection, no changes should be made to the original design unless voltage circuit area.
AV-21L11 AV-21L31 AV-25L31 FEATURES s New chassis design enables use of an interactive on-screen control. s Built-in DIGITAL ECO MODE (ECONOMY, ECOLOGY). s Pure flat CRT produces fine textured picture in every detail. In accordance with the brightness in a room, the brightness and/or s Wide range voltage (110V ~ 240V) for AC power input.
AV-21L11 AV-21L31 AV-25L31 SPECIFIC SERVICE INSTRUCTIONS DISASSEMBLY PROCEDURE REMOVING THE REAR COVER 1. Unplug the power supply cord. Å ı 2. Remove the 7 or 9 screws marked and 4 screws maked shown in Fig.1. 3. Withdraw the Rear cover toward you.
Page 7
AV-21L11 AV-21L31 AV-25L31 PICTURE TUBE FRONT CABINET (×2) (×2) SPEAKER CRT SOCKET PWB MAIN PWB (×2) (×2) SPEAKER PB STOPPER REAR COVER (×7) [AV-21L11-PH, AV-21L31-PH] (×9) [AV-25L31-PH] Except 21” model (×4) Except 21” model Fig.1 No. 51904...
Page 8
AV-21L11 AV-21L31 AV-25L31 REMOVING THE CRT CRT CHANGE TABLE * Replacement of the CRT should be performed by 2 or more persons. • After removing the rear cover, chassis etc., 1. Putting the CRT change table on soft cloth, the CRT change table should also be covered with such soft cloth (shown in Fig.
AV-21L11 AV-21L31 AV-25L31 REPLACEMENT OF MEMORY IC 1. MEMORY IC (6) User setting This TV uses the following memory IC. Check the user setting values in Table 2, and if setting value is Memory IC: IC1702 on MAIN PW Board different, set the correct value.
Page 10
AV-21L11 AV-21L31 AV-25L31 SETTING OF SYSTEM CONSTANT SET Setting value Setting item Setting content AV-21L11-PH AV-21L31-PH AV-25L31-PH NTSC TRIPLE COLOR SYSTEM NTSC COMB TILT SUPER BASS B/B SOUND TUNER COLOR AUTO LOCK LONG WAIT SHORT WAIT Table 1 No. 51904...
AV-21L11 AV-21L31 AV-25L31 USER SETTING VALUES Setting item Setting value SUB POWER CHANNEL POSITION CH-02 CHANNEL PRESET REFER TO OPERATING INSTRUCTIONS VOLUME 15 ± 2 TV/VIDEO COMPRESS (16:9) AUTO SHUTOFF CHILD LOCK BLUE BACK VIDEO-2 SET VIDEO LANGUAGE MONO SURROUND...
Page 12
AV-21L11 AV-21L31 AV-25L31 SERVICE MENU SETTING ITEMS Service menu Setting item Service menu Setting item 1. IF 1. VCO 5. PRESET 1. CB 2. DELAY POINT 2. ACL Do not adjust 3. MUS 4. MAT 2. VC 1. CUTOFF(R/G) 5. FCO 2.
Page 13
AV-21L11 AV-21L31 AV-25L31 REPLACEMENT OF CHIP COMPONENT CAUTIONS 1. Avoid heating for more than 3 seconds. 2. Do not rub the electrodes and the resist parts of the pattern. 3. When removing a chip part, melt the solder adequately. 4. Do not reuse a chip part after removing it.
AV-21L11 AV-21L31 AV-25L31 SERVICE ADJUSTMENTS ADJUSTMENT PREPARATION: 1. You can make the necessary adjustments for this unit with either the remote control unit or with the adjustment equipment and parts as given below. 2. Adjustment with the remote control unit is made on the basis of the initial setting values, however, the new setting values which set the screen to its optimum condition may differ from the initial settings.
Page 16
AV-21L11 AV-21L31 AV-25L31 BASIC OPERATION IN SERVICE MENU 1. TOOL OF SERVICE MENU OPERATION Operate the SERVICE MENU with the remote control unit. 2. SERVICE MENU ITEMS With the SERVICE MENU,various settings (adjustments)can be made,and they are broadly classified in the following items of settings: •...
Page 17
AV-21L11 AV-21L31 AV-25L31 SERVICE MENU SUB MENU 1. IF SERVICE MENU VCO (CW) ***** TOO HIGH 1. IF 2. VC 1. VCO ABOVE REFERENCE 3. DEF 4. VSM PRESET BELOW REFERENCE 5. PRESET 6. AUDIO 2. DELAY POINT TOO LOW 7.
AV-21L11 AV-21L31 AV-25L31 ADJUSTMENTS B1 POWER SUPPLY Measuring Item Test point Adjustment part Description instrument Check of Signal B1 (pin 1) 1. Receive a black and white signal. Generator GND (pin 5) 2. Connect a DC voltmeter between B1 and GND...
Page 20
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument Signal 2. DRIVE (R) Notes: Adjustment of WHITE generator DRIVE (G) • Proceed to the following this adjustment after having completed the BALANCE DRIVE (B) adjustment of LOW LIGHT WHITE BALANCE.
Page 21
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument Remote 5. COLOR [Method of adjustment without measuring instrument] Adjustment control unit Notes: • Proceed to the following this adjustment after having completed the COLOR-I adjustment of SUB PICTURE.
Page 22
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument Adjustment Remote 6. TINT [Method of adjustment without measuring instrument] control unit Notes: SUB TINT-I • Proceed to the following this adjustment after having completed the adjustment of SUB PICTURE.
Page 23
AV-21L11 AV-21L31 AV-25L31 DEFLECTION CIRCUIT ADJUSTMENT The setting (adjustment) using the remote control unit is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
Page 24
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument Adjustment 2. VER. HEIGHT 9. Receive a NTSC cross-hatch signal. Signal 10. Select 2. VER. HEIGHT with the MENU &/^ key. 13. V. ZOOM generator V. ZOOM 11. Set the initial setting value of 2. VER. HEIGHT with the MENU –/+ key.
Page 25
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument 23. Select 7. EW-PIN with the MENU &/^ key. Adjustment 7. EW-PIN Signal 24. Set the initial setting value of 7. EW-PIN with the MENU –/+ key. generator EW-PIN 25.
Page 26
AV-21L11 AV-21L31 AV-25L31 Measuring Item Test point Adjustment part Description instrument 32. Select 9. UP CORNER with the MENU &/^ key. Adjustment 9. UP CORNER Signal 10. DW CORNER 33. Set the initial setting value of 9. UP CORNER with the MENU –/+...
Page 27
AV-21L11 AV-21L31 AV-25L31 [COMPRESS (16 : 9) ] Measuring Item Test point Adjustment part Description instrument Adjustment Signal 13. V. ZOOM 1. Receive a NTSC cross-hatch signal. generator 2. VER. HEIGHT 2. Select COMPRESS from the MENU and set COMPRESS to ON.
Page 28
AV-21L11 AV-21L31 AV-25L31 [COMPONENT] Measuring Item Test point Adjustment part Description instrument Adjustment 5. HOR. POSITION 1. Receive a NTSC circle pattern signal to VIDEO-2 terminal. Signal 2. Select VIDEO-2 SET from the MENU and set VIDEO-2 SET to generator HOR.
Page 29
AV-21L11 AV-21L31 AV-25L31 PRESET ADJUSTMENT • Do not adjust 5. PRESET in the SERVICE MENU as it requires no adjustment. [SUB MENU 5. PRESET] Initial setting value Setting item Variable range AV-21L11-PH AV-21L31-PH AV-25L31-PH IFLH AFCW 00/10/01 50 – 95 READ STATUS —...
Page 30
AV-21L11 AV-21L31 AV-25L31 PURITY AND CONVERGENCE ADJUSTMENTS Note: The final adjustment of CONVERGENCE must be done after the FOCUS adjustment. (CONVERGENCE is changed by FOCUS adjustment.) When makes difference by FOCUS adjustment, should be WEDGE DEFLECTION reconfirming PURITY adjustment. YOKE PURITY ADJUSTMENT 1.
Page 31
AV-21L11 AV-21L31 STATIC CONVERGENCE ADJUSTMENT [AV-21L11-PH, AV-21L31-PH] 1. Input a crosshatch signal. 2. Using 4-pole convergence magnets, overlap the red and blue lines in the centre of the screen (Fig. 4) and turn them to magenta (red/blue). (FRONT VIEW) 3. Using 6-pole convergence magnets, overlap the magenta(red/blue) and green lines in the center of the screen and turn them to white.
Page 32
AV-25L31 STATIC CONVERGENCE ADJUSTMENT [AV-25L31-PH] 1. Input a crosshatch signal. (FRONT VIEW) 2. Using 4-pole convergence magnets, overlap the red and blue lines in the centre of the screen (Fig. 7) and turn them to magenta (red/blue). 3. Using 6-pole convergence magnets, overlap the magenta(red/blue) and green lines in the center of the screen and turn them to white.
Page 33
AV-21L11 AV-21L31 AV-25L31 SELF-CHECK FUNCTIONS 1. Outline This model has self-check functions given below.When an abnormality has been detected,the SUB POWER is turned off and both ECO and ON TIMER LEDs flash to inform of the failure.An abnormality is detected by the signal input state of the control line connected to the microcomputer.
VICTOR COMPANY OF JAPAN, LIMITED HOME AV NETWORK BUSINESS UNIT 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan AV21L11PH-SK #4 Printed in Japan AV21L31PH-SK #4 VP0109 AV25L31PH-SK #4...