Motorola Talkabout KEM-ML36100-08A User Manual

MJ Series_Hybrid.qxp:T5025_R 4/28/11 1:54 PM Page 1
Body-Worn Operation
To maintain compliances with RF exposure regulatory guidelines, if
®
you wear a radio on your body when transmitting always place the
radio in a Motorola-supplied or approved clip holder, holster, case
or body harness for this product. Use of non-Motorola-approved
Two-Way Radio
accessories may exceed RF exposure regulatory guidelines.
User's Guide If you do not use one of the Motorola-supplied or approved body-
worn accessories and are not using the radio held in the normal use
position, ensure the radio and its antenna are at least 1 inch (2.5
cm) from your body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or
without an accessory cable, position the radio and its antenna at
least one inch (2.5 cm) from the body.
Approved Accessories
For a list of approved Motorola accessories, visit our Web site at
www.motorola.com.
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to
electromagnetic interference (EMI) if inadequately shielded,
designed or otherwise configured for electromagnetic compatibility.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference; and
2. This device must accept any interference received, including
interference that may cause undesired operation.
MJ Series
KEM ML36100 08A
IC Canada
The term "IC:" before the equipment certification number only
signifies that the Industry Canada technical specifications were met.
For More Information
Facilities
For further information, you may contact Motorola as follows:
To avoid electromagnetic interference and/or compatibility conflicts,
USA and Canada: Call 1-800-638-5119, send e-mail to
turn off your radio in any facility where posted notices instruct you
giant@callcenter.com or visit www.motorola.com.
to do so. Hospitals or health care facilities may be using equipment
Mexico: Call 01-800-021-0000.
that is sensitive to external RF energy.
Uruguay: Call 00-04-01-78-70-11.
Aircraft
Panama: Call 507-340-0293.
When instructed to do so, turn off your radio when onboard an
aircraft. Any use of a radio must be in accordance with applicable
regulations per airline crew instructions.
Safety and General Information
Medical Devices – Pacemakers
Important Information on Safe and Efficient Operation
The Advanced Medical Technology Association recommends that a
Read This Information Before Using Your Radio.
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations
The information provided in this document supersedes the general
are consistent with the independent research by and
safety information in user guides published prior to December 1, 2002.
recommendations of the U.S. Food and Drug Administration.
Transmit and Receive Procedure
People with pacemakers should:
Your two-way radio contains a transmitter and a receiver. To control
• ALWAYS keep the radio more than 6 inches (15 cm) from their
your exposure and ensure compliance with the general population/
pacemaker when the radio is turned ON.
uncontrolled environment exposure limits, always adhere to the
following procedure:
• Not carry the radio in the breast pocket.
• Transmit no more than 50% of the time.
• Use the ear opposite the pacemaker to minimize the potential
for interference.
• To receive calls, release the PTT button.
• Turn the radio OFF immediately if there is any reason to suspect
• To transmit (talk), press the Push-to-Talk (PTT) button.
that interference is taking place.
Transmitting 50% of the time, or less, is important because the radio
generates measurable RF energy exposure only when transmitting Medical Devices – Hearing Aids
(in terms of measuring standards compliance). Some digital wireless radios may interfere with some hearing aids.
In the event of such interference, you may want to consult your
Exposure to Radio Frequency Energy
hearing aid manufacturer to discuss alternatives.
Your Motorola two-way radio complies with the following RF energy
exposure standards and guidelines: Medical Devices – Other
If you use any other personal medical device, consult the
• United States Federal Communications Commission, Code of
manufacturer of your device to determine if it is adequately
Federal Regulations; 47CFR part 2 sub-part J.
shielded from RF energy. Your physician may be able to assist you in
• American National Standards Institute (ANSI)/Institute of
obtaining this information.
Electrical and Electronic Engineers (IEEE) C95. 1-1992.
Safety and General Use While Driving
• Institute of Electrical and Electronics Engineers (IEEE) C95.
Check the laws and regulations regarding the use of radios in the
1-1999 Edition.
area where you drive, and always obey them. If you do use your
• International Commission on Non-Ionizing Radiation Protection
radio while driving, please:
(ICNIRP) 1998.
• Give full attention to driving and to the road.
• Ministry of Health (Canada) Safety Code 6. Limits of Human
• Use hands-free operation, if available.
Exposure to Radiofrequency Electromagnetic Fields in the
• Pull off the road and park before making or answering a call if
Frequency Range from 3 KHz to 300 GHz, 1999.
driving conditions so require.
• Australian Communications Authority Radiocommunications
The use of a two-way radio while engaged in activities requiring
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
concentration may cause distraction or otherwise impair your
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
ability to safely participate in such activities. Always use technology
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
safely.
To ensure optimal radio performance and make sure human
Do not place a portable radio in the area over an air bag or in the
exposure to radio frequency electromagnetic energy is within the
air bag deployment area. Air bags inflate with great force. If a
guidelines set forth in the above standards, always adhere to the
portable radio is placed in the air bag deployment area and the air
following procedures.
bag inflates, the radio may be propelled with great force and cause
Portable Radio Operation and EME Exposure serious injury to occupants of the vehicle.
Antenna Care
Potentially Explosive Atmospheres
Use only the supplied or an approved replacement antenna.
Turn off your radio prior to entering any area with a potentially
Unauthorized antennas, modifications, or attachments could
explosive atmosphere. Only radio types that are especially qualified
damage the radio and may violate FCC regulations.
should be used in such areas as "Intrinsically Safe." Do not remove,
install or charge batteries in such areas. Sparks in a potentially
Do NOT hold the antenna when the radio is "IN USE." Holding the
explosive atmosphere can cause an explosion or fire resulting in
antenna affects its effective range.
bodily injury or even death.
Note: The areas with potentially explosive atmospheres referred to Channels and Frequencies
above include fueling areas such as below decks on boats, fuel or
Channel Frequency
chemical transfer or storage facilities, areas where the air contains
chemicals or particles (such as grain, dust or metal powders) and
1 462.5625 MHz
any other area where you would normally be advised to turn off your
vehicle engine. Areas with potentially explosive atmospheres are
2 462.5875 MHz
often—but not always—posted.
3 462.6125 MHz
Blasting Caps and Areas
To avoid possible interference with blasting operations, turn off your
4 462.6375 MHz
radio when you are near electrical blasting caps, in a blasting area,
or in areas posted "Turn off two-way radios." Obey all signs and
5 462.6625 MHz
instructions.
Operational Cautions 6 462.6875 MHz
Antennas
7 462.7125 MHz
Do not use any portable radio that has a damaged antenna. If a
damaged antenna comes into contact with your skin, a minor burn
8 467.5625 MHz
can result.
9 467.5875 MHz
Batteries
All batteries can cause property damage and/or bodily injury such as
10 467.6125 MHz
burns if a conductive material—like jewelry, keys or beaded chains—
touch exposed terminals. The conductive material may complete an
11 467.6375 MHz
electrical circuit (short circuit) and become quite hot. Exercise care in
handling any charged battery, particularly when placing it inside a
Mexico
pocket, purse or other container with metal objects.
Use of GMRS frequencies is subject to the Rules and Regulations of
Exercise care when removing NiMH or AA batteries. Do not use
the Secretary of Communications and Transport (SCT) and Federal
sharp or conductive tools to remove either of these batteries.
Telecommunications Commissions (COFETEL). SCT/COFETEL
requires that all operators using GMRS frequencies obtain a permit
Battery Charger Safety Instructions:
before operating their equipment. To obtain a permit from the SCT,
Save these Instructions
the user must proceed in accordance with Articles 14 and 15 of the
1. Do not expose the charger to rain or snow.
Federal Telecommunications Law. Consult your local SCT/COFETEL
2. Do not operate or disassemble the charger if it has received a
office for more information: www.sct.gob.mx./www.cft.gob.mx.
sharp blow, or has been dropped or damaged in any way.
Uruguay
3. Never alter the AC cord or plug provided with the unit. If the
Use of GMRS frequencies is subject to the Rules and Regulations of
plug will not fit the outlet, have the proper outlet installed by a
the Regulatory Unit Communications Services (URSEC). URSEC
qualified electrician. An improper condition can result in a risk
requires that all operators using GMRS frequencies obtain a permit
of electric shock.
before operating their equipment. The authorization shall depend on
4. To reduce the risk of damage to the cord or plug, pull the plug
the channel availability at the time the authorization is requested. To
rather than the cord when disconnecting the charger from the
obtain a permit from URSEC, consult your local URSEC office for
AC receptacle.
more information: www.ursec.gub.uy.
5. To reduce the risk of electric shock, unplug the charger from the
Panama
outlet before attempting any maintenance or cleaning.
The Republic of Panama does not require authorization to use
6. Use of an attachment not recommended or sold by Motorola
FRS/GMRS radio equipment frequencies.
may result in a risk of fire, electric shock or personal injury.
USA
7. Make sure the cord is located so it will not be stepped on,
tripped over or subjected to damage or stress. Use of GMRS frequencies is subject to the Rules and Regulations of
the Federal Communications Commission (FCC). The FCC requires
8. An extension cord should not be used unless absolutely
that all operators using GMRS frequencies obtain a radio license
necessary. Use of an improper extension cord could result in a
before operating their equipment. To obtain the FCC forms, please
risk of a fire and/or electric shock. If an extension cord must be
visit the FCC's Web site at wireless.fcc.gov/uls/index.htm?job=home
used, make sure that:
to source form 605 and 159, which include all the instructions you
• The pins on the plug of the extension cord are the same
will need.
number, size and shape as those on the plug of the charger.
If you wish to have the document faxed or mailed, or if you have
• The extension cord is properly wired and in good electrical
questions, please use the following contact information:
condition.
• The extension cord size is 18 AWG for lengths up to 100 feet,
For a fax:
and 16 AWG for lengths up to 150 feet.
Contact the
9. The supply cord of the AC adaptor cannot be replaced. If the Fax-0n-Demand
cord is damaged, call customer service at the appropriate system
number listed in the Warranty section.
1-202-418-0177
Changes or modifications, not expressly approved by Motorola, may
void the user's authority granted by the local regulatory agency to
Canada
operate this radio and should not be made. To comply with local
No license is required in Canada for GMRS use.
regulatory requirements, transmitter adjustments should be made
only by or under the supervision of a person certified as technically
qualified to perform transmitter maintenance and repairs in the
private land mobile and fixed services as certified by an organization
representative of the user of those services. Replacement of any
transmitter component (crystal, semiconductor, etc.) not authorized
Volume
by the local agency's equipment authorization for this radio could
violate local government regulatory rules.
Note:
• Use of this outside the country where it was intended to be
Push-to-Talk
distributed is subject to government regulations and may
be prohibited.
Licensing Information Flashlight Button
Microphone
Your Motorola radio has 22 operating channels. The FRS channels
operate within the range of free use frequencies and do not require
authorization from your local regulatory body.
Call Tone
The GMRS channels may require authorization from your local
regulatory body.
Scroll/Weather
Flashlight LED
Display Screen Guide
Description Channel Frequency Description
GMRS 12 467.6625 MHz FRS
GMRS 13 467.6875 MHz FRS
Numbers for Channel,
Call Tone
GMRS 14 467.7125 MHz FRS
Numbers for Codes
GMRS 15 462.5500 MHz GMRS
GMRS 16 462.5750 MHz GMRS
— Battery Meter
GMRS 17 462.6000 MHz GMRS
— Channel Power
GMRS 18 462.6250 MHz GMRS
Indicator (see Menu
Options)
FRS 19 462.6500 MHz GMRS
— Lock
FRS 20 462.6750 MHz GMRS
— Talk Confirmation
FRS 21 462.7000 MHz GMRS Tone (Roger Beep)
— Noise Filtering
FRS 22 462.7250 MHz GMRS
— On/Off for each
feature
Getting Started
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3
AA alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack (Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Remove the NiMH battery pack from the clear plastic bag.
(Do not disassemble or unwrap the battery pack.)
4. Insert the NiMH battery pack with the diagram facing you.
5. Reposition the battery cover and press down to secure.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover latch
up and remove the cover.
3. Insert the three AA alkaline batteries with + and - polarity as
shown inside.
4. Reposition the battery cover and press down to secure.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
to empty . When the radio has one segment left, the
radio chirps periodically or after releasing
Removing the NiMH Battery Pack (Optional Accessory)
1. Turn the radio off.
For mail service: If you have
2. With the back of the radio facing you, lift the battery latch up to
Call the FCC questions about
release the battery cover and remove the cover.
Forms Hotline the FCC License:
3. Remove the NiMH battery pack by pulling the ribbon attached to
Call the FCC
the radio.
1-800-418-FORM 1-888-CALL-FCC 4. Reposition the battery cover and press down to secure.
(3676) (225-5322)
Removing the Three AA Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery latch up to
release the battery cover and remove the cover.
Control Buttons
3. Gently remove each alkaline battery by easing each battery
out individually.
4. Reposition the battery cover and press down to secure.
Notes
• Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Emergency Alert
• Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
LED Indicator permanent damage to your radio.
Using the Battery Charger (Optional Accessory)
The battery charger provides drop-in charging convenience for
NiMH batteries and can be placed on any flat surface, such as a
Accessory Jack
desk or workbench. Charge the NiMH battery overnight (at least 16
hours) before using it for the first time. After the initial charge, an
empty battery is fully charged within 14 hours.
Menu/Lock
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
Scan/Monitor
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging
pockets.
5. When charging in the battery charger, the red light on the
charger base will glow continuously.
Mini-USB
Charging Port
Using the mini-USB Charging Connector
The mini-USB charging connector is a handy port that allows you to
conveniently charge your NiMH battery pack. This is an alternative
to charging your NiMH battery pack in the Battery Charger desk
stand using the AC wall adaptor and especially useful when used
while traveling.
Available mini-USB charging options: (optional accessories)
1. Wall travel charger
2. Vehicle charger
3. Mini-USB computer cable
If using a computer, the computer must be turned on.
— Scan This and other accessories (sold separately) are available for
your radio. For more information, visit our Web site at
— Call Tone,
www.motorola.com.
Keypad Tone
1. Plug your mini-USB cable or charger into a power source as is
— Weather Alert appropriate for your accessory.
2. Plug the cable into the mini-USB port on the bottom of your radio.
— Hands-Free Use
3. An empty battery will be fully charged in 14 hours.
Without
Accessories 4. The LED indicator light on the radio will glow to indicate that the
battery is charging.
— Hands-Free Use
Notes
With Accessories
• The light will remain red after the NiMH battery pack is fully
charged.
• When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).
• For optimal battery life, remove the radio from the charger within
16 hours. Do not store the radio while connected to the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
time for the battery to charge to 1 bar before attempting to
transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to
release the catch.
2. Pull the belt clip away from the back of the radio.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to
turn the radio off.
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
2. The display screen then shows the current channel, code and
(Low Battery Alert).
all features that are enabled.
Setting the Volume
Press and hold for three seconds while rotating until you
reach a comfortable listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
Talking and Listening
To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release .
For maximum clarity, hold the radio two to three inches away from
your mouth and speak directly into the microphone. Do not cover
the microphone while talking.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet apart.
Monitor Button
Pressing and holding for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows
you to adjust the volume, if necessary. You can also press
check for activity on the current channel before you talk.
Push-to-Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio
emits a continuous warning tone and stops transmitting if you
press for 60 continuous seconds.
. Allow
to
MJ Series