Motorola KEM-PK34301-03 Talkabout User Manual

Body-Worn Operation
To maintain compliances with FCC/Health Canada RF exposure
®
guidelines if you wear a radio on your body when transmitting always
place the radio in a Motorola-supplied or approved clip holder, holster,
case or body harness for this product. Use of non-Motorola-approved
Two-Way Radio
accessories may exceed FCC/Health Canada RF exposure guidelines.
User Guide If you do not use one of the Motorola-supplied or approved body-worn
accessories and are not using the radio held in the normal use position,
ensure the radio and its antenna are at least 1 inch ( 2.5 cm) from your
body when transmitting.
Data Operation
If applicable, when using any data feature of the radio with or without an
accessory cable, position the radio and its antenna at least one inch
( 2.5 cm) from the body.
Approved Audio Accessories
• 53724: Remote Speaker with Push-to-Talk Microphone
• 53725: Headset with Swivel Boom Microphone
• 53727: Earbud with Push-to-Talk Microphone
• 53728: Flexible Ear Receiver
• 56320: Earpiece with Boom Microphone
Electromagnetic Interference/Compatibility
Note: Nearly every electronic device is susceptible to electromagnetic
interference (EMI) if inadequately shielded, designed or otherwise
configured for electromagnetic compatibility. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference; and
MT Series
KEM PK34301 03
2. This device must accept any interference received, including
interference that may cause undesired operation.
IC Canada
The term "IC:" before the equipment certification number only signifies
that the Industry Canada technical specifications were met.
Facilities
For More Information
To avoid electromagnetic interference and/or compatibility conflicts, turn
For further information, you may contact Motorola Solutions, Inc. as follows: off your radio in any facility where posted notices instruct you to do so.
Hospitals or health care facilities may be using equipment that is
USA: Call 1-800-638-5119, send e-mail to giant@callcenter.com or visit
sensitive to external RF energy.
www.motorolasolutions.com/talkabout
Uruguay: Call 00-04-01-78-70-11 Aircraft
Panama: Call 507-340-0293
When instructed to do so, turn off your radio when onboard an aircraft.
Any use of a radio must be in accordance with applicable regulations
Safety and General Information per airline crew instructions.
Medical Devices – Pacemakers
Important Information on Safe and Efficient Operation
The Advanced Medical Technology Association recommends that a
Read This Information Before Using Your Radio.
minimum separation of 6 inches (15 cm) be maintained between a
handheld wireless radio and a pacemaker. These recommendations are
The information provided in this document supersedes the general safety
consistent with the independent research by and recommendations of
information in user guides published prior to December 1, 2002.
the U.S. Food and Drug Administration.
Transmit and Receive Procedure
People with pacemakers should:
Your two-way radio contains a transmitter and a receiver. To control your
• ALWAYS keep the radio more than 6 inches (15 cm) from their
exposure and ensure compliance with the general population/
pacemaker when the radio is turned ON.
uncontrolled environment exposure limits, always adhere to the following
procedure: • Not carry the radio in the breast pocket.
• Use the ear opposite the pacemaker to minimize the potential for
• Transmit no more than 50% of the time.
interference.
• To receive calls, release the PTT button.
• Turn the radio OFF immediately if there is any reason to suspect that
• To transmit (talk), press the Push to Talk (PTT) button.
interference is taking place.
Transmitting 50% of the time, or less, is important because the radio
Medical Devices – Hearing Aids
generates measurable RF energy exposure only when transmitting (in
Some digital wireless radios may interfere with some hearing aids. In the
terms of measuring standards compliance).
event of such interference, you may want to consult your hearing aid
Exposure to Radio Frequency Energy
manufacturer to discuss alternatives.
Your Motorola two-way radio complies with the following RF energy
Medical Devices – Other
exposure standards and guidelines:
If you use any other personal medical device, consult the manufacturer
• United States Federal Communications Commission, Code of Federal
of your device to determine if it is adequately shielded from RF energy.
Regulations; 47CFR part 2 sub-part J.
Your physician may be able to assist you in obtaining this information.
• American National Standards Institute (ANSI)/Institute of Electrical
Safety and General Use While Driving
and Electronic Engineers (IEEE) C95. 1-1992.
Check the laws and regulations regarding the use of radios in the area
• Institute of Electrical and Electronics Engineers (IEEE) C95.
where you drive, and always obey them. If you do use your radio while
1-1999 Edition.
driving, please:
• International Commission on Non-Ionizing Radiation Protection
• Give full attention to driving and to the road.
(ICNIRP) 1998.
• Use hands-free operation, if available.
• Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure
• Pull off the road and park before making or answering a call if driving
to Radiofrequency Electromagnetic Fields in the Frequency Range
conditions so require.
from 3 KHz to 300 GHz, 1999.
The use of a two-way radio while engaged in activities requiring
• Australian Communications Authority Radiocommunications
concentration may cause distraction or otherwise impair your ability to
(Electromagnetic Radiation—Human Exposure) Standard, 2003.
safely participate in such activities. Always use technology safely.
• ANATEL ANNEX to Resolution No. 303 of July 2, 2002.
Do not place a portable radio in the area over an air bag or in the air bag
• ANATEL ANNEX to Resolution No. 533 of September 10, 2009.
deployment area. Air bags inflate with great force. If a portable radio is
To ensure optimal radio performance and make sure human exposure to
placed in the air bag deployment area and the air bag inflates, the radio
radio frequency electromagnetic energy is within the guidelines set forth
may be propelled with great force and cause serious injury to occupants
in the above standards, always adhere to the following procedures.
of the vehicle.
Portable Radio Operation and EME Exposure
Potentially Explosive Atmospheres
Turn off your radio prior to entering any area with a potentially explosive
Antenna Care
Use only the supplied or an approved replacement antenna. atmosphere. Only radio types that are especially qualified should be
Unauthorized antennas, modifications, or attachments could damage the used in such areas as "Intrinsically Safe." Do not remove, install or
radio and may violate FCC regulations. charge batteries in such areas. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or
Do NOT hold the antenna when the radio is "IN USE." Holding the
even death.
antenna affects its effective range.
Uruguay
Note: The areas with potentially explosive atmospheres referred to
Use of GMRS frequencies is subject to the Rules and Regulations of the
above include fueling areas such as below decks on boats, fuel or
Regulatory Unit Communications Services (URSEC). URSEC requires that
chemical transfer or storage facilities, areas where the air contains
all operators using GMRS frequencies obtain a permit before operating
chemicals or particles (such as grain, dust or metal powders) and any
their equipment. The authorization shall depend on the channel
other area where you would normally be advised to turn off your vehicle
availability at the time the authorization is requested. To obtain a permit
engine. Areas with potentially explosive atmospheres are often—but not
from URSEC, consult your local URSEC office for more information:
always—posted.
www.ursec.gub.uy.
Blasting Caps and Areas
Emergency Alert
Panama
To avoid possible interference with blasting operations, turn off your
The Republic of Panama does not require authorization to use
radio when you are near electrical blasting caps, in a blasting area, or in
FRS/GMRS radio equipment frequencies.
areas posted "Turn off two-way radios." Obey all signs and instructions.
USA
Operational Cautions
Volume
Use of GMRS frequencies is subject to the Rules and Regulations of the
Antennas
Federal Communications Commission (FCC).
Do not use any portable radio that has a damaged antenna. If a
The FCC requires that all operators using GMRS frequencies obtain a
damaged antenna comes into contact with your skin, a minor burn can
radio license before operating their equipment. To obtain the FCC forms,
result.
please visit the FCC's Web site at wireless.fcc.gov/uls/index.htm?job=
Batteries
home to source form 605 and 159, which include all the instructions you
All batteries can cause property damage and/or bodily injury such as burns
will need. If you wish to have the document faxed or mailed, or if you
if a conductive material—like jewelry, keys or beaded chains— touch
have questions, please use the following contact information:
exposed terminals. The conductive material may complete an electrical
For a fax:
circuit (short circuit) and become quite hot. Exercise care in handling any
Contact the
Push to Talk
charged battery, particularly when placing it inside a pocket, purse or other
Fax-0n-Demand
container with metal objects.
(High)
system
Exercise care when removing NiMH or AA batteries. Do not use sharp or
conductive tools to remove either of these batteries.
1-202-418-0177
Battery Charger Safety Instructions:
Save these Instructions
Push to Talk
1. Do not expose the charger to rain or snow.
(Low)
2. Do not operate or disassemble the charger if it has received a sharp
blow, or has been dropped or damaged in any way.
3. Never alter the AC cord or plug provided with the unit. If the plug will
Call Tone
not fit the outlet, have the proper outlet installed by a qualified
electrician. An improper condition can result in a risk of electric
Flash Light
shock.
Button
Emergency Alert
4. To reduce the risk of damage to the cord or plug, pull the plug rather
than the cord when disconnecting the charger from the AC
Volume
receptacle.
5. To reduce the risk of electric shock, unplug the charger from the
Scroll/Weather
outlet before attempting any maintenance or cleaning.
Push to Talk
6. Use of an attachment not recommended or sold by Motorola may
(High)
Microphone
result in a risk of fire, electric shock or personal injury.
Push to Talk
7. Make sure the cord is located so it will not be stepped on, tripped
Mini-USB
(Low)
over or subjected to damage or stress.
Call Tone
Charging Port
8. An extension cord should not be used unless absolutely necessary.
Flash Light
Button
Use of an improper extension cord could result in a risk of a fire
and/or electric shock. If an extension cord must be used, make sure
Scroll/Weather
that: Microphone
Mini-USB
• The pins on the plug of the extension cord are the same number,
Charging Port
size and shape as those on the plug of the charger.
• The extension cord is properly wired and in good condition.
• The extension cord size is 18 AWG for lengths up to 100 feet, and
16 AWG for lengths up to 150 feet.
9. The supply cord of the AC adaptor cannot be replaced. If the cord is
damaged, call customer service at 1-800-638-5119 (U.S. and Canada)
or e-mail us at giantintl@callcenter.com.
Licensing Information
Numbers for Channel,
Call Tone
Your Motorola radio has 22 operating channels. The FRS channels
operate within the range of free use frequencies and do not require
authorization from your local regulatory body.
Numbers for Codes
The GMRS channels may require authorization from your local regulatory
body.
Channels and Frequencies
—Battery Meter
Channel Frequency Description Channel Frequency Description —Channel Power
1 462.5625 MHz GMRS/FRS 12 467.6625 MHz FRS
2 462.5875 MHz GMRS/FRS 13 467.6875 MHz FRS
—Keypad Lock
3 462.6125 MHz GMRS/FRS 14 467.7125 MHz FRS
—Talk Confirmation
4 462.6375 MHz GMRS/FRS 15 462.5500 MHz GMRS
—Noise Filtering
5 462.6625 MHz GMRS/FRS 16 462.5750 MHz GMRS
—On/Off for each
6 462.6875 MHz GMRS/FRS 17 462.6000 MHz GMRS
7 462.7125 MHz GMRS/FRS 18 462.6250 MHz GMRS
8 467.5625 MHz FRS 19 462.6500 MHz GMRS
9 467.5875 MHz FRS 20 462.6750 MHz GMRS
Weatherproof
This radio is weatherproof to IP-54 standards. It is dust/splashproof from
10 467.6125 MHz FRS 21 462.7000 MHz GMRS
any direction. The radio is resistant to water and rain splashes only
when the battery cover and headset accessory mini-USB ports are
11 467.6375 MHz FRS 22 462.7250 MHz GMRS
sealed. Open the battery compartment door or headset port cover only
when the radio is dry. Use of a headset accessory should be in dry
environments only.
The charging base and AC adaptor are not waterproof. Do not expose the
charger to rain or snow. Charge the radios only in a dry location. Do not
place wet radios into the charging base. The battery door must be tightly
closed with the screw to maintain the weatherproof seal of the radio.
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or 3 AA
alkaline batteries and beeps when the batteries are low.
Installing NiMH Rechargeable Battery Pack
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
3. Remove the NiMH battery pack from the clear plastic bag (do not
disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you. (The
ribbon should be underneath the battery pack and should wrap
around the right side of the pack for easy removal.)
5. Close the battery cover and tighten the retaining screw on the
battery door.
Installing the Three AA Alkaline Batteries ( Optional Accessory)
1. Turn the radio off. LED Indicator
For mail service: If you have
Call the FCC questions about
2. With the back of the radio facing you, loosen the retaining screw on
Forms Hotline the FCC License: the battery door and open the cover.
Call the FCC
3. Insert the three AA alkaline batteries with + and - polarity as shown
Accessory Port inside. (The ribbon should be underneath the AA alkaline batteries
1-800-418-FORM 1-888-CALL-FCC
and should wrap around the right side of the batteries.)
(3676) (225-5322)
4. Close the battery cover and tighten the retaining screw on the
battery door.
Control Buttons
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
empty . When the radio has one segment left, the
Menu/ Keypad Lock
radio chirps periodically or after releasing
Line Drawing best fitting for UG
Removing the NiMH Battery Pack
Scan/Monitor
MON 1. Turn the radio off.
MENU
2. With the back of the radio facing you, loosen the retaining screw on
the battery door and open the cover.
3. Remove the NiMH battery pack by pulling the ribbon attached to
the radio.
4. Close the battery cover and tighten the retaining screw on the
LED Indicator
battery door.
Removing the Three AA Alkaline Batteries ( Optional Accessory)
Accessory Port
1. Turn the radio off.
Speaker
2. With the back of the radio facing you, loosen the retaining screw on
Menu/ Keypad Lock
the battery door and open the cover.
Scan/Monitor
MON
MENU
3. Gently remove each alkaline battery by easing each battery out
individually.
4. Close the battery cover and tighten the retaining screw on the
Speaker battery door.
Notes
• Exercise care when removing NiMH or AA batteries. Do not use
sharp or conductive tools to remove either of these batteries.
Flash Light LED
• Remove the batteries before storing your radio for extended periods
Display Screen Guide
Flash Light LED
of time. Batteries corrode over time and may cause permanent
Numbers for Channel,
Call Tone
damage to your radio.
Numbers for Codes
Using the mini-USB Charging Adaptor
—Battery Meter
—Vibrate
—Scan The mini-USB charging adaptor allows you to conveniently charge your
—Channel Power
Indicator
—Dual Scan
(see menu Options)
NiMH battery pack. This is an alternative to charging your NiMH battery
—Call Tone,
—Keypad Lock Keypad Tone
pack in the Battery Charger desk stand using the AC wall adaptor and
—Talk Confirmation —Weather Alert
Tone (Roger Beep)
—Hands-Free Use
especially useful when used while traveling.
Without
—Noise Filtering
Accessories
—On/Off for each
—Hands-Free Use
feature Available mini-USB charging options:
With Accessories
1. Vehicle charger
2. Mini-USB computer cable
If using a computer, the computer must be turned on.
—Vibrate
This and other accessories (sold separately) are available for your radio.
—Scan
For more information, visit our Web site at
Indicator
—Dual Scan
motorolasolutions.com/talkabout or shop.giantintl.com.
(see menu Options)
—Call Tone, 1. Plug your mini-USB cable or charger into a power source as is
Keypad Tone appropriate for your accessory.
2. Plug the cable into the mini-USB port on the bottom of your radio.
—Weather Alert
3. After the initial charge, an empty battery will be fully charged in 7 hrs.
Tone (Roger Beep)
—Hands-Free Use
for the MT350 series radio (KEBT-650 mAh NiMH battery pack) or 14
Without
hrs. for the MT352 series radio (KEBT-1300 mAh NiMH battery pack).
Accessories
4. The battery icon will scroll as the battery is being charged. The
scrolling icon will stop when the battery is fully charged.
—Hands-Free Use
feature
Notes
With Accessories
• When moving between hot and cold temperatures, do not charge the
NiMH battery pack until the battery temperature acclimates (usually
about 20 minutes).
Getting Started
• For optimal battery life, remove the radio from the charger within 16
hours. Do not store the radio while connected to the charger.
• If the radio is kept on while charging, the charging time will be
extended.
• Even though the charger is connected, you may not be able to
transmit a message if the battery is completely empty
time for the battery to charge to 1 bar
transmit a message.
Attaching and Removing the Belt Clip
1. Attach belt clip to pocket or belt strap.
2. Align the belt clip post with the hole in the back of the radio.
3. Gently push until the clip clicks in place.
To Remove
1. Push down on the release tab at the top of the belt clip to release
the catch.
2. Pull the belt clip away from the back of the radio.
Using the Desktop Battery Charger ( Optional Accessory)
The battery charger provides drop-in charging convenience for NiMH
batteries and can be placed on any flat surface, such as a desk or
workbench. Charge the NiMH battery overnight (at least 16 hours) before
using it for the first time.
MT350R Radio
After the initial charge, an empty battery (KEBT-650 mAh NiMH) is fully
charged within 7 hrs.
MT352R Radio
After the initial charge, an empty battery (KEBT-1300 mAh NiMH) is fully
charged within 14 hrs.
1. Follow the steps above to install a NiMH Battery Pack.
2. Plug the AC power supply cord into the jack on the desk stand.
3. Plug the AC power supply into a standard wall outlet.
4. With a radio facing forward, slide it into one of the charging pockets.
5. When charging in the battery charger, the red light on the charger
base will glow continuously.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to turn the
radio off.
to
1. In the ON position, the radio chirps and briefly shows all feature
icons available on the radio.
MT350 (Low Battery Alert).
2. The display screen then shows the current channel, code and all
features that are enabled.
Setting the Volume
Press and hold for three seconds, then rotate
comfortable listening level.
1. Rotate clockwise to increase the volume.
Emergency Alert
Volume
2. Rotate counterclockwise to decrease the volume.
LED Indicator
Push to Talk Do not hold the radio close to your ear. If the volume is set to an
(High)
Accessory Port
Push to Talk uncomfortable level, it could hurt your ear.
(Low)
Menu/ Keypad Lock
Call Tone
Flash Light Scan/Monitor
MENU MON
Button
Scroll/Weather
Microphone Talking and Listening
Mini-USB Speaker
Charging Port
Flash Light LED To communicate, all radios in your group must be set to the same
channel and Interference Eliminator Code.
1. To talk, press and hold .
2. When you are finished talking, release
Numbers for Channel, For maximum clarity, hold the radio two to three inches away from your
Call Tone
mouth and speak directly into the microphone. Do not cover the
Numbers for Codes
microphone while talking.
—Battery Meter
—Vibrate
—Channel Power —Scan
Talk Range
Indicator —Dual Scan
(see menu Options)
—Call Tone,
Your radio is designed to maximize performance and improve
—Keypad Lock Keypad Tone
—Weather Alert
—Talk Confirmation
Tone (Roger Beep) transmission range. Do not use the radios closer than five feet apart.
—Hands-Free Use
Without
—Noise Filtering
Accessories
—On/Off for each Power Boost
—Hands-Free Use
feature
With Accessories
To boost your radio's power up to high power, press the top portion of the
button when talking. If you know your party is close by, you can
conserve your battery's energy by pushing the lower part of the
button to use less power.
Note: If you are on an FRS only channel (see Channels and Frequencies
table) the radio will only use low power when either portion of the
is pressed.
Monitor Button
Pressing and holding for three seconds allows you to listen to the
volume level of the radio when you are not receiving. This allows you to
adjust the volume, if necessary. You can also press
activity on the current channel before you talk.
Push to Talk Timeout Timer
To prevent accidental transmissions and save battery life, the radio emits
a continuous warning tone and stops transmitting if you press
continuous seconds.
Menu Options
Selecting the Channel
Your radio has 22 channels. The channel is the frequency the radio uses to
transmit. Channels 8-14 are FRS 0.5 watt only and all other channels are
GMRS. (See the "Channels and Frequencies" table under "Licensing
Information" for details.)
1. With the radio on, press . When the radio is on a 0.5
watt channel, displays. When the radio is on a 1.5 watts
channel, displays. The current channel flashes.
2. Press or and select an unused or quiet channel.
. Allow
3. Press to save the channel setting or
before attempting to
Line Drawing
Emergency Alert
Volume
Push to Talk
(High)
Push to Talk
(Low)
Call Tone
Flash Light
Button
Scroll/Weather
Microphone
Mini-USB
Charging Port
until you reach a
Numbers for Cha
Call Tone
.
Numbers for Cod
—Battery M
—Channel P
Indicator
(see menu
—Keypad Lo
—Talk Confi
Tone (Rog
—Noise Filt
—On/Off fo
feature
to check for
for 60
to continue set up.
Continued on back
MT Series